• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.37 no.3
• /
• pp.196-213
• /
• 2001

A split beam ultrasonic transducer operating at a frequency of 70 kHz to use in the fish sizing echo sounder was developed and the acoustic radiation characteristics were experimentally analyzed. The amplitude shading method utilizing the properties of the Chebyshev polynomials was used to obtain side lobe levels below -20 dB and to optimize the relationship between main beam width and side lobe level of the transducer, and the amplitude shading coefficient to each of the elements was achieved by changing the amplitude contribution of elements with 4 weighting transformers embodied in the planar array transducer assembly. The planar array split beam transducer assembly was composed of 36 piezoelectric ceramics (NEPEC N-21, Tokin) of rod type of 10 mm in diameter and 18.7 mm in length of 70 kHz arranged in the rectangular configuration, and the 4 electrical inputs were supplied to the beamformer. A series of impedance measurements were conducted to check the uniformity of the individual quadrants, and also in the configurations of reception and transmission, resonant frequency, and the transmitting and receiving characteristics were measured in the water tank and analyzed, respectively. The results obtained are summarized as follows : 1. Average resonant and antiresonant frequencies of electrical impedance for four quadrants of the split beam transducer in water were 69.8 kHz and 83.0 kHz, respectively. Average electrical impedance for each individual transducer quadrant was 49.2$\Omega$ at resonant frequency and 704.7$\Omega$ at antiresonant frequency. 2. The resonance peak in the transmitting voltage response (TVR) for four quadrants of the split beam transducer was observed all at 70.0 kHz and the value of TVR was all about 165.5 dB re 1 $\mu$Pa/V at 1 m at 70.0 kHz with bandwidth of 10.0 kHz between -3 dB down points. The resonance peak in the receiving sensitivity (SRT) for four combined quadrants (quad LU+LL, quad RU+RL, quad LU+RU, quad LL+RL) of the split beam transducer was observed all at 75.0 kHz and the value of SRT was all about -177.7 dB re 1 V/$\mu$Pa at 75.0 kHz with bandwidth of 10.0 kHz between -3 dB down points. The sum beam transmitting voltage response and receiving senstivity was 175.0 dB re 1$\mu$Pa/V at 1 m at 75.0 kHz with bandwidth of 10.0 kHz, respectively. 3. The sum beam of split beam transducer was approximately circular with a half beam angle of $9.0^\circ$ at -3 dB points all in both axis of the horizontal plane and the vertical plane. The first measured side lobe levels for the sum beam of split beam transducer were -19.7 dB at $22^\circ$ and -19.4 dB at $-26^\circ$ in the horizontal plane, respectively and -20.1 dB at $22^\circ$ and -22.0 dB at $-26^\circ$ in the vertical plane, respectively. 4. The developed split beam transducer was tested to estimate the angular position of the target in the beam through split beam phase measurements, and the beam pattern loss for target strength corrections was measured and analyzed.

• The Journal of Korean Society for Radiation Therapy
• /
• v.27 no.2
• /
• pp.97-106
• /
• 2015

Purpose : This study evaluate the thermal changes caused by use of the chemoport for drug administration and blood sampling during radiofrequency hyperthermia. Materials and Methods : 20cm size of the electrode radio frequency hyperthermia (EHY-2000, Oncotherm KFT, Hungary) was used. The materials of the chemoport in our hospital from currently being used therapy are plastics, metal-containing epoxy and titanium that were made of the diameter 20 cm, height 20 cm insertion of the self-made cylindrical Agar phantom to measure the temperature. Thermoscope(TM-100, Oncotherm Kft, Hungary) and Sim4Life (Ver2.0, Zurich, Switzerland) was compared to the actual measured temperature. Each of the electrode measurement position is the central axis and the central axis side 1.5 cm, 0 cm(surface), 0.5 cm, 1.8 cm, 2.8 cm in depth was respectively measured. The measured temperature is $24.5{\sim}25.5^{\circ}C$, humidity is 30% ~ 32%. In five-minute intervals to measure the output power of 100W, 60 min. Results : In the electrode central axis 2.8 cm depth, the maximum temperature of the case with the unused of the chemoport, plastic, epoxy and titanium were respectively $39.51^{\circ}C$, $39.11^{\circ}C$, $38.81^{\circ}C$, $40.64^{\circ}C$, simulated experimental data were $42.20^{\circ}C$, $41.50^{\circ}C$, $40.70^{\circ}C$, $42.50^{\circ}C$. And in the central axis electrode side 1.5 cm depth 2.8 cm, mesured data were $39.37^{\circ}C$, $39.32^{\circ}C$, $39.20^{\circ}C$, $39.46^{\circ}C$, the simulated experimental data were $42.00^{\circ}C$, $41.80^{\circ}C$, $41.20^{\circ}C$, $42.30^{\circ}C$. Conclusion : The thermal variations were caused by radiofrequency electromagnetic field surrounding the chemoport showed lower than in the case of unused in non-conductive plastic material and epoxy material, the titanum chemoport that made of conductor materials showed a slight differences. This is due to the metal contents in the chemoport and the geometry of the chemoport. And because it uses a low radio frequency bandwidth of the used equipment. That is, although use of the chemoport in this study do not significantly affect the surrounding tissue. That is, because the thermal change is insignificant, it is suggested that the hazard of the chemoport used in this study doesn't need to be considered.

• Radiation Oncology Journal
• /
• v.20 no.2
• /
• pp.155-164
• /
• 2002

Purpose : A ginkgo biloba extract (GBE) has been known as a hypoxic cell radiosensitizer. Its mechanisms of action are increase of the red blood cell deformability, decrease the blood viscosity, and decrease the hypoxic cell fraction in the tumor. The aims of this study were to estimate the effect of GBE on fractionated radiotherapy and to clarify the mechanism of action of the GBE by estimating the blood flow in tumor and normal muscle. Materials and Methods : Fibrosarcoma (FSall) growing in a C3H mouse leg muscle was used as the tumor model. When the tumor size reached 7 mm in diameter, the GBE was given intraperitoneally at 1 and 25 hours prior to irradiation. The tumor growth delay was measured according to the various doses of radiation (3, 6, 9, 12 Gy and 15 Gy) and to the fractionation (single and fractionated irradiation) with and without the GBE injection. The radiation dose to the tumor the response relationships and the enhancement ratio of the GBE were measured. In addition, the blood flow of a normal muscle and a tumor was compared by laser Doppler flowmetry according to the GBE treatment. Results : When the GBE was used with single fraction irradiation with doses ranging from 3 to 12 Gy, GBE increased the tumor growth delay significantly (p<0.05) and the enhancement ratio of the GBE was 1.16. In fractionated irradiation with 3 Gy per day, the relationships between the radiation dose (D) and the tumor growth delay (TGD) were TGD $(days)=0.26{\times}D$ (Gy)+0.13 in the radiation alone group, and the TGD $(days)=0.30{\times}D$ (Gy)+0.13 in the radiation with GBE group. As a result, the enhancement ratio was 1.19 ($95\%$ confidence interval; $1.13\~1.27$). Laser Doppler flowmetry was used to measure the blood flow. The mean blood flow was higher in the muscle (7.78 mL/100 g/min in tumor and the 10.15 mL/100 g/min in muscle, p=0.005) and the low blood flow fraction (less than 2 mL/100 g/min) was higher in the tumor $(0.5\%\;vs.\;5.2\%,\;p=0.005)$. The blood flow was not changed with the GBE in normal muscle, but was increased by $23.5\%$ ( p=0.0004) in the tumor. Conclusion : Based on these results, it can be concluded that the GBE enhanced the radiation effect significantly when used with fractionated radiotherapy as well as with single fraction irradiation. Furthermore, the GBE increased the blood flow of the tumor selectively.

• Journal of Sericultural and Entomological Science
• /
• v.18 no.2
• /
• pp.65-78
• /
• 1976

The mulberry small weevil, Baris deplanata ROELOFS, has highly infested mulberry trees in Korea. As the damage caused by the mulberry small weevil in mulberry fields has been increased over the country since 1969, the authors has carried out a series of biological and controlling studies on the pest from 1971 to 1972. The results obtained are summarized as follows. 1. The adult weevil is elongate oval in shape with black in color and the probocis is long as usual in curculionidae. The size of adult female is 3.30${\pm}$0.04mm in length, 1.47${\pm}$0.04mm in width, and the length of proboscis is 1.25${\pm}$0.014mm, while adult male is 3.28${\pm}$0.06mm in length, 1.40${\pm}$0.04mm in width, and the length of proboscis is 1.30${\pm}$0.02mm. The antenna is geniculate consisting of 12 segments. The terminal sternite of the abdomen has a pointed tip in male but not in female. 2. The egg is long oval in shape, milky white in color, 0.51${\pm}$0.05mm in length and 0.32${\pm}$0.02mm in width. 3. The mature larva is cylindrical and light yellowow in color except the head of dark brown, and legless, 3.88${\pm}$0.06mm in length, 1.40${\pm}$0.02mm width, each segment bearing many wrinkless and short setae. 4. The pupa is long oval, milky white and exarate, 3.53${\pm}$0.09 in length, 1.40${\pm}$0.03mm in width. 5. Majority of the species has one generation through a year and overwinters as adult in xylem of withered branch and come out again from late April to early May in next year. But some of the female oviposit in the same year and the offsprings overwinter as larva (0.4%) or pupa (0.1%) 6. The eggs are mostly laid under the cork layer of withered branch and the number of eggs deposited by an adult female is 73.44${\pm}$8.74, the average egg-laying period is 33.88${\pm}$6.04 days. The incubation period is 11.69${\pm}$0.39 days, the larval period 45.04${\pm}$1.63 and the pupal period 11.05${\pm}$0.49 days. The period of adult's activity is 46.7${\pm}$5.90 days. 7. The larvae feed on the cambium under the bark and adults feed on the winter bud, the latent bud, the leaf stalk and the base of newly shoot. 8. An active period of adults was observed during the period of 4 months from April to July. However, the peak of adult-density occurred in the early May (in the fields of spring-prunning) and early to middle June(in the fields of summer-prunning). 9. There is a positive correlation between the density of larvae and diameter and length of the branches. 10. The pattern of distributions of the adult of mulberry small weevil is negative binomial distribution. 11. The chalcid fly was disclosed to be a natural enemy which was parasite on the larvae of mulberry small weevil and its parasitic ratio was 11.9%. 12. Phosvel D, Malix D, Salithion EC, DDVP EC, and Phosvel EC were effective for the control of adults and Satchukoto-S EC, and Salithio EC were effective for the control of larvae.

• Radiation Oncology Journal
• /
• v.14 no.3
• /
• pp.191-199
• /
• 1996

Purpose : To evaluate 5-year survival rate, patterns of failure and complications of cervical cancer treatment, fifty nine patients treated by curative radiotherapy for the uterine cervical cancer were analyzed retrospectively. Materials and Methods : From March 1986 to May 1990, fifty nine patients with histologically proven uterine cervical cancer were analyzed. According to FIGO stage, there were 2 patients ($3.4\%$) in stage Ib, 2 patients ($3.4\%$) in stage IIa, 31 patients ($52.5\%$) in stage IIb, 15 patients ($25.4\%$) in stage IIIb, 9 patients ($15.3\%$) in stage IV. External RT was per formed by 6 MVLINAC with daily 1.8 Gy, 5 times per week and followed by ICR. A point dose of ICR was calculated to 30-43.66 Gy (median: 34.6 Gy). These techniques delivered total A Point dose of 80.4 to 109.8 Gy (median: 85 Gy). Patients had been followed up from 2 to 110 months (median: 61 months) Results : The overall 5-year survival rate & disease free survival rate were $55.9\%$ and $55.0\%$ respectively. According to FIGO stage, the 5-year survival rate for less than IIa, IIb, IIIb, IV were $75.0\%$, $74.8\%$, $26.7\%$, $33.3\%$, respectively. In univariate analysis, the 5-year survival rate for stage IIb and below versus stage IIIa and above revealed $74.8\%$, $29.2\%$ respectively (P<0.005). According to the hemoglobin level during RT, the 5-rear survival rate of was $73.3\%$ for patients with Hg 10 gm/dL or higher, in contrast to $0\%$ for those with lower than 10 gm/dL (p<0.005). In 18 patients with nonbulky tumor (<5cm), the 5-year survival rates were $71.8\%$. The 5-rear survival rates for 18 patients with 5 cm or greater in tumor diameter were $22.2\%$ (p<0.005). The 5-year survival rate for Patient age of above 50 years and below were $65.3\%$ $34.2\%$ respectively (p<0.05). ECOG performance status. pathologic finding, total dose, total treatment time were not statistically significant factors. The significant prognostic factors affecting overall 5-year survival rate by multivariate analysis showed the hemoglobin level during RT (P=0.0001), tumor size (p=0.0390), FIGO stage (p=0.0468). Total recurrence rate was $23.7\%$ local failure $15.2\%$ (9/59), distant metastasis $6.8\%$ (4/59), local and distant metastasis $1.7\%$ (1/59). According to the RTOG/EORTC Soma Scales, the late complication rate was $23.8\%$ (14/59) The late complication rate of colorectum and genitourinary tract were $15.3\%$ (9/59), $8.5\%$ (5/59), respectively: 10 patients ($17.0\%$) were grade 2, 3 Patients ($5.1\%$) were grade 3 and one patient ($1.7\%$) was grade 4. The late complications were radiation proctitis, rectal bleeding, radiation colitis, diarrhea and radiation cystitis in decreasing order. Conclusion : For improvement of therapeutic results, prospective randomized trials are recomended to discover new prognostic factors and more aggressive radiation therapeutic methods are needed for poor prognostic patients. The adjuvant chemotherapy or radiation-sensitizing agents must be considered to inhibit regional and distant metastasis.

• Journal of Korean Society of Forest Science
• /
• v.78 no.3
• /
• pp.287-301
• /
• 1989

A tree of Ailanthus altissima Swingle was fastened with a plastic band, 19mm wide, around the stem 180cm above ground level and was left to grow under this condition for one year, By removal of this band the tumorous tissue gradually developed and the tree bearing distinct tumorous tissue, an overgrowth surrounding the stem, was harvested two years after the band removal. For the investigation of this tumorous part and its comparison with adjacent normal parts in the anatomical features of individual elements, the tumorous part and parts directly and 40cm above and below the tumorous part were obtained from the tree. The tumor wood having remarkably wider growth increment occurred in the 3rd growth ring the first year after removal of the fastened band, and the barrier zone which delimited the discolored wood from the normal-colored wood inwards appeared u1 the intra-2nd growth ring produced during the fastened period in the tumorous part and the false ring-like zones equivalent to barrier Zone were shown in the normal-colored 2nd growth rings of the parts directly and 40cm above and below the tumorous part, as well. The tumor wood, the 3rd growth ring, and proportion of the 2nd growth ring formed after barrier zone in the tumorous part shared common characteristics in the irregular growth ring boundary, misshapen and shorter individual fibers and vessel elements, and large ray widths and heights. The springwood pores were smaller in diameter in the tumor wood, and the larger radial and smaller tangential diameters of summerwood solitary pores and individual pores consisting of pore multiples in proportion of the 2nd growth ring formed after the barrier zone were transformed into near-isodiametric in the tumor wood, the 3rd growth ring, in the tumorous part. Only in proportion of the 2nd growth ring formed after the barrier zone were transformed into near-isodiametric in the tumor wood, the 3rd growth ring, in the tumorous part, ray densities greatly increased. And the massive tumor wood was caused not by cell size but by cell number because the radial and tangential diameters of fibers in the tumor wood, the 3rd growth ring, in the tumorous part were not sufficiently different from those in the same aged growth rings of the directly and 40cm above and below the tumorous part.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.2
• /
• pp.108-118
• /
• 2009

Statement of problem: Volume stability, microstructure reproducibility and fluidity along with compatibility with dental stone must be in consideration in order to use tissue conditioner as a material for functional impression. There are few studies concerning the influence of time factor in oral condition on surface roughness of the stone and optimal retention period in the oral cavity considering such changes in surface roughness. Purpose: The purpose of this study was to find out the influence of various kinds of tissue conditioner, its powder/liquid ratio and immersion time on surface roughness of the stone. Material and methods: Materials used in this study were the three kinds of tissue conditioners(Coe-Comfort, Visco-Gel, Soft-Liner) and were grouped into three: group R-mixed with standard powder/liquid ratio that was recommended by the manufacturers, group M-mixed with 20% more powder, group L-mixed with 20% less powder. Specimens were made with the size of 20 mm diameter and 2 mm width. Each tissue conditioner specimens were subdivided into 5 groups according to the immersion time(0 hour, 1 day, 3 days, 5 days, 7 days), completely immersed into artificial saliva and were stored under $37^{\circ}C$. Specimens of which the given immersion time elapsed were taken out and were poured with improved stone, making the stone specimens. Surface roughness of the stone specimens was measured by a profilometer. Results: Within the limitation of this study, the following results were drawn. 1. Major influencing factor on surface roughness of the stone model made from tissue conditioner was the retention period(contribution ratio($\rho$)=62.86%, P<.05) of the tissue conditioner in oral cavity to make functional impression. 2. In case of Coe-Comfort, higher mean surface roughness value of the stone model with statistical significance was observed compared to that of Soft-Liner and Visco-Gel as immersion time changes(P<.05). 3. In case of group L(less), higher mean surface roughness value of the stone model with statistical significance was observed compared to that of R(recommended) and M(more) group as immersion time changes(P<.05). Conclusion: We may conclude that as the retention period of time in oral cavity influences surface roughness of the stone model the most and as the kind of tissue conditioner and its P/L ratio may influence also, clinician should well understand the optimal retention period in oral cavity and choose the right tissue conditioner for the functional impression, thus making the functional impression with tissue conditioner usefully.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.26 no.1
• /
• pp.56-68
• /
• 1981

A maize line was selected in 1979 among 1000 Korean local maize lines collected in 1977. The selected maize line was characterized by having three to four tillers and eight to 10 ears on each individual plant. The line was assumed to have a great potential as a silage crop. The investigation was conducted as one of the serial studies on the Korean maize collected lines to provide basic information on the genetic variabilities of the multi-eared and tillered (MET) line and on other agronomic characters, prior to use the line as material for future breeding works for silage crop. The MET line and Suwon #19, single cross hybrid, as check variety were planted on May 1, 15 and 30, in three different levels of plant populations. The results obtained were summarized as follows: 1. The genetic variabilities of multi-ear and tillering habits were greater than environmental variabilities. 2. Total dry leaf weight of individual plant of MET line was also significantly higher than that of Suwon #19. 3. The mean number of tillers and ears bearing on the individual plant of MET line varied greatly with plant densities. The number of tillers and ears was on the average 2.9 and 7.0, respectively, when planted in 60cm. by 60cm. 4. The total dry matter and dried stem weight of the individual plant on MET line were comparable to those of Suwon #19. 5. The kernel weight from the individual plant of MET line was 5 to 40% less than that of Suwon #19, depending upon the plant densities. 6. The Kernel to stover ratio was higher for Suwon #19 than for the MET line. (41% to 35%). 7. The MET line had shown first tiller two weeks after planted on May 1. The second and third tillers appeared three to five days after the appearance of the first tiller. 8. The MET line was very specific in tillering habits. All the tillers were borne on the first few nodes of main stem below the soil surface. 9. The tillering habits of MET line were vigorous in the early part of the growing season, but less vigorous in the later part of the growing season. The number of efficient tillers bearing useable ears, was around two to three, when planted in 60cm. by 60cm. 10. The difference of plant height between main stem and first few tillers was around 10cm. 11. The ear size of MET line was around one-third of the major corn belt hybrids. The shape of ear of MET line was conical, with different diameter. 12. The kernel of the MET line was flinty with small soft starch patches on the endosperm part. 13. The 100 kernel weight was around 15gr., which is about one half of the major high yielding hybrids. 14. The ear height of MET line was comparatively higher than that of Suwon #19. 15. Significantly high and positive phenotypic correlation coefficients were obtained among major plant characters. 16. The growth rate of MET line was slower than that of Suwon #19. 17. MET line and Suwon #19 were both heavily infected with black streaked mosaic virus.

• Korean Journal of Agricultural Science
• /
• v.16 no.1
• /
• pp.84-101
• /
• 1989

An accurate measurement of size, surface area and volume of agricultural products is essential in many engineering operations such as handling and sorting, and in heat transfer studies on heating and cooling processes. Little information is available on these properties due to their irregular shape, and moreover very little information on the rough rice, soybean, barley, and wheat has been published. Physical dimensions of grain, such as length, width, thickness, surface area, and volume vary according to the variety, environmental conditions, temperature, and moisture content. Especially, recent research has emphasized on the variation of these properties with the important factors such as moisture content. The objectives of this study were to determine physical dimensions such as length, width and thickness, surface area and volume of the rough rice, soybean, barley, and wheat as a function of moisture content, to investigate the effect of moisture content on the properties, and to develop exponential equations to predict the surface area and the volume of the grains as a function of physical dimensions. The varieties of the rough rice used in this study were Akibare, Milyang 15, Seomjin, Samkang, Chilseong, and Yongmun, as a soybean sample Jangyeobkong and Hwangkeumkong, as a barley sample Olbori and Salbori, and as a wheat sample Eunpa and Guru were selected, respectively. The physical properties of the grain samples were determined at four levels of moisture content and ten or fifteen replications were run at each moisture content level and each variety. The results of this study are summarized as follows; 1. In comparison of the surface area and the volume of the 0.0375m diameter-sphere measured in this study with the calculated values by the formula the percent error between them showed least values of 0.65% and 0.77% at the rotational degree interval of 15 degree respectively. 2. The statistical test(t-test) results of the physical properties between the types of rough rice, and between the varieties of soybean and wheat indicated that there were significant difference at the 5% level between them. 3. The physical dimensions varied linearly with the moisture content, and the ratios of length to thickness (L/T) and of width to thickness (W/T) in rough rice decreased with increase of moisture content, while increased in soybean, but uniform tendency of the ratios in barley and wheat was not shown. In all of the sample grains except Olbori, sphericity decreased with increase of moisture content. 4. Over the experimental moisture levels, the surface area and the volume were in the ranges of about $45{\sim}51{\times}10^{-6}m^2$, $25{\sim}30{\times}10^{-9}m^3$ for Japonica-type rough rice, about $42{\sim}47{\times}10^{-6}m^2$, $21{\sim}26{\times}10^{-9}m^3$ for Indica${\times}$Japonica type rough rice, about $188{\sim}200{\times}10^{-6}m^2$, $277{\sim}300{\times}10^{-9}m^3$ for Jangyeobkong, about $180{\sim}201{\times}10^{-6}m^2$, $190{\sim}253{\times}10^{-9}m^3$ for Hwangkeumkong, about $60{\sim}69{\times}10^{-6}m^2$, $36{\sim}45{\times}10^{-9}m^3$ for Covered barley, about $47{\sim}60{\times}10^{-6}m^2$, $22{\sim}28{\times}10^{-9}m^3$ for Naked barley, about $51{\sim}20{\times}10^{-6}m^2$, $23{\sim}31{\times}10^{-9}m^3$ for Eunpamill, and about $57{\sim}69{\times}10^{-6}m^2$, $27{\sim}34{\times}10^{-9}m^3$ for Gurumill, respectively. 5. The increasing rate of surface area and volume with increase of moisture content was higher in soybean than other sample grains, and that of Japonica-type was slightly higher than Indica${\times}$Japonica type in rough rice. 6. The regression equations of physical dimensions, surface area and volume were developed as a function of moisture content, the exponential equations of surface area and volume were also developed as a function of physical dimensions, and the regression equations of surface area were also developed as a function of volume in all grain samples.

• Korean Journal of Agricultural Science
• /
• v.9 no.1
• /
• pp.396-450
• /
• 1982

To obtain basic information on the Korean local corn lines a total of 57 lines were selected from 1,000 Korean local collection at Chungnam National University, classified by principal component analysis, and genetic nature was investigated. The results are summarized as follows. 1. There were a great variation in mean values of plant characters of the lines. The mean values of plant characters except for density of kernels varied with types of crossing. All characters except. for tasselling dates were reduced in magnitude when selfed, while those characters were increased when topcrossed. 2. The correlation coefficients among characters studied ranged front 0.99 to -0.59. The correlation coefficients among characters were not greatly changed depending upon types of crosses. 3. In order to classify the lines more effectively, selected 12 plant characters were used to classify 57 local lines by principal component analysis. The first four component could explain 86.4%, 83.4% and 81.1% of the total variations in sibbed lines, selfed lines and topcrossed lines, respectively. 4. Contribution of characters to principal component was high at upper principal components and low at lower principal components. 5. Biological meaning of the principal component and plant types corresponding to the each principal component were explained clearly by the correlation coefficient between principal components and characters. The first principal component appeared to correspond to the size of plant and ear. The second principal component appeared to correspond to the degree of differentiation in organs and the duration of vegetative growing period. But biological meaning of the third and fourth principal components was not clear. 6. The lines were classified into 4 lineal groups by the taxonomic distance. Group I included 52 lines which was 91.2% of total lines, group II 3 lines, group III 1 lines and group IV I lines, respectively. Four groups could be characterized as follows : Group I : early maturity, short-culmed, medium height plant, small ears, medium kernels and medium yielding. Group II : late maturity, medium height plant, small ears, small kernels, prolific ears and higher yielding. Group III : medium maturity, tall-culmed, small ears, small kernels and low yielding. Group IV : medium maturity, tall-calmed, large ears, one ear plant and me yielding. 7. The inbreeding depression varied with plant characters and lines. The characters such as yield, kernel weight per ear, ear weight and plant height showed great degree of inbreeding depression. Group I showed high inbreeding depression in such characters as 100 kernel weight, leaf number, plant height and days to tasselling, while group II showed high inbreeding depression in other plant characters. 8. Heterosis of plant characters varied also with lines. The ear weight, kernel weight per ear, yield, 100 kernel weight, and plant height were some of the plant characters showing high heterosis. Group II showed high values of heterosis in such characters as ear length, ear diameter, ear weight, kernel weight per ear, 100 kernel weight, and leaf length, while group I was high in heterosis in other plant characters. 9. The degree of homozgosity was highest in ear weight (79.1%) and lowest in ear number per plant (-21%). Group II showed higher degree of homozygosity than group I. 10. Correlation coefficients between characters of ribbed and topcrossed lines were positive for all characters. Highly significant. correlation coefficients between ribbed and topcrossed lines were obtained especially for characters such as ear number per plant, plant height, leaf length and yield per plot.