• 한국유체기계학회 논문집
• /
• 제13권1호
• /
• pp.23-28
• /
• 2010

A draft tube which has impeller to elevate bottom water and spread it over surface of lake water, induces convective circulation of lake water, a Long-Distance Circulation (LDC). Circulation of lake water make stratified water mixed and enhance DO (Dissolved Oxygen) of bottom water. Circulation rate of water is determined by draft rate of the tube, which is dependent on design parameters of the draft tube system, i. e. dimension of impeller and diffuser, inclined angle of impeller, impeller shape, and rotational speed. In this study, change in draft rate and power consumption of circulation equipment was investigated numerically with changing impeller dimension, angle and rotational speed. It was found that flowrate of draft water was increased as the dimensions of draft tube and impeller, and rotational speed and inclined angle of impeller increased. The power consumption was also elevated with increasing parameter values, and final selection of parameter values was made to satisfy target flowrates and power consumption.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권4호
• /
• pp.550-556
• /
• 2008

The aim of this research is to analyze the influence of motive pressure, driving nozzle position and nozzle throat ratio on the performance of ejector. The experiment was conducted in the variation of motive pressure of 0.196, 0.294, 0.392 and 0.490MPa respectively. The position of driving nozzle was varied in difference locations according to mixing tube diameter(0.5d, 1d, 2d, 3d, 4.15d, 5d and 6d). The experimental results show when the nozzle outlet is located at 3d, the flow characteristics change abruptly. It is shown that the suction flow rate and pressure lift ratio of ejector is influenced by the driving nozzle position. At nozzle position location of the Id of mixing tube diameter the performance of ejector gives the best performance.

• 설비공학논문집
• /
• 제5권3호
• /
• pp.187-197
• /
• 1993

In this study, the numerical analysis and experiments of the hot water storage using the thermal stratification techniques were carried out. The CPU time for a typical run of the the thermal stratification up to 900 seconds took one week for a $81{\times}31$ mesh size and 10 days for a $118{\times}31$ mesh size, respectively, for a cylindrical shape of the storage. In the initial stage, the numerical results were in favorable agreement with the experimental results, but it showed that the temperature gradients in the storage decreased gradually with time. It was also found that the increase of ${\delta}t$ decreased the convergent speed due to the intensive fluctuation of the velocity field in every iteration. The increase of numbers of grids is projected to forecast a more accurate result, but it made the computing time longer and woul slow down convergence. At the experiments of the flow visualization, it was confirmed that the thermal stratification was apparently built up due to the installation of diffuser at the lower part of the storage. Thus, the thermal performance of the storage could be improved by installing the diffusers at the inlet and outlet.

• 한국자동차공학회논문집
• /
• 제14권5호
• /
• pp.138-144
• /
• 2006

This research represents the catalytic converter for application in the motorcycle. Present research model type is a monolithic catalytic converter and this type has been widely used for satisfaction on and the regulations of pollutant emissions in automobiles. The experiment range is found for light-off temperature time of the catalyst converter. And we has to experiment for effective area of catalytic monolith. The experimental result indicated an increase effective area in the catalytic monolith. Specialty, it was found from the result that the more positive effect from result of thermal image camera in the megaphone model. The rate of effective area for base model was about 8.97% and megaphone model was 41.52%, 34.60%, 33.43%, 25.43% and 17.82% on the diffuser angle $4^{\circ}$ to $8^{\circ}$. Comparing with base type, megaphone type has more suitable for application to motorcycle.

• 소성∙가공
• /
• 제20권1호
• /
• pp.11-16
• /
• 2011

Recently, according to the rapid development of display, many display applications, such as, cellular phone, navigation, monitor and LCD TV have been changed from CRT type to LCD type. BLU(Back Light Unit) is one of main parts in LCD unit and generally, it consists of a light source, a reflective sheet, a LGP(Light Guide Plate), a diffuser sheet, and two prism sheets. The most important component of BLU is a light guide plate, which diffuses the input light to the TFT-LCD module uniformly. The LGP is usually made by injection molding process, and it has numerous optical micro patterns on the surface. In the present study the micro-patterned stamper which has cylindrical shape was fabricated by using the UV-LiGA process. And the replication characteristics have been compared among three different kinds of injection molding process; general injection molding, injection/compression molding and RHCM(Rapid Heating and Cooling Molding). Average replication ratios of CIM and ICM were 19.1% and 64.6%, respectively. On the other hand, the average replication ratio of RHCM process showed the higher value of 98.4% among these. It show that maintaining the mold surface above $T_g$ could increase the replication ratio of micro patterns substantially.

• 한국지열·수열에너지학회논문집
• /
• 제10권4호
• /
• pp.15-24
• /
• 2014

This study conducted a computational fluid dynamics(CFD) analysis to find an appropriate diameter or sectional area of air ducts and fluid pipes which have an electromagnetic pulse(EMP) shied to protect indoor electronic devices in special buildings like military fortifications. The result shows that the optimized outdoor air intake size can be defined with either the ratio of the maximum air velocity in the supply duct to the air intake size, or the shape ratio of indoor supply diffuser to the outdoor air intake. In the case of water channel, the fluid velocity at EMP shield with the identical size of the pipe, decreases by 25% in average due to the resistance of the shield. The enlargement of diameter at the shield, 2 step, improves the fluid flow. It illustrated that the diameter of downstream pipe size is 1step larger than the upstream for providing the design flow rate. The shield increases friction and resistance, in the case of oil pipe, so the average flow velocity at the middle of the shield increase by 50% in average. In consideration of the fluid viscosity, the oil pipe should be enlarged 4 or 5 step from the typical design configuration. Therefore, the fluid channel size for air, water, and oil, should be reconsidered by the engineering approach when EMP shield is placed in the middle of channel.

• 한국광학회지
• /
• 제18권6호
• /
• pp.401-409
• /
• 2007

액정 디스플레이에 사용하는 직하형 Back Light Unit(BLU)의 확산판과 프리즘판의 개수를 줄이면서도 성능을 개선한 새로운 일체형 복합필름을 제안하고 이들의 광학적 성능을 시뮬레이션으로 분석하였다. 막대 프리즘의 형태와 원통 렌즈 형태를 하나로 합친 복잡한 일차원 형태의 광학프리즘을 만든 후, 이를 연속적으로 배열하여 일체형 복합필름을 구성하였다. 일체형 복합필름의 성능은 조명계 프로그램으로 확인하여 최적의 구조를 정하였다. 이러한 최적 조건하에서 한 장의 일체형 복합필름을 사용하는 10인치 크기의 BLU에서 계산한 광효율은 53.5%이고, 광휘도 균일도는 83.5%였으며, 각도별 광휘도 분포인 배광곡선은 수직으로 $90^{\circ}$이고 수평방향으로 $112.5^{\circ}$이다. 그리고 이러한 설계로 새로운 일체형 복합필름을 제작하였다.

• 문화기술의 융합
• /
• 제6권1호
• /
• pp.501-506
• /
• 2020

본 실험 연구에서는 대표적인 네 가지 타입의 승용차 차량형태에 대한 공기역학(공력) 성능 분석, 측면 유리의 각도에 따른 공력 성능 분석, 엔진후드(엔진 덮개)의 각도차이에 따른 공력 성능 분석, 루프 라인의 각도 차이에 따른 공력 성능 분석을 통해 차량의 형태 변화에 따라 공력 성능이 어떻게 변화하는지를 종합적으로 분석해 보았다. 실험결과 비스듬히 떨어지는 후면 유리 라인은 공력 성능을 저하시켰고, 루프의 각도 차이에 따른 공력 성능 차이는 거의 나타나지 않았으며 일찍 떨어지는 후면 라인은 공력 성능에 가시적인 영향을 끼치지 않았다. 차량의 루프라인이 수평으로 늦게까지 이어지다 천천히 떨어지는 후면 유리 라인은 스타일링에 도움이 될지언정 공력 성능은 저하시켰다. 후방 디퓨저의 경우 차체의 형태에 따라 그 성능 효과가 달라지는 것으로 판단되었다.

• 한국추진공학회지
• /
• 제22권5호
• /
• pp.66-72
• /
• 2018

연소가스를 이용하여 압력비와 램 구조물의 형상에 따른 이차목 디퓨저의 성능 특성에 대한 수치적 연구를 수행하였다. 작동 조건인 압력비 75에서 램 구조물의 각도가 커짐에 따라 유동의 모멘텀 감소로 인해 진공실 압력이 상승하였다. 또한, 램 구조물의 반각 $15^{\circ}$, 폐색율 15%일 때, 디퓨저는 압력비 36과 37 사이에서 시동되었다. 이를 토대로 다양한 압력비와 램 구조물 형상에 따른 최적의 램 구조물 형상은 반각 $5{\sim}20^{\circ}$, 폐색율 15~40%로 판단된다.

• 대한기계학회논문집B
• /
• 제38권2호
• /
• pp.115-120
• /
• 2014

자동차용 터보차저 압축기의 성능 개선을 위해 원주방향의 볼류트 입구 높이들이 수정되었고 디퓨저를 포함한 볼류트에 대한 유동장이 상용 소프트웨어를 사용하여 조사되었다. 기본적으로 잘 설계된 볼류트는 높은 압력회복계수와 낮은 전압력손실계수를 보여주어야 한다. 본 연구에서는 동일한 단면형상과 설단면각(Tongue Angle)을 가지나 원주방향으로는 서로 다른 볼류트 입구 높이를 갖는 두 경우의 원형단면 볼류트가 선정되었다. 하나는 $90^{\circ}$ 원주방향에서는 단면 중앙으로 유입되나 이후의 원주방향에서는 볼류트 단면 최하단부들을 잇는 접선과 동일한 높이를 유지하면서 점진적으로 하단부로 유입되는 볼류트 형상이다(케이스 1 볼류트). 다른 하나는 설단면에서는 접선방향으로 유입되도록 모든 원주방향에 대하여 입구 높이를 2 mm 낮춘 형상이다(케이스 2 볼류트). 해석결과, 케이스 2 볼류트가 케이스 1 볼류트보다 높은 압력회복계수로 인한 높은 전압력비와 낮은 전압력손실계수로 인한 높은 등엔트로피 효율을 보여주었다.