• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.34 no.1
• /
• pp.9-13
• /
• 2011

The purpose of this study was to investigate the effects of the secondary tasks such as sending text message (STM) and searching navigation (SN) on skin conductance level (SCL) and deviation of vehicle speed during driving. The participants included 30 healthy adults; 14 males aged $25.2{\pm}0.9$ with $1.9{\pm}1.8$ years of driving experiences and 16 females aged $22.6{\pm}1.9$ with $1.2{\pm}0.8$ years of driving experiences. All subjects were instructed to keep a constant speed (80km/h or 100km/h). SCL and deviation of vehicle speed were measured during driving only and driving with secondary tasks. SCL and deviation of vehicle speed were more increased during the driving with secondary tasks than driving only. Secondary tasks increased an activation of sympathetic nerve system and decreased driving performance. However, there were no significant differences in the SCL and deviation of vehicle speed according to gender and speed.

• Journal of Biomedical Engineering Research
• /
• v.38 no.1
• /
• pp.32-42
• /
• 2017

The aim of this study was to evaluate driving performance of Healthy and disabled groups (with or without driver's license) to control steering wheel by using steering assistive devices in the driving simulator. The persons with partial loss of use of all four limbs have problems in operation of the motor vehicle because of functional loss to operate steering wheel. Therefore, if steering assistive devices for grasping the steering wheel are used to control the vehicle on the road in persons with disabilities, the disabled persons can improve mobility in their community life by driving a motor vehicle safely. Ten healthy subjects (with or w/o driver's license) and ten subjects with physical disabilities (with or w/o driver's license) were involved in this study to evaluate driving performance to operate steering wheel by using four types of steering assistive devices (Single-pin, V-grip, Palm-grip, Tri-pin) in driving simulator. STISim Drive 3 software was used to test the steering performance in four scenarios: straight road at low and high speed of vehicle (40 km/h and 80 km/h), curved road at low and high speed of vehicle (40 km/h and 80 km/h). This study used two-way ANOVA in order to compare the effects of two factors (type of steering assistive device and subject group) in the three dependent variables of driving performance (the lateral position of vehicle, standard deviation of lateral position representing the variation of the left and right movement of the vehicle and the number of line crossing). The mean values of the three dependent variables (lateral position, standard deviation of lateral position, the number of line crossing) of steering performance were statistically significantly smaller for the healthy or disabled groups with driver's license than the other groups without driver's license on the curved road at high speed of vehicle compared to low speed of vehicle.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.529-538
• /
• 2009

A trial run of locally-developed tilting train has been in process on Chungbuk line since the test vehicle was first produced. For the system stabilization, interface verification among the systems including track, structure, catenary and signaling system, not to mention the rolling stock, is very crucial. Therefore, in this study, the dynamic rail force of the tilting (Hanvit 200), high-speed (KTX) and general (Mugunghwa) vehicle caused by driving in transition curve track was measured. And, it compared the tilting response with the other by using the measured wheel load data in transition curve track, and then evaluated probability the range of wheel load fluctuation for the variable dynamic vertical and lateral wheel load. As a result, a range of wheel load by occured a change of cant from the high-speed and general vehicle which had fixed bogie structure was distributed throughout small deviation (${\Delta}8{\sim}13kN$). Otherwise, in case of the tilting train which was consisted of the pendulum bogie structure was distributed wide range about large deviation (${\Delta}25{\sim}28kN$) by changed of cant.

• Smart Structures and Systems
• /
• v.21 no.5
• /
• pp.571-582
• /
• 2018

Track irregularities of high-speed Maglev lines have significant influence on ride comfort. Their adjustment is of key importance in the daily maintenance of these lines. In this study, an adjustment method is proposed and track irregularities analysis is performed. This study considers two modules: an inspection module and a vehicle-guideway coupling vibration analysis module. In the inspection module, an inertial reference method is employed for field-measurements of the Shanghai high-speed Maglev demonstration line. Then, a partial filtering, integration method, resampling method, and designed elliptic filter are employed to analyze the detection data, which reveals the required track irregularities. In the analysis module, a vehicle-guideway interaction model and an electromagnetic interaction model were developed. The influence of the measured line irregularities is considered for the calculations of the electromagnetic force. Numerical integration method was employed for the calculations. Based on the actual field detection results and analysis using the numerical model, a threshold analysis method is developed. Several irregularities modalities with different girder end's deviations were considered in the simulations. The inspection results indicated that long-wavelength irregularities with larger girder end's deviations were the dominant irregularities. In addition, the threshold analysis of the girder end's deviation shows that irregularities that have a deviation amplitude larger than 6 mm and certain modalities (e.g., M- and N-shape) are unfavorable. These types of irregularities should be adjusted during the daily maintenance.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.20 no.5
• /
• pp.75-82
• /
• 2021

The number of traffic accidents is about 230,000, and due to non-recurring congestion and high driving speed, the number of deaths per traffic accident on freeways is more than twice compared to other roads. Currently, traffic information is provided based on nodes and links using the centerline of the road, but it does not provide detailed speed information. Recently, installing sensors for vehicles to monitor obstacles and measure location is becoming common not only for autonomous vehicles but also for ordinary vehicles as well. The analysis using large-capacity location-based data from such sensors enables real time service according to processing speed. This study presents an mapping method for individual vehicle data analysis based on space. The processing speed of large-capacity data was increased by using method which applied a quaternary notation basis partition method that splits into two directions of longitude and latitude respectively. As the space partition was processed, the average speed was similar, but the speed standard deviation gradually decreased, and decrease range became smaller after 9th partition.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.2
• /
• pp.74-84
• /
• 2022

Vehicle average speed information which measured at a point or a short section has a problem in that it cannot accurately provide the speed changes on an actual highway. In this study, segment separation method based on vehicle big data for accurate micro-speed estimation is proposed. In this study, to find the point where the speed deviation occurs using location-based individual vehicle big data, time and space mean speed functions were used. Next, points being changed micro-scale speed are classified through gradual segment separation based on geohash. By the comparative evaluation for the results, this study presents that the link-based speed is could not represent accurate speed for micro-scale segments.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.20 no.6
• /
• pp.47-54
• /
• 2021

The number of freeway traffic accidents in Korea is about 4,000 as of 2020, and deaths per traffic accident is about 3.7 times higher than other roads due to non-recurring congestion and high driving speed. Most of the accident types on freeways are side and rear-end collisions, and one of the main factors is hazard traffic flow caused by merge, diverge and accidents. Therefore, the hazard traffic flow, which appears in a continuous flow such as a freeway, can be said to be important information for the driver to prevent accidents. This study tried to classify hazard traffic flows, such as the speed change point and the section where the speed difference by lane, using individual vehicle information. The homogeneous segment of speed was classified using spatial separation based on geohash and space mean speed that can indicate the speed difference of individual vehicles within the same section and the speed deviation between vehicles. As a result, I could extract the diverging influence segment and the hazard traffic flow segment that can provide dangerous segments information of freeways.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.3
• /
• pp.238-245
• /
• 2001

This paper describes a method for detecting a close leading vehicle using the contour of the vehi-cles rear wheels. The contour of a leading vehicles rear wheels in 속 front road image from a B/W CCD camera mounted on the central front bumper of the vehicle, has vertical components and can be discerned clearly in contrast to the road surface. After extracting positive edges and negative edges using the Sobel op-erator in the raw image, every point that can be recognized as a feature of the contour of the leading vehicle wheel is determined. This process can detect the presence of a close leading vehicle, and it is also possible to calculate the distance to the leading vehicle and the lateral deviation angle. This method might be useful for developing and LSA (Low Speed Automation) system that can relieve drivers stress in the stop-and-go traffic conditions encoun-tered on urban roads.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.1074-1079
• /
• 2011

This paper describes the influence on the nonlinear critical speed results of a specific railway vehicle depending on various constraint conditions. In the roller-rig tests, proper constraints are inevitable to safely hold the test vehicles. Particularly, the test results using KRRI roller-rig are more sensitive to constraint conditions because it is a kind of semi-full car type. In this study, nonlinear critical speed of specific vehicle with regards to several constraint cases were predicted by computational analysis and these results were compared to find the suitable constraint conditions. And also the deviation of semi-full car model from actual full car model was investigated. According to the bifurcation analysis, the nonlinear critical speed are dependent with the constraint condition and car-body yaw motion should be free to achieve more accurate results. And the difference between semi-full and full car model was so small that KRRI's semi-full car model are valid as long as the stability is concerned.

• Proceedings of the KOR-KST Conference
• /
• 2007.02a
• /
• pp.306-314
• /
• 2007

This paper is to develop a model for evaluation of highway alignment design considering the driver's behavior in order to enhance the highway safety. Under the conditions, this research included a new evaluation criteria development and an analysis on how to change evaluation criteria according to roadway alignments, to evaluate safety. The vehicle spacing and speed deviation are suggested as new evaluation index The evaluation criteria model can be used to compare the anticipated safety performance of two or more geometric alternatives for a proposed highway improvement.