• 한국분무공학회지
• /
• 제22권2호
• /
• pp.87-95
• /
• 2017

Recently, as the interest in environmental issues have increased around the world, the regulation on vehicle exhaust have been tightened in each country. To satisfy such tightened exhaust regulation, automotive manufactures are forced to equipped Diesel Particulate Filter (DPF) at Diesel vehicles. If DPF is used for a long time, DPF regeneration should be performed. The objective of this study is to research on post injection for DPF regeneration. The result of the study was that it was desired that retarding post injection timing, lower load of engine and smaller the amount of main fuel injection, for DPF regeneration. Oil dilution was tended to increase as load was lower, amount of post injection was increased, and post injection timing was retarded.

• 한국분무공학회지
• /
• 제17권3호
• /
• pp.113-120
• /
• 2012

It is being more serious problems that the pollutant and the greenhouse gas emitted from the internal combustion engines due to the increasing demand of automobiles. To counteract this, as one of the ways has been studied, GDI type engine, which is directly injected into the combustion chamber and burns by a spark ignition that chose the merits of both gasoline engine and diesel engine, was appeared. The combustion phenomena in this GDI engine is known to contribute to combustion stability, fuel consumption reduction and reductions of harmful substances of exhaust gas emission, when the fuel spray of atomization being favorable and the mixture formation being promoted. Accordingly, this study analyzed the affection of ambient temperature and fuel injection pressure to the fuel by investigate the visualization of combustion, combustion pressure and the characteristic of emission, by applying GDI system on the constant combustion chamber. As a result, as the fuel injection pressure increases, the fuel distribution in the combustion chamber becomes uniform due to the increase of penetration and atomization. And when ambient temperatures in the combustion chamber become increase, the fuel evaporation rate being high but the penetration was reduced due to the reduction of volume flux, and confirmed that the optimized fuel injection strategy is highly needed.

• 한국분무공학회지
• /
• 제1권2호
• /
• pp.16-23
• /
• 1996

In case of a high-speed D.I. diesel engine. the injected fuel spray is unavoidable that the impinging on the wall of piston cavity and in this case the geometry of piston cavity has a great influence on the atomization structure and air flow fields. In the field of combustion and in many other spray applications, there are clear evidence of correlation between spray structure and emission of pollutants. Ordinary, the combustion chamber of driving engine have unsteady turbulent flow be attendant on such as the change of temperature, velocity and pressure. So the analysis of spray behavior is difficult. In this study, a single spray was impinged on each cavity wall at indicated angle in a quiescent atmosphere at room temperature and pressure, as being the simplest case, and 3 types of piston cavity such as Dish, Toroidal and Re-entrant type was tested for analyzing the influence of cavity geometry. And hot wire probe was used for analyze non-steady flow characteristics of impinging spray, and to investigate the behavior of spray, the aspects of concentration c(t), standard deviation $\sigma(t)$ and variation factor (v.f.) was measured with the lapse of time.

• 대한기계학회논문집A
• /
• 제39권9호
• /
• pp.909-916
• /
• 2015

본 연구는 디젤-과산화수소 에멀젼연료의 충돌분무를 대상으로 과산화수소의 혼합비가 증발분무 거동특성에 미치는 영향을 조사하였다. 에멀젼연료의 증발을 위해 온도조절이 가능한 가열판을 사용하여 온도를 $150^{\circ}C$, $200^{\circ}C$ 및 $250^{\circ}C$로 각각 설정하였고, 연료 분사압력을 400bar, 600bar, 800bar 및 1000bar로 설정하여 분사압력이 에멀젼연료의 증발특성에 미치는 영향을 확인하였다. 에멀젼연료의 혼합을 위 한 계면활성제로 span80과 tween80을 9:1의 비율로 혼합하여 에멀젼연료 전체 체적의 3%로 고정하였고 과산화수소의 혼합비율을 EF(Emulsified Fuel)0, EF2, EF12 및 EF22로 설정하여 디젤연료와 혼합하였다. 또한 에멀젼연료 증발 충돌분무의 가시화를 위해 슐리렌방법을 적용하였다. 본 연구의 결과로서 충돌하는 가열판의 온도와 분사압력이 높을수록 에멀젼연료 증발 촉진으로 연료 기상의 확산이 활발해지는 것을 알 수 있었다. 이러한 결과로부터 실제엔진에 에멀젼연료를 사용할 경우 연료 내 과산화수소 증발에 의한 연소실 온도 저하효과와 함께 보다 신속한 혼합기 형성은 엔진배출물의 감소를 일으키는 것으로 기대된다.

• 한국분무공학회지
• /
• 제17권2호
• /
• pp.57-63
• /
• 2012

For reduction of CO, NOx and soot emission emitted by diesel diffusion combustion, the authors focused on injection actuator to improve fuel availability inside combustion chamber. In this study, it was investigated the internal dynamic characteristics of two-stage injection with diesel injectors with different driving type for the common rail direct injection by using the AMESim simulation code. The analysis parameter defined such as fuel pressure, injection hole's diameter and driven voltage. As the results, it was shown that the piezo-driven injector had a faster response and had better control capability than the solenoid-driven injector. It was found the piezo-driven injector can be utilized effectively as multiple injector than solenoid-driven injector.

• 한국분무공학회지
• /
• 제22권4호
• /
• pp.190-196
• /
• 2017

The aim of this work is to investigate the combustion and exhaust emission characteristics of low-temperature combustion (LTC) at various EGR test conditions using a single cylinder common-rail diesel engine. In high EGR rate combustion mode with DME fuel, 30% (${\Phi}=0.61$) and 50% (${\Phi}=0.86$) of EGR were respectively examined, and then the combustion, exhaust emissions, nano-particle characteristics of each cases were measured. From these results, it revealed that The ignition delay and combustion duration are prolonged as the increase of EGR rate. In addition, at an advanced injection timing (BTDC $30^{\circ}$), ignition delays were fairly increased because the dilution effect of EGR and also low charge in-cylinder temperature created a lean mixture, thus decreased the peak release rate.

• 한국분무공학회지
• /
• 제10권3호
• /
• pp.45-53
• /
• 2005

The purpose of this study is to analyze that intake port swirl and fuel injection system have an effect on the engine performance in a turbocharged D.I. diesel engine of the displacement 9.4L. As result of steady flow test, when the valve eccentricity ratio moved to cylinder wall, the flow coefficient and swirl intensity is increased. And as the swirl is increased, the mean flow coefficient is decreased, whereas the Gulf factor is increased. Through this engine test, it can be expected to meet performance and emissions by the following applied parameters; the swirl ratio is 2.43, injection timing is BTDC 13oCA and compression is 15.5.

• 한국분무공학회지
• /
• 제12권3호
• /
• pp.166-171
• /
• 2007

Recently, many studies on HSDI diesel engines have been performed to reduce the fuel consumption and $CO_2$ emission. One of the prominent technique to reduce emission is a high pressure multiple injection. For this technique, the injection rate is a critical parameter in order to determine precise injection duration and timing for combustion control. Thus the purpose of this study was to investigate relationship between the injection rate and the time-signature of chamber pressure at different injection pressure conditions in a common rail direct injection type injector using the Zeuch method. Using the measured correlation constants, estimated fuel injection rates are presented at many different injection conditions.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.251-252
• /
• 2007

In this paper, in order to spray diesel fuel, multilayer actuator structured-ultrasonic nozzle and resonant inverter were manufactured. Multilayer actuator structured-ultrasonic nozzle as fabricated using PMN-PNN-PZT ceramics showing excellent piezoelectric characteristics. Its electrical and temperature properties were measured for investigating he applicability of stable ultrasonic nozle for spraying diesel fuel.

• 한국분무공학회지
• /
• 제26권3호
• /
• pp.142-148
• /
• 2021

The objective of this study is to analyze the basic flame behavior characteristics using the single fuel droplet combustion of diesel, palm-based biodiesel, and canola-based biodiesel. The results were compared and analyzed through the post processed image, which was applied the threshold level for removing noise in the raw image. The raw image was taken by a high-speed camera during the entire combustion process. At the same time, the maximum flame length, which was measured by the application code of the MATLAB program, the ignition delay, and the combustion period were compared and analyzed.