• Journal of the Korean Society for Heat Treatment
• /
• v.13 no.5
• /
• pp.318-323
• /
• 2000

The planarization of rough polycrystalline diamond films synthesized by DC arc discharge plasma jet CVD (chemical vapor deposition) was attempted using KrF excimer laser pulses. The effects of laser incidence angle and reaction gases (ozone and oxygen) on etching rate of diamond were studied. The temperature change of diamond and graphite with different laser fluences was calculated by computer simulation to explain the etching behavior of diamond films. The threshold energy density from the experiment for etching of pure crystalline diamond was about $1.7J/cm^2$ and fairly matched the simulation value. Preferential etching of a particular crystallographic plane was observed through scanning electron microscopy. The etching rate of diamond with ozone was lower than that with oxygen. When the angle of incidence was $80^{\circ}$ to the diamond surface normal, the peak-to-valley surface roughness was Significantly reduced from $20{\mu}m$ to $0.5{\mu}m$.

• The Korean Journal of Ceramics
• /
• v.4 no.1
• /
• pp.15-19
• /
• 1998

Defects formation of Chemical Vapor Deposition (CVD) diamond on $^4He^{2+}$ irradiation and after remote hydrogen plasma treatment(RHPT) were investigated by cathodoluminescence(CL). As calculated in the TRIM simulation, the light elements of $^4He^{2-}$ can be penetrated into the diamond bulk structure at 3~4 $\mu\textrm{m}$ depth. The effects of the implantation region were observed when 5 keV~20 keV electron energy (insight 0.3~4.0$\mu\textrm{m}$) of CL measurement was irradiated to diamond at temperature 80 K. After the RHPT, rehybridization of irradiation damaged diamond was studied. The intensity of 5RL center(intrinsic defect of C) was diminished. The 2.16 eV center (N-V center) occurring usually by annealing could not be seen after RHPT. The diamond was rehybridized by hydrogen radicals without etching and thermal degradation by the RHPT.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.5
• /
• pp.371-377
• /
• 1998

The plasma chemical vapor deposition is one of the most utilized techniques for the diamond growth. As the applications of diamond thin films prepared by plasma chemical vapor deposition(CVD) techniques become more demanding, improved fine-tuning and control of the process are required. The important parameters in diamond film deposition include the substrate temperature, $CO/H_2$gas flow ratio, total gas pressure, and gas excitation power. With the spectroscopic ellipsometry, the substrate temperature as well as the various parameters of the film can be determined without the physical contact and the destructiveness under the extreme environment associated with the diamond film deposition. Through this paper, the important parameters during the diamond film growth using $CO+H_2$are determined and it is shown that $sp^2$ C in the diamond film is greatly reduced.

• Korean Journal of Crystallography
• /
• v.6 no.1
• /
• pp.14-26
• /
• 1995

The growth mechanism of diamond thin films, deposited by Hot Filament CVD, was investigated through observation of changes in their surface morphology as a function of the substance temperature and deposition time. Amorphous carbon or DLC thin films were deposited at low substrate temperature. Diamond films consisting of square-shaped particles, whose surfaces are (100) planes, were deposited at an intermedate temperature. At high substrate temperatures, diamond films consisting of the particles showing both (100) and (111) plane were deposited. The (100) proferred orientation of the diamond films are believed to be due to a relatively high supersaturation during deposition, and the growth condition for the diamond films having (100) preferred orientation can be applied to the single crystal growth since no twins are generated on the (100) plane. The grain size of the diamond films did not change with increasing temperature and its increasing rate with increasing deposition time was the same irrespective of the substrate temperature. However, the nucleation density increased with substrate temperature and its increasing rate with deposition time was much higher for the films deposited at higher substrate temperature.

• Applied Chemistry for Engineering
• /
• v.5 no.1
• /
• pp.16-23
• /
• 1994

In an argon thermal plasma CVD system diamond of metastable state was synthesized on molydenum substrate and concentration ratio of methane to hydrogen. Diamond was relatively well obtained when surface temperature of substrate was $890^{\circ}C$ and concentration of methane ratio was 0.5 percents.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.67-74
• /
• 1998

Two kinds of polished and unpolished freestanding films prepared by DC plasma CVD method were impacted by SiC particles to understand erosion mechanism. Erosion damage caused by solid impact was characterized by surface profilometer, scanning electron microscopy and Raman spectroscopy. Gradually decrease of surface roughness and sharp reduction of crystallinity for unpolished CVD films were observed with increasing erosion time. It was found that smaller grains of the diamond were removed in early stage of erosion process and larger grains were eroded with further impingement. By introduction of re-growth method on polished diamond, further understanding of erosion mechanism was achieved. Most of the surface fractures were initiated at the grain boundary.

• Journal of the Korean Vacuum Society
• /
• v.2 no.3
• /
• pp.346-354
• /
• 1993

The diamond particles and films were deposited on Si and qurtz substrate for $CH_4-H_2$ mixed gas by using RF plasma CVD. The temperature of substrate and the thinkness of films deposited on Si substrate were uniformly kept up by inserting metal plate between substrate and substrate holder. On increasing the reaction pressure in the same discharge power, the morphologies of films were changed from well-defind films to micro-crystal or ball-like. When diamond films were deposited on Si substrate from $CH_4-H_2$ mixed gas, we obtained well-defined diamond films at lower concentration than 0.5 vol% of $CH_4/H_2$. The deposited diamond films were indentified by SEM, XRD and Raman spectroscopy.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.905-908
• /
• 2000

The growth properties of diamond grain were examined by Raman spectroscopy and microscope images. Diamond thin films were prepared on single crystal Si wafers by microwave Plasma chemical vapor deposition. Preparation conditions, substrate temperature, boron concentration and deposition time were controlled differently. Prepared diamond thin films have different surface morphology and grain size respectively Diamond grain size was gradually changed by substrate temperature. The biggest diamond grain size was observed in the substrate, which has highest temperature. The diamond grain size by boron concentration was slightly changed but morphology of diamond grain became amorphous according to increasing of boron concentration. Time was also needed to be a big diamond grain. However, time was not a main factor for being a big diamond grain. Raman spectra of diamond film, which was deposited at high substrate temperature, showed sharp peaks at 1334$cm^{-1}$ / and these were characteristics of crystalline diamond. A broad peak centered at 1550$cm^{-1}$ /, corresponding to non-diamond component (sp$^2$carbon), could be observed in the substrate, which has low temperature.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.32 no.4
• /
• pp.159-167
• /
• 2022

In the past few decade years, laboratory-grown diamonds, also known as synthetic diamonds usually, have become more and more prosperous in the global diamond market. There are two main crystal growth processes of the gem-quality laboratory-grown diamond, the high pressure and high temperature (HPHT) and chemical vapor deposition (CVD). Synthetic gem diamonds grown by the HPHT press have been commercially available since the mid-1990s. Today, significant amounts of gem-quality colorless HPHT laboratory-grown diamonds have been producing for the jewelry industry. In the last several years, the CVD laboratory-grown diamonds have been gaining popularity in the market. In 2021, the CVD production rose and there are expectations that the trend would move upward continuously. This article presents information about the current status of laboratory-grown diamonds, lower cost compared to natural diamonds, market share, color distribution, spectroscopic properties of laboratory-grown diamonds, and so on.

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.636-644
• /
• 1997

The effect of various processing parameters, in particular the substrate and filament temperature, on the nucleation of diamond has been studied for the hot filament CVD process with a negative bias on the substrate. As far as the substrate temperature was maintained around the critical temperature of 73$0^{\circ}C$, the nucleation of diamond increased with increasing filament temperature. The maximum nucleation density of ~ 2$\times$109/$\textrm{cm}^2$ was obtained under the condition of filament temperature of 230$0^{\circ}C$, substrate temperature of 75$0^{\circ}C$, bias voltage of 300V, methane concentration of 20%, and deposition time of 2 hours. This nucleation density is about the same as those obtained in previous investigations. For fixed substrate temperatures, the nucleation density varies up to about 103 times depending on experimental conditions. This result is different from that of Reinke, et al. When the substrate temperature was above 80$0^{\circ}C$, a silkworm~shaped carbon phase was co-deposited with hemispherical microcrystalline diamond, and its amount increased with increasing substrate temperature. The Raman spectrum of the silkworm-shaped carbon was the same as that of graphitic soot. The silkworm-shaped carbon was etched and disappeared under the same as that of graphitic soot. The silkworm-shaped carbon was etched and disappeared under the deposition condition of diamond, implying that it did not affect the nucleation of diamond.