• Journal of ILASS-Korea
• /
• v.19 no.3
• /
• pp.142-148
• /
• 2014

In this study, characteristics of gaseous pollutants and particulate matter were investigated on the condition of DPF regeneration and normal DPF condition. THC, CO, $CO_2$, NOx, and $CH_4$ were analyzed by MEXA-7200H and CVS-7100 respectively. Particulate Matter (PM) was measured by difference in weight of Membrane filter. Particle Number (PN) was measured by CPC analyzer. And Sulfate, Nitrate, Organic were measured by Aerosol Mass Spectrometer (AMS). As a result, gaseous pollutants and particulate matter were detected in higher concentration during DPF regeneration than normal DPF condition. And the PN increased by 94%, the fuel consumption was reduced by 29% on DPF generation process. Sulfate, Nitrate and Organic were undetectable level during normal DPF condition. But the highest concentration of Sulfate, Nitrate and Organic were measured as $100{\mu}g/m^3$, $20{\mu}g/m^3$ and $15{\mu}g/m^3$ respectively on DPF regeneration condition. VOCs concentrations (Benzene, Toluene, Ethylbenzene, Xylene) were analyzed by using PTR-MS. Benzene and Toluene emission have little or no change depending on DPF regeneration. But the Ethylbenzene and Xylene have comparatively low emissions on DPF regeneration.

• Journal of Power System Engineering
• /
• v.20 no.5
• /
• pp.37-45
• /
• 2016

Exhaust gas recirculation has the advantage of being low-cost and easy to control of NOx emission. Therefore, it is most generally used to reduce NOx emission according to strengthen regulation. In the case of a non-road engine, such as the agricultural engine, since it mainly operate a middle or high-load state, NOx emission is decreased in accordance with the mapping range of the EGR rate, but results in an increase in the particulate matter which is caused to deposit and fouling problem of the EGR system. This problem has become an important issue for maintaining the performance of the engine, as well as emission performance. This study had examined the effects of cooler aging on the performance of heat transfer efficiency and NOx emission in non-road diesel engine. As a result of the EGR cooler aging during 200 hours engine operation, the cooling performance decreased about 25% compared with that of fresh cooler and the NOx emission increased about 14.6% on NRSC(non-road steady cycle) and 20% on NRTC(non-road transient cycle) compared with that of fresh cooler respectively.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.4
• /
• pp.37-43
• /
• 2003

The exhaust gas recirculation (EGR) is needed for one of various strategies to reduce NOx emission. But to get the proper EGR rate, the intake and exhaust system become complicated, also application of EGR system is difficult because of the penalty in fuel consumption and the increase in particulate matter. This study is focused on the development of EGR valve using the electrical method. The effects of EGR on the characteristics of NOx, CO, CO2 emissions and particulate mater have been investigated using small-displacement size 0.8-liters engine of diesel passenger car operating at several loads and speeds. After the analysis and comparison between conventional E-EGR valve and developed E-EGR valve performance by test bench, the estimation of vehicle application was executed through the EGR map and CVS-75 test result measured on the chassis dynamometer.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.3
• /
• pp.278-284
• /
• 2006

The popularity of the diesel engine revolves around its fuel efficiency, reliability, and durability compared to the gasoline engine. However, the main disadvantage of diesel engine is the emission of particulate matter (PM) which is known as carcinogenic substance. Therefore recent progress in engine management and after-treatment systems has led to great improvement to satisfy strict emission regulations. To comply with powerful environment regulations, this study is focused on the decrease of PM(soot) as to increase significantly exhaust temperature. Therefore, HC injection is used as the method to go to the PM regeneration temperature in front of filters composed of diesel oxidation catalyst(DOC) and diesel particulate filter(DPF). And especially, LPG is used because it has good chemical reactions with exhaust. In this study, we could manufacture the test bench thought LPG injection - with which soot can be decreased-, construct 3 kinds of database(DB) according to quantity of temperature to decide the LPG injection quantity and develop DPF ECU algorithm.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.60-68
• /
• 2002

Experiments have been conducted to investigate the effects of emulsified fuels on the spray characteristics and exhaust emissions in a diesel engine. Four different fuels were examined : diesel, emulsified fuels with water contents which were varied with 13, 15, and l7wt%. Characteristics of fuel spray were measured by an optical method, PLLIF(planar liquid laser induced fluorescence). Compared to diesel fuel, emulsified fuels which had relatively high kinematic viscosity showed smaller spray angle and longer spray tip penetration. The qualitative droplet distributions of emulsified fuels showed worse atomization process than that of diesel fuel. As the water contents were increased, PM and NOx could be reduced simultaneously. It was specially noted that the emulsified fuel with l7wt% water content was found to be the best in reducing rates, NOx 30% and PM 40%.

• Journal of Korean Society for Atmospheric Environment
• /
• v.18 no.5
• /
• pp.411-417
• /
• 2002

The purpose of this study is to evaluate the emission reduction characteristics depending on the formation of the catalyst which influences the development of the diesel oxidation catalyst (DOC) suitable for small-sized diesel engines. We also attempted to suggest the feasibility of it as an after-treatment device. The reduction efficiency of DOC for CO and HC was proportional to the contents of precious metals, and the particulate matter (PM) has been reduced as much as 53∼59%. The reduction rate of soluble organic fraction (SOF) by DOC attachment revealed 100%. The composition of sulfate in PM increased from 3%, 7∼11% by installation of DOC. It is described that increase of sulfate contributed to the production of PM. This result also showed that the SOF and sulfate have trade-off relationship.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2000.06a
• /
• pp.83-91
• /
• 2000

This paper illustrates a new idea methods and results of WPD oil applied to marine diesel engines. in recent years, we must make an effort to develop an advanced technique for recycling of waste plastics in order to utilize scrapped plastics as fuel source for diesel engine. It is very important and necessary for us to cope with the increasing calorific value and the growing need of environment protection. The experiment fuel oil was obtained by mixing of diesel oil, WPD and water.

• Journal of Power System Engineering
• /
• v.12 no.5
• /
• pp.14-19
• /
• 2008

In order to meet stringent future emission regulations, especially to reduce Particulate Matter (PM) and NOX, stoichiometric diesel combustion technology with a piezo group-hole nozzle injector is being researched for reduction harmful emissions. A new nozzle layout, namely a group-hole nozzle, which has one group of small orifices with a wide spray included angle was investigated to improve the efficiency of stoichiometric diesel combustion. From this point of view, the group-hole nozzle suggested by Dense Co. is an attractive candidate method applicable to stoichiometric diesel combustion. The group-hole nozzle concept is to reduce the injector nozzle hole diameters without sacrificing spray penetration by closely locating two holes. Experimental studies have proven that the spray from group-hole nozzles have similar spray penetration to that of a single hole with equivalent overall nozzle hole area, but the spray drop sizes (SMD) are reduced, aiding vaporization and mixing.

• Tunnel and Underground Space
• /
• v.6 no.1
• /
• pp.48-56
• /
• 1996

Presently, mobile diesel equipments contribute a lot to improve the economic feasibility of underground mining and tunneling operations. Even in Korea, a lot of diesel equipments are being applied to the undergroud workings already, but the technology of management and control of them is not sufficient yet. This study handled the production procedure, characteristics and evaluation technology on diesel particulate matte(DPM) which is known as a carcinogen. For easy measurement of DPM using laser dust monitor, conversion known as a carcinogen. For easy measurement of DPM using laser dust monitor, conversion factor(k) to gravimetric concentration has been acquired. It is appeared that the critical material among the diesel exhaust pollutants is becoming DPM instead of NOx from this year of 1996 according to the Government regulation.

• Safety and Health at Work
• /
• v.10 no.1
• /
• pp.47-53
• /
• 2019

Background: Despite growing concern over occupational exposure to particulate matter (PM) such as grain dust and diesel exhaust, information about the exposure level and health implications among workers in small-scale milling enterprises in developing countries like Nigeria has not been adequately documented. The purpose of this study was to assess the level of exposure to grain dust and diesel exhaust and effect on lung function among grain millers in food markets in Ibadan metropolis, Nigeria. Methods: The study adopted descriptive cross-sectional design with a comparative approach. Sixteen grain milling shops each were randomly selected from two major food markets in Ibadan metropolis for indoor $PM_{10}$ and $PM_{2.5}$ monitoring. Seventy-two respondents each were proportionately selected from grain millers and shop owners for forced expiratory volume in one second and peak expiratory flow rate tests. Results: The $PM_{2.5}$ concentrations for both market locations ranged between 1,269.3 and $651.7{\mu}g/m^3$, while $PM_{10}$ concentrations were between 1,048.2 and $818.1{\mu}g/m^3$. The recorded concentrations exceeded the World Health Organization guideline limit of $50{\mu}g/m^3$ and $25{\mu}g/m^3$ for $PM_{2.5}$ and $PM_{10}$, respectively. As compared with control group (2.1 L), significantly lower forced expiratory volume in one second value (1.61 L) was observed among the exposed group (p < 0.05). Likewise, significantly lower peak expiratory flow rate value (186.7 L/min) was recorded among the exposed group than the control group (269.51 L/min) (p < 0.05). Conclusion: Exposure to grain dust and diesel exhaust accentuated respiratory disorders with declines in lung functions amongst grain millers. Improved milling practices and engaging cleaner milling facilities should be adopted to minimize exposure and related hazards.