• Tribology and Lubricants
• /
• v.21 no.6
• /
• pp.249-255
• /
• 2005

In this paper, the friction characteristic of engine bearings has been analyzed in terms of a friction loss power, a minimum film thickness and an oil film pressure. This analysis has been focused on the fuel economy improvement with a low viscosity engine oil such as SAE 0W-40, which is used for a friction loss reduction and increased for a Diesel fuel economy. The friction loss power, the minimum oil film thickness and oil film pressure distribution for plain bearings of a Diesel engine are analyzed using an AVL's EXCITE program with a conventional engine oils of SAE 5W-40 and 10W-40, and a low viscosity engine oil of SAE 0W-40. The computed results indicate that a viscosity of engine oils is closely related to the friction loss power and the decreased minimum film thickness in which is a key parameter of a load carrying capacity of an oil film pressure distribution. When the low viscosity engine oil is supplied to engine bearings, it does not affect to the formation of a minimum oil film thickness. But the friction loss power has been significantly affected by low viscosity engine oil at a low operating temperature of 0. Based on the FEM computed results, the low viscosity engine oil at a low temperature range will be an important factor for an improvement of the fuel economy improvement.

• Applied Chemistry for Engineering
• /
• v.34 no.6
• /
• pp.649-659
• /
• 2023

This study was initiated to evaluate the phosphorus (P) removal and diesel oil degradation by bacteria isolated from industrial wastewater. The bacteria isolated were identified as Bacillus sp. The P removal efficiencies by Bacillus sp. were 99% at the initial 20 mg/L P concentration. The diesel degradation efficiencies by Bacillus sp. were 86.4% at an initial 1% diesel concentration. Lipophilicity by bacteria was the highest in the log phase, whereas it was the lowest in the death phase. As the diesel was used as a carbon source, P removal efficiencies by Bacillus sp. were 68%. When glucose, acetate, and a mixture of glucose and acetate as second carbon sources were added, the diesel degradation efficiencies were 69.22%, 65.46%, and 51.46%, respectively. The diesel degradation efficiency was higher in the individual additions of glucose or acetate than in the mixture of glucose and acetate. When P concentration increased from 20 mg/L to 30 mg/L, the diesel degradation efficiency was increased by 7% from 65% to 72%, whereas when P concentration was increased from 30 mg/L to 40 mg/L, there was no increase in diesel degradation. One of the five proteins identified by proteome analysis in the 0.5% diesel-treated samples may be involved in alkane degradation and is known as the cytochrome P450 system. Also, two of the sixteen proteins identified in the 1.5% diesel-treated samples may be implicated in the fatty acid transport system and alcohol dehydrogenation.

• Journal of Biosystems Engineering
• /
• v.28 no.1
• /
• pp.11-18
• /
• 2003

This study was carried cut to get basic data of troubles in starting and supply of farm diesel engines in cold winter. The results of the study are summarized as follows: 1. As the result of farm survey. the proportions of farms which had starting problems or troubles in fuel supply in cold winter for the last 5 years were 38% for the farms with power-tillers and 32% for the farms with tractors. Most of the farms which had starting problems or troubles in fuel supply in cold winter used light oil for summer. spring or fall rather than for winter. 2. As the result of fuel supply test, fuel supply was stopped at -6$^{\circ}C$ and -18$^{\circ}C$ for summer light oil and winter light oil. respectively 3. The lowest temperatures of winter light oil for starting engine were -7.5$^{\circ}C$ for power-tiller. -12.5$^{\circ}C$ for tractor of 38ps, and -17.5$^{\circ}C$ for tractor of 45ps. which were 5~7.5$^{\circ}C$ lower than that of summer light oil. 4. The performance of engine starting and the trouble of fuel supply system at lower temperature were significantly improved by using winter hight oil rather than summer light oil.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.2
• /
• pp.181-187
• /
• 2003

Biodiesel fuel as an alternative fuel for diesel engine has a great possibility to solve the problems such as air pollution. It is a domestically produced, renewable fuel that can be manufactured from vegetable oils, used vegetable oils, or animal fats. In this study, the usability of biodiesel fuel derived from rice bran oil as an alternative fuel for diesel engines was investigated in agricultural diesel engine. Emissions were characterized with neat biodiesel fuel and with a blend of biodiesel fuel and conventional diesel fuel. Since the biodiesel fuel includes oxygen of about 11%, it could influence the combustion process strongly. So, the use of biodiesel fuel resulted in lower emissions of carbon monoxide, carbon dioxide, and smoke emissions without any increase of oxides of nitrogen. It is concluded that biodiesel fuel can be utilized effectively as a renewable and an environmentally Innocuous fuel for diesel engine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.2
• /
• pp.37-44
• /
• 2013

Generally, a reduced chemical mechanism of n-heptane is used as chemical fuel of a 3-D diesel engine simulation because diesel fuel consists of hundreds of chemical components and various chemical classes so that it is very complex and large to use for the calculation. However, the importance of fuel in a 3-D simulation increases because detailed fuel characteristics are the key factor in the recent engine research such as homogeneous charged compression ignition engine. In this study, normal paraffin, iso paraffin and aromatics were selected to represent diesel characteristics and n-dodecane was used as a representative normal paraffin to describe the heavy molecular weight of diesel oil (C10~C20). Reduced kinetics of iso-octane and toluene which are representative species of iso paraffin and aromatics respectively were developed in the previous study. Some species were selected based on the sensitivity analysis and a mechanism was developed based on the general oxidation scheme. The ignition delay times, maximum pressure and temperature of the new reduced n-dodecane chemical mechanisms were well matched to the detailed mechanism data.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.403-408
• /
• 2007

According as diesel automobile are produced, reduce noise and vibration that is occurred by characteristic of diesel engine, and need engine room layout optimization and research for light weight of parts. Balance Shaft Module is module parts for vehicles engine to improve performance and efficiency of engine and reduce noise and vibration. These days, an oil pump integrated balance shaft module and an oil sump integrated balance shaft module is on the rising for optimizing of engine room. In this study, produced prototype of oil pump integrated type balance shaft module, and achieved dynamic characteristic test about experimental modal analysis and noise/vibration of balance shaft module.

• Journal of Biosystems Engineering
• /
• v.35 no.3
• /
• pp.158-162
• /
• 2010

The effect of fuel injection characteristics on engine performance has been known for improving fuel economy and emission reduction. In this study, the spray characteristics of crude palm oil blended fuel with conventional diesel fuel was investigated. The experiments were performed to evaluate the effect of crude palm oil blending ratio and injection pressure on the spray behavior. The droplet size of injected fuel was analyzed through laser diffraction particle analyzer (LDPA). Also, spray atomization characteristics were investigated in terms of Sauter mean diameter (SMD) and droplet distribution at various injection conditions. Fuel containing crude palm oil has different spray pattern on account of the high viscosity. Through those experimental results, we found that the increase of blending ratio made droplet size larger, SMD of biodiesel 100% was increased 30.2% than that of diesel fuel 100% under injection pressure of 60 MPa.

• Tribology and Lubricants
• /
• v.19 no.5
• /
• pp.251-258
• /
• 2003

New method and device for the on-line measurement of soot concentration in a diesel engine oil are proposed, where the measurement principle is based mainly on attenuated internal total reflection. The detector were evaluated in various ranges of contaminated oils by carbon black particles. It was found that the proposed detector could be well used to monitor the oil deterioration due to soot contamination. Operational range of the detector was found from 0 to 5 mass percentage of soot content. Test results with water and fuel dilution showed that these effects were not remarkable. However, adsorption of carbon black particles onto the measurement surface was considered to be a critical problem of the detector. Effects of particle deposition on the interface was experimentally evaluated with the oil temperature and flow turbulence and discussed throughout this work.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2003.10a
• /
• pp.183-186
• /
• 2003

This study was conducted to evaluate effects by adding oil to clay soil and influences of remained oil in soil as time elapsed. Unconfined compression test and direct shear test were performed to analyze strength properties of contaminants in clayey soil. As a results of $q_u$ test for kerosene and diesel contaminated clayey soil indicate that were decreased from near 5% oil content rapidly and the declination of strength were blunt as oil content over 10%. The cohesions(c) and internal friction angle(${\psi}$) of kerosene contaminated clayey soil were not varied as quantities of kerosene in clayey soil increased. In the case of diesel contaminated clayey soil, the cohesions(c) were decreased and the internal friction angle(${\psi}$) were increased.

• Journal of the Korean Chemical Society
• /
• v.15 no.6
• /
• pp.330-347
• /
• 1971

Catalytic effects of metallic salts on the combustion of diesel fuel oil have been studied. In the case of organometallic salt, the active species are the metallic oxides resulted from combustion of the salts. The oxides act only on the residual solid carbon produced from the fuel oil combustion. The catalytic activity can be explained with the semiconductor theory just as in the case of the gas phase reaction. The chemical rate constant of the combustion of carbon, the soot from diesel fuel oil, is found to be $k_c=1.1{\times}10^4\;exp$ (-16,600/T) below $800^{\circ}K$. By addition of metallic oxides, the rate constant increases remarkably. This work has substantiated the belief that the effect of the metallic salts on the fuel oil combustion can conveniently be studied by checking directly the effect of the corresponding metallic oxide on the soot carbon.