• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.642-647
• /
• 1994

This paper describes some research works of computer-aided design of blanking & piercing progressive die for stator and rotor parts by the press. An approach to the system is based on knowledge based rules. The developed system is composed of five main modules such as input & graphic interface, blanking feasibility check, strip layout, die layout and output module. Using this system, design parameters (geometric shapes, die generated in dimensions and dimensions of tool elements) are determined and output is generated in graphic form. Knowledges for tool design are extracted from the plasticity theories, handbooks, relevent references and empirical know-hows of experts in blanking companies. The developed system provides powerful capabilities for process planning and die design of stator and rotor parts.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.418-422
• /
• 2005

In this study, the die design and die series on the surface residual stress of cold drawn eutectoid steel wire has been investigated. Test pieces were fabricated using die series with different mean and final reduction ratio. Surface residual stresses in the axial direction were measured by X-ray diffraction, Broker's 2-dimensional GADDS system. Results were compared with stress profiles which were calculated by 3D and 2D finite element simulation, Hibbitt's ABAQUS 6.4 program in Finite Element Analysis. By means of FEA method, optimal die shape considering delta-parameter were induced and applied in order to determine die sequence designs. Balance of the drawing stresses was also introduced to optimize die sequence.

• Transactions of Materials Processing
• /
• v.15 no.2 s.83
• /
• pp.153-157
• /
• 2006

In this study, the die design and die series on the surface residual stress of cold drawn eutectoid steel wire have been investigated. Test pieces were fabricated using die series with different mean and final reduction ratios. Surface residual stresses in the axial direction were measured by X-ray diffraction, Bruker's 2-dimensional GADDS system. The results were compared with stress profiles that were calculated by 3D and 2D finite element simulations, ABAQUS 6.4 program in finite element analysis(FEA). By means of the FEA method, optimal die shape considering delta-parameter were induced and applied in order to determine die sequence designs. Balance of the drawing stresses was also introduced to optimize die sequence.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.1
• /
• pp.33-41
• /
• 2010

This study was aimed at the design of the dies for the unified pipe joint of the intermediate shaft using the computer simulation to shorten the period of production, on the basis of the process planning which was designed by the field experts. In the computer simulation, 'Deform-3d' and 'eesy-DieOpt' have been used, which are the commercial process analysis and die design program. Through the process analysis, we could know the propriety of the forming process, the inner pressure of the die and the suitable fitting pressure between the insert and the sleeve which was not showing any positive tangential stresses in the insert. Through the simulation of die design, we could know the number of the stress ring, the diameter ratios, the stresses of the die, the shrink fitting tolerance and temperature in the condition of the already determined maximum outer die diameter of the multi-stage former. The validity of the die design using the computer simulation was analyzed by the experiments and the results were satisfactory. As the results of this study, the new and easy die design system for multi-forging has been developed.

• Transactions of Materials Processing
• /
• v.9 no.4
• /
• pp.413-420
• /
• 2000

In the die casting process, the flow of liquid metal has significant influence on the quality of casting products and die life. For the optimal process design of front housing part of aircon compressor, various analyses were performed in this study by using computer simulation code, MAGMAsoft. The simulation has been focused on the molten metal behaviors during the filling and solidification stages for the sound casting products. Two cases of casting design that have different types of gating system are considered in the analysis. The potential sites where the casting defects may occur is examined by computer simulation and an improved design process is proposed. Also the effect of partial squeeze on the quality of casting products is considered and the optimal time lag after filling process is determined. For the die-stability, the effect of operational parameters such as die temperature, heat cycle and spot cooling on the die life has also been analyzed.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.1
• /
• pp.135-143
• /
• 2003

This study presents development of a automatic design software for process and die design of hot extrusion of aluminium alloys through square dies. The design of extrusion dies is still an art rather than a science with increasing complexity of shape and thinness of section. Therefore, most of the die design is still dependent on personal judgement, intuition and experience. The objective of this study is to develop a software system which includes a design rule extracted from literatures and experts in the extrusion industry. The developed system is effectively used to design extrusion processes and dies with reduced lead time and trial extrusion.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.05a
• /
• pp.80-85
• /
• 2002

The progressive die for U-bending production part is a very specific division. This study reveals the Sheet metal forming process with multi-forming die by Center Carrier type feeding system. Through the FEM simulation by DEFORM it was accepted to u-bending process as the first performance to design in strip process layout design. The next process of die development was studied according to sequence of die development.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.77-81
• /
• 1999

The predictions of metal flow forging load optimal die angle and preform size are not so easy in turbine blade forging. First of all the quality of final product is influenced by side force which is one of the significant factors. in this study slab method is applied to determine optimal die angle minimizing side force and the position of preform Finally drawing of die design is obtained in optimal die angle with developing tool that is composed of Visual Basic.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.675-681
• /
• 2002

Parametric modeling and configuration design method are a important methods for rapid design in manufacturing. This paper proposes a relation rules which parametrically models a bonnet trimming tool based on Pro/Engineer. The concept of desogn is applied a trimming die of the bonnet outer panel. Trimming die have a many parameters. Each a parameter is related the die face and punch profile. A design system consists of a Pro/Engineer, a Pro/program.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.05a
• /
• pp.71-76
• /
• 2001

This paper describes a research work of developing system for conceptual die design system for Fine blanking. The method of approaching to the system is based on the knowledge-based rules. Knowledge for the system is formulated from experimental results and the empirical knowledge of field experts. This system has been written in VisualLISP on the AutoCAD using a personal computer and in Microsoft Visual Basic ver.6.0. Transference of data is accomplished by DXF (Drawing Exchange Format) method. This system consists of six modules, which are cognition of a drawing, cognition of shear length, calculation of shear force, materials properties database, determination of degree of difficulty of the product, determination of approximate life of punch and die modules. Results carried out in each module will provide efficiency to the designer and the manufacturer of die for Fine blanking. But the main focus of this system is the design of die for Fine blanking in the level of general concept. In order to use powerful tool in this field, developed system will be studied continuously.