• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.9
• /
• pp.1317-1324
• /
• 1998

In general, DI gasoline engine has the advantages of higher power output, higher thermal efficiency, higher EGR tolerance and lower emissions due to the operation characteristics of increased volumetric efficiency, compression ratio and ultra-lean combustion scheme. In order to apply the concept of stratified charge into direct injection gasoline engine, some kinds of methodologies have been adapted in various papers. In this study, a reflector was adapted around the injector nozzle to apply the concept of stratified charge combustion which leads the air-fuel mixture to be rich near spark plug. Therefore, the mixture near the spark plug is locally rich to ignite while the lean mixture is wholly introduced into the combustion chamber. The characteristics of combustion is analyzed with the variations of fuel injection pressure and load in a stratified -charge direct injection single cylinder gasoline engine. The obtained results are summarized as follows ; 1. The MBT spark timing approached to TDC with the increase of load on account of the increase of evaporation energy, but has little relation with fuel injection pressure. 2. The stratification effects are apparent with the increase of injection pressure. It is considered by the development of secondary diffusive combustion and the increase of heat release of same region, but proceed rapidly than diesel engine. Especially, in the case of high pressure injection (l70bar) and high load (3.0kgf m), the diffusive combustion parts are developed excessively and results in the decrease of peak pressure than in the case of middle load. 3. The index of engine stability, COVimep value, is drastically decreased with the increase of load. 4. To get better performance of DI gasoline engine development, staged optimizaion must be needed such as injection pressure, reflector, intake swirl, injection timing, chamber shape, ignition system and so on. In this study, the I50bar injection pressure is appeared as the optimum.

• Journal of Institute of Convergence Technology
• /
• v.2 no.1
• /
• pp.24-30
• /
• 2012

In this study, the trucks(2.9-liter) have been developed to use DME as fuel, and performance test of the vehicle's DME engine, power, emissions, fuel economy and vehicle aspects was conducted. For experiments, the fuel system(common-rail injectors and high-pressure pump included) and the engine control logic was developed, and ECU mapping was performed. As a result, the rail pressure from 40MPa to approximately 65% increase compared to the base injector has been confirmed that. Also, the pump discharge flow is 15.5 kg/h when the fuel rail pressure is 400rpm(40 MPa), and the pump discharge flow is 92.1 kg/h when the fuel rail pressure is 2,000rpm(40MPa). The maximum value of full-load torque capability is 25.5kgfm(based on 2,000rpm), and more than 90% compared to the level of the diesel engine were obtained. The DME vehicle was developed in this study, 120 km/h can drive to the stable, and calculated in accordance with the carbon-balance method of fuel consumptions is 5.7 km/L.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.8
• /
• pp.991-998
• /
• 2013

The fuel injection pipe of a common rail system used in a clean diesel vehicle plays a role in supplying fuel from a rail to the injector of each cylinder connecting the engine under a repeated internal pressure. The fuel injection pressure is increased to over 200 MPa for satisfying EU emission standards and improving fuel efficiency, and a heading process and an autofrettage process are required for preventing folding defects and improving fatigue life. In this study, the flow stress and SN data of the material of the pipe are obtained through a tensile test and a fatigue test. The heading process for checking the folding defects of pipe ends is performed by using FEA. Furthermore, the optimal design of the autofrettage process for improving fatigue life considering not only the compressive residual stresses of the inner surface but also the tensile residual stresses of the outer surfaces of the pipe under the repeated internal pressure is performed by using FEA. To verify the process design, fatigue analysis for the autofrettaged pipe is performed.