• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.99-102
• /
• 1999

In this study, to investigate the effect of process variables such as reduction in area, semi-die angle and the rectangular ratio to the corner filling which influences the dimensional accuracy of the final product in the drawing of the cluadrangle rod from a round bar, it has been simulated by three dimensional rigid-plastic finite element method. In order to reduce the number of simulation artificial neural network has been introduced. Also, through the experimental investigation, the present results have been implemented on the industrial product. In results, the main process variable is the combination of the semi-die angle in case of the irregular shaped drawing process and reduction in area in the event of regular shaped drawing process, respectively.

• Journal of the Korean Society of Safety
• /
• v.15 no.4
• /
• pp.28-34
• /
• 2000

Copper clad aluminum composite materials are being used for economic and structural purposes, The development of an efficient production method of copper clad aluminum composite material rods by extrusion is very important. This paper describes experimental investigations in the direct extrusion of copper clad aluminum rods through conical dies. There are several parameters that have an influence on determining a sound clad extrusion. These variables are extrusion temperature, extrusion ratio, semi-cone angle of die, extrusion force, extrusion velocity, friction of between the container and billet, percentage of copper used and ratio of flow stress of copper to aluminum. In order to investigate the influence of extrusion temperature, extrusion ratio, semi-cone angle of die on the hot direct extrudability of the copper clad aluminum composite material rods, the experimental study have been performed with these variation.

• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.759-765
• /
• 2000

A composite material consists of two or more different material layers. Copper clad aluminum composite materials are being used for economic and structural reasons. This study is concerned with experimental investigation in the direct extrusion of copper clad aluminum rods through conical dies. The suggestion are given for the proper extrudability of copper clad aluminum rods via hot direct extrusion. This paper presents the variation of flow state and hardness at a variable of extrusion ratio and semi-angle of die. By measuring after and before extrusion radius ratio of Cu sleeve and Al core, proportional flow state has been considered. And also by measuring hardness, through extrusion way, a variation of hardness has been considered.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.89-92
• /
• 2004

This paper is concerned with the drawing process of Al-Si wire. In this study, the finite-element model established in previous work was used to analyze the effects of various forming parameters, which included the reduction in area, the semi-die angle, the aspect ratio and the inter-particle spacing of the Si in drawing processes. The finite-element results gave the consolidation condition. From the results of analysis, the effects of each forming parameter were determined. It is possible to obtain the important basic data which can be guaranteed in the fracture prevention of Al-Si wire by using FEM simulation.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.463-466
• /
• 2005

Restoring ductility or removing residual stresses is a necessary operation when a large amount of cold working is to be performed, such as in a cold-forging or warm forging process. The advantage of annealing temperatures was investigated. After Hydrostatic Extrusion process, extruded materials were annealed at $200^{\circ}C,\;350^{\circ}C,\;450^{\circ}C$ for 1 hour. Microstructure of the annealed material was observed to make an understand about the difference in mechanical properties.

• Transactions of Materials Processing
• /
• v.10 no.1
• /
• pp.67-74
• /
• 2001

The cold forging process to produce a long-neck flange is investigated by using model material test. The two stage process with optimum design condition is examined using plasticine, which is suitable to model steel at room temperature. The similarity theory is employed to estimate the forging load of each sequence by strict application of similarity condition between steel(AISI 1015) and plasticine material The model test results are compared with the simulation results and shows good agreement. The proper forging process with least forming energy can be resulted in $25^{\circ}$ of extrusion semi-die angle.

• The Journal of Korean Academy of Prosthodontics
• /
• v.37 no.3
• /
• pp.383-394
• /
• 1999

The indirect technique for making cast restoration requires that dies be as accurate and durable as possible. Currently, stone is the most commonly used material for die. However, it has some problems such as the weakness in its strength and low abrasion resistance. Recently, epoxy resin die systems have become available. The purpose of this study was to examine two commercially available resin die systems and evaluate some characteristics for their clinical performance. This study evaluated the dimensional accuracy of epoxy resins and their wettability with impression materials. In this study, the first experiment was about dimensional accuracy of different die materials. The master model was made of stainless steel. 10 models were made of two epoxy resins (Die-epoxy, Tri-epoxy) and a die stone (Fujirock) each. Occlusal diameter (Dimension I), occluso-gingival height (Dimension II), and interabutment distance (Dimension III) were measured in each model. Next, the contact angles of die materials with impression materials were observed. The blocks were made of polyether, hydrophilic additional silicone, polysulfide impression materials. By drop-ping the same amount (0.05ml) of Tri-epoxy, Die-epoxy, and die stone on the blocks, 10 samples of each die material were made. After setting of materials, the contact angles were measured. The results of this study were as follows. 1. The expansion of stone die and the shrinkage of resin dies in occlusal diameter were observed, and stone and Tri-epoxy were expanded and Die-epoxy was shrinked in occluso-gingival height. There was little change among materials in interabutment distance (p<0.05). 2. In comparison with the master model Tri-epoxy had the least variation in measurement of the three die systems examined. Die-epoxy was next, and die stone showed the greatest variation. 3. The compatibility of die stone for polyether, hydrophilic additional silicone, polysulfide decreased in order, wherease epoxy materials had the decreased compatibility for polyether and polysulnde, hydrophilic additional silicone in order. It was not statistically different between polyether and polysulfide (p<0.05). 4. The contact angles of Tri-epoxy, Die-epoxy, die stone were getting bigger in order.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.7
• /
• pp.865-873
• /
• 2013

The deep drawing and ironing (DDI) process involving the use of a high-capacity horizontal press is used for manufacturing acompressed natural gas (CNG) pressure vessel. However, some variables of the DDI process have been determined based on the experiences of workers, and the short die life needs to be improved for manufacturing the pressure vessel withhighquality and lowcost. In this study, process variables such as the draw ratio, distance between dies, radius of rounding of drawing die, and angle of ironing die are chosen to enhance the reliability and improve the die life based on previous studies and experiences. The draw ratio limits at which no tearing or wrinkling occurs are determined using FEA, and the distances between dies, radius of rounding of drawing die, and angle of ironing die are optimized by the DOE method. The results of the optimal process variables are compared with those of the existing DDI process for verifying their effectiveness.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.391-396
• /
• 2000

Today most companies are designing their automobile shapes by using 3 dimensional CAD software, CATIA. And they used to design 2 dimensional press dies to do some elastic work on their products, but they are currently trying to make use of dimensional software, Pro-Engineer. In this case, they have to change the 3 dimensional product design data to the proper format data for the following process. This paper will show the data loss and the deformation during data transfer between CATIA and Pro-Engineer, and then suggest a solution for these problems. Product's surface will be automatically placed by automatic press tipping angle setting in CATIA to prevent the product from being stuck in the press die. The 2 dimensional section view which is based on the tipping angle setting is created by Z-map. And, to remove the data loss and the data deformation in pro-Engineer, the product surface are delivered to the next process after it is changed to the 2 dimensional Z-map curves in CATIA. finally, this paper suggests an algorithm to develop the automatic design program for the press layout which regenerates product shape surface from the previous process.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.6
• /
• pp.38-44
• /
• 2002

Today most companies are designing their automobile shapes by using 3 dimensional CAD software, CATIA. And they used to design 2 dimensional press dies to do some elastic work on their products, but they are currently trying to make use of 3 dimensional software, Pro-Engineer. In this case, they have to change the 3 dimensional product design data to the proper format data for the following process. This paper will show the data loss and the deformation during data transfer between CATIA and Pro-Engineer, and then suggest a solution for these problems. Product's surface will be automatically placed by automatic press tipping angle setting in CATIA to prevent the product from being stuck m the press die. The 2 dimensional section view which is based on the tipping angle setting is created by Z-map. And, to remove the data loss and the data deformation in Pro-Engineer, the product surface are delivered to the next process after it is changed to the 2 dimensional Z-map curves in CATIA. Finally, this paper suggests an algorithm to develop the automatic design program for the press layout which regenerates product shape surface from the previous process.