• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.7
• /
• pp.98-106
• /
• 2014

Emission standards for passenger diesel engines are becoming more and more stringent. Especially, Europe started the regulation of nano-particles from 2011 with EURO 5b. The objective of this study is to investigate the effect of fuel injection strategy on combustion and nano-particle emission in a small diesel engine. In this study, we conducted combustion analysis and measured both the weight of PM and number of nano-particels. At first, the optimum injection timing was determined with fixed engine operating conditions, such as engine speed, load, and fuel injection quantity. After that, the injection timing was controlled, and the effect of pilot injection was investigated. The number of nano-particles increased as engine load decreases, and it increased up to 10 times depending on the change of injection timing. The weight of PM emissions was increased at low load, and the PM emissions increased with increasing the number of pilot injections.

• Journal of Soil and Groundwater Environment
• /
• v.11 no.4
• /
• pp.10-17
• /
• 2006

Laboratory-scale two-dimensional aquifer physical model studies were conducted to assess the effect of air injection rate and air injection pattern on the removal of disel contaminated soil and groundwater by air/bio-sparging. The experimental results were represented that the optimal conditions in this experiment were as air injection rate of 1,000 ml/min and pulsed air injection pattern(15 min on/off). The results of the TPH reduction, DO consumption and $CO_2$ production indicate the effective biodegradation evidence of diesel. Based on our results, The minimal $O_2$ supply and pulsed air injection pattern could effectively enhance the diesel removal and the pulsing air injection had effect on oxygenation in this system. Thus, the cost of operating air/bio-sparging system will be reduced if optimal air injection rate and pulsed air injection pattern are applied to remediate contaminants.

• Journal of Environmental Health Sciences
• /
• v.32 no.5 s.92
• /
• pp.499-505
• /
• 2006

Bioventing efficiency was compared in a continuous and an intermittent(6hr injection and 6hr rest) air injection mode. Two lab-scale columns which packed with 5 kg of soil artificially contaminated by diesel oil were operated. The columns were maintained at the $25^{\circ}C{\pm}2.5$ in order to minimize the effect of exterior temperature variation. The flow rate of air injection mode were maintained constantly at the flow rate of 10 ml/min. The moisture of the columns was stably maintained at $60{\sim}80%$ of field capacity. The nutrient compounds were added to make C:N:P ratio as 100:10:l. The continuous and intermittent injection modes showed 67.56% and 69.63% reduction of initial TPH concentration during 90 days, respectively. Two venting modes showed similar results in the analysis of the trends of the hydrocarbon utilizing bacterial counts for operating periods. The carbon dioxide production rate of the continuous injection mode was higher than that of intermittent injection mode. The loss of diesel oil by volatilization in the continuous and intermittent injection modes were about 5% and 1%, respectively. The lower volatilization loss in the intermittent injection mode suggested that the biodegradation of TPH in the intermittent injection mode was greater than that of the continuous mode. These results suggested that the intermittent injection mode is more efficient than the continuous venting mode.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.115.2-115.2
• /
• 2010

Autothermal reforming(ATR) processes of hydrocarbon liquids such as diesel fuels are spotlighted as methods to produce hydrogen for Fuel cell. However, the use of heavy hydrocarbons as feedstocks for hydrogen production causes some problems which increase the catalyst deactivation by the carbon deposition. Coking can be inhibited by increasing the water dissociation on the catalyst surface. This results in catastrophic failure of whole system. Performance degradation of diesel autothermal reforming leads to increase of undesirable hydrocarbons at reformed gases and subsequently decrease the performance. In this study, perovskite-based catalysts were investigated as alternatives to substitute the noble metal catalyst for the ATR of diesel. The investigated perovskite structure was based on LaCrO3. and metals were added at the A-site to enhance oxygen ion mobility, transition metals were doped on the B-site to enhance the reformation. Substituted Lanthanum chromium perovskite were made by aqueous combustion synthesis, which can produce high surface area. And for the homogeneous fuel supply, we made ultrasonic injection system for reforming. We compared durability of evaporation system and ultrasonic system for fuel injection.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.12
• /
• pp.1655-1662
• /
• 2002

Recently, many researches have been performed to improve the performance of the combustion and emission in a D.I.Diesel engine. And many new techniques have been introduced and developed to reduce NO$_{x}$ and soot exhausted from diesel combustion. Some of these methods have the peculiar injection timing which is not used to traditional timing. To optimize these injection timing, characteristics of swirl flow and interaction of swirl with injection in the diesel engine should be investigated more carefully. Therefore, in this study, 2-zone energy method is adopted for the understanding of swirl flow in condition of moving piston, and then flame visualizations and image process are performed. From these studies, the characteristics of the swirl flow generated by SCV was investigated and the effect of swirl on injection timing was elucidated. As the results, velocity distribution caused by swirl flow increase the space utilization rate of flame plums. And flame plums of weak momentum are remained inside of combustion chamber by the swirl flow.w.

• 한국연소학회:학술대회논문집
• /
• 2003.12a
• /
• pp.231-236
• /
• 2003

HCCI(Homogeneous Charge Compression Ignition) combustion is an advanced combustion process explained as a homogeneously premixed charge of a fuel where air is admitted into the cylinder and compression ignited. It has possibility to reduce NOx by spontaneous auto-ignition at multiple points that allows very lean combustion resulting in low combustion temperatures. Particulate matters (PM) could be also reduced by the homogeneous combustion and no fuel-rich zones. Injection timing is extremely advanced to achieve homogeneous charge where a diesel fuel could not be vaporized sufficiently due to low pressure and low temperature condition. Also the over-penetration could be a severe problem. The small injection angle and multi-hole injectors were applied to solve these problems. Dimethyl ether (DME) as an altenative fuel was also applied to relive the bad vaporization problem associated with early injection of diesel fuel. Neat DME has a very high cetane rating and high vapor pressure. Contained oxygen reduces soot during the combustion. Experimental result shows DME can be easily operated in an HCCI engine. PM shows almost zero value and NOx is reduced more than 90% compared to direct-injection diesel engine operating mode but problem of early ignition needs more investigation.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.7
• /
• pp.80-88
• /
• 2021

The behavior of the injection system was determined through FFT and PSD analysis of the pressure data of the common rail, and when the diesel fuel is mixed with water, the pressure data of the common rail, depending on the water content and engine rotation speed, represent a different frequency component distribution. Recently, a theory has been suggested that mixing diesel fuel with water controls engine overheating, fuel efficiency, NOx, CO, etc., but if water content exceeds 10%, it can have a fatal adverse effect on the engine's injection system. In the future, it is necessary to promote fault diagnosis and prediction studies of diesel engines using FFT and PSD results from common rail pressure data.

• Journal of the korean Society of Automotive Engineers
• /
• v.7 no.2
• /
• pp.45-54
• /
• 1985

Recently, the problem of exhaust gas pollution is increasingly being aggravated by the active use of the Diesel engine. For the fuel-injection system which affects the composition of exhaust gas from the Bosch type single-hole nozzle in the Diesel engine, a mathematical model was set up to study pressure variations in the high pressure pipe, the injection rate, and the needle lift. The fundamental equations of the mathematical model have been solved by the Newton Raphson Method applying the Finite Diffrence Method. The effective stroke of the injection pump plunger due to a change in engine rpm was calculated by the measurement of Control Rack, Pinion, and Plunger sizes and by the use of Characteristic Curve of Governor. The computed results for the pressure variations in the high pressure pipe and needle lift at 800 rpm and 1000 rpm are in good agreement with experimental ones in general. By a developed program, the effects of other various parameters will by calculated for the performance of the fuel-injection system.

• Journal of ILASS-Korea
• /
• v.10 no.1
• /
• pp.10-16
• /
• 2005

To investigate the effect of shockwave on diesel spray characteristics under ultra high pressure injection, the velocity of spray tip and shock wave were investigated using the visualization of spray by schlieren method. Spray characteristics such as the spray radius, height, and droplets size were analyzed. It is found in this study that shock wave, produced by ultra high injection pressure, propagates faster than spray tip. Spray radius of right side of nozzle tip was shorter than that of left side and spray height of right side of nozzle tip was thicker than that of left side. Droplets sue was increased at 414MPa in injection pressure because of pressure gradient between inner and outer of tile spray caused by shockwave.

• International Journal of Automotive Technology
• /
• v.2 no.4
• /
• pp.123-133
• /
• 2001

An important goal in diesel engine research is the development of a means to reduce the emission of oxides of nitrogen ($NO_x$) and soot particulate. A phenomenological model based on the multizone concept is used in the current paper to analyze and compare the effects of exhaust gas recirculation (EGR) and split fuel injection on emission from a compression-ignited, direct-injection engine. The present results show that $NO_x$ can be reduced with a minimum penalty of soot particle emission with cooled EGR. Compared with EGR, split fuel injection has a higher soot penalty at a given level of $NO_x$ reduction.