• 한국수소및신에너지학회논문집
• /
• 제21권3호
• /
• pp.207-213
• /
• 2010

Fuel consumption measurement of hydrogen fuel cell vehicle is considerably different from internal combustion engine vehicle such as carbon balance method. A practical method of fuel consumption measurement has been developed for hydrogen fuel cell vehicles. There are three method of hydrogen fuel consumption testing, gravimetric, PVT (pressure, volume and temperature), and mass flow, all of which necessitate physical measurements of the fuel supply. The purpose of this research is to measure the fuel consumption of hydrogen fuel cell vehicles on chassis-dynamometer and to give information when the research is intended to develop test method to measure hydrogen fuel economy.

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.194-202
• /
• 2014

Steering axis of suspensions is an important factor that affects ride and handling quality in the vehicle chassis development. Macpherson strut and double wishbone's steering axis are defined geometrically, but multi-link suspensions can not be geometrically analyzed. In this case instant axis theory is commonly used to find a steering axis. Since the steering axis is moving with varying caster and kingpin inclination angle, this method approximately corresponds with exact solution. In this paper, we propose a velocity analysis method to find a pure rotational axis of the wheel relative to suspension arms, that is exact solution of the steering axis. This paper extends the method to analyze the steering axis of multi-link suspensions with bushing compliance. The analysis results applied to double wishbone and multi-link suspensions demonstrate validity and accuracy of the proposed method.

• 한국자동차공학회논문집
• /
• 제11권4호
• /
• pp.37-43
• /
• 2003

The exhaust gas recirculation (EGR) is needed for one of various strategies to reduce NOx emission. But to get the proper EGR rate, the intake and exhaust system become complicated, also application of EGR system is difficult because of the penalty in fuel consumption and the increase in particulate matter. This study is focused on the development of EGR valve using the electrical method. The effects of EGR on the characteristics of NOx, CO, CO2 emissions and particulate mater have been investigated using small-displacement size 0.8-liters engine of diesel passenger car operating at several loads and speeds. After the analysis and comparison between conventional E-EGR valve and developed E-EGR valve performance by test bench, the estimation of vehicle application was executed through the EGR map and CVS-75 test result measured on the chassis dynamometer.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.83-83
• /
• 2009

The automotive chassis components are structural assemblies that support the engine, suspension, and steering components of the vehicle. For the development of AHSS components, the durability analysis is important. In this paper, the low cycle fatigue property of AHSS was evaluated for the geometry complex and local plasticity in the base material. The GMAW optimization was implemented for the weld soundness using the moving least square method. And the weld S-N curves of AHSS were evaluated to access durability analysis for the weld region. For the verification, the durability analysis of the couple torsion beam axle (CTBA) was performed and compared to the rig test result. The durability analysis using the low cycle fatigue property and the evaluated weld S-N curve of AHSS met the good agreement with the test result.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.928-933
• /
• 2001

EGR(Exhaust Gas Recirculation) is an effective strategy to control nitrogen oxides emissions from diesel engine. The EGR reduces $NO_x$ through lowering the oxygen concentration in the combustion chamber as well as through heat absorption. However, application of EGR system is difficult because of the penalty in fuel consumption and the increase in particulate matter. The engine used for the experimental was a 3-cylinder 0.8-liter turbo-charged light duty diesel engine with an electronic EGR valve. In this study, experiments were performed at variable vehicle speeds and loads on the chassis dynamometer. To evaluate the exhaust emissions with the EGR system testing was performed using cvs-75 mode test procedure. Results of the cvs-75 mode test achieve sufficiently to meet EURO3 standards.

• 한국소음진동공학회논문집
• /
• 제25권3호
• /
• pp.184-190
• /
• 2015

NVH engineering has become a hot issue due to radical technology changes and development in automotive industry since customers' expectations and needs for their vehicle is taken to a higher level. However, the source identification and quantification of the road noise within a vehicle is still not at the level where it needs to be to meet their expectations due to its' complex transfer path and difficulties in path optimization. The primary focus of this research is on direct force obtaining method at suspension hard points using suspension test rig. Directly obtained forces at suspension to body mounting points are critical and crucial for determining the effects of design changes of the suspension has on road noise performance. Direct force obtaining method has its limitation in sensor installation within an actual vehicle therefore, many has been indirectly calculating forces using full matrix inversion method or dynamic stiffness method. In this study, to circumvent this limitation, a suspension rig is used. Then, the suspension rig is verified through a comparative analysis of its dynamic behavior between the actual vehicle by cleat test on chassis dynamometer.

• 한국산학기술학회논문지
• /
• 제17권9호
• /
• pp.133-140
• /
• 2016

국토교통부에서는 교통약자의 이동 편의 증진을 위하여 승하차에 편리한 저상버스를 도입하였다. 표준모델로 고시된 저상버스는 11 m 급, 압축천연가스(CNG, Compressed Natural Gas)를 사용하는 차량으로 개발되었다. 11 m 급 저상버스는 길이 좁은 농어촌 및 산간지역 도로여건에서의 운행과, CNG 연료의 특성상 충전시설의 한계로 인하여 연료보급의 단점을 가지고 있다. 본 연구에서는 국토교통부에서 교통약자의 이동편의 증진을 위해 진행하는 중형저상버스 표준모델 기술개발 과제의 일환으로 (주)타타대우상용차에서 제작한 LF-40을 대상으로 공차(CVW, Curb Vehicle Weight), 반적차(HVW, Half Vehicle Weight), 적차(GVW, Gross Vehicle Weight) 3가지 중량조건으로 실도로 타행주행을 통하여 주행저항 값을 취득하였고, WHVC, NIER-06, 복합 에너지 소비효율 측정 대상차량 외 차량의 에너지 소비 효율을 측정하기 위한 시험 방법인 정속주행 (60 km/h)모드를 사용하였다. 시험 결과 공차상태의 연비가 가장 좋았으며, 대표적으로 WHVC 모드에서는 공차대비 반적차는 3.5 %, 공차대비 적차는 12 % 연비소모율의 차이를 보였다. 60 km/h 정속 주행모드에서는 다른 시험모드와 다르게 공차보다 반적차의 연비가 높은 것으로 측정되었다. 추후 배출가스 데이터의 분석이 필요할 것으로 판단된다.

• 한국자동차공학회논문집
• /
• 제18권6호
• /
• pp.130-137
• /
• 2010

Due to test facility and specialty, it is physically difficult to conduct the modal tests of large-sized structures such as truck, bus and airplane. So, in case of a large-sized truck, the mode analysis on a full vehicle model comprised of reliable cabin, frame, and deck has been generally performed. However, the reliability of overall vibrational characteristics of the analytic model has not been fairly guaranteed by the testified models of each subsystem owing to the existence of cab suspension and the nonlinear mounting between a chassis frame and a special deck system. In this paper, a method to find out the modal characteristics of a large-sized military truck is presented. New modal test equipment is developed to set the boundary conditions of three military truck variants as close as a free-free condition. And the mode analysis method using coupled structure and dynamic models is established to consider the above-mentioned dynamic non-linearities of the vehicle itself. The usefulness of the suggested method is verified by comparing with the modal test results. Finally, the modal parameters of the final variant are extracted using the proved analytic method.

• 한국산업정보학회논문지
• /
• 제29권1호
• /
• pp.31-48
• /
• 2024

글로벌 자동차 산업은 연결, 자율주행, 공유, 전동화 등의 주요 방향 아래 지속적으로 발전하고 있으며, 국내 자동차 산업 또한 기존의 전통적인 자동차 부품 제조로부터 미래 트렌드에 부합하는 전략적인 업의 전환을 꾀하고 있다. 본 연구에서는 2013년부터 2021년까지 산업통상자원부에서 지원한 미래 자동차 분야 연구개발 과제를 대상으로 토픽 모델링을 수행하였다. 해당 기간을 3개 기간으로 구분하여 주요 토픽의 변화를 분석하였다. 센서와 통신, 운전자 보조 기술, 배터리 및 전력 기술은 전 기간 동안 지속적인 주요 토픽으로 나타났으며, 고강도 경량 차체와 같은 주제는 1기에서만 관찰되었다. 한편, AI, 빅데이터, 수소 연료전지와 같은 주제는 2기와 3기에 점점 더 중요한 토픽으로 부상하였다. 또한, 토픽별 정부 투자액과 투자 증가율을 기준으로 각 기수별 집중 투자 분야를 분석하였다. 이러한 연구 결과는 향후 자동차 분야의 정책 수립 및 연구개발 전략 마련 시 기초 자료로 활용될 것으로 예상되며, 증거 기반의 정책 수립과 결정에 기여할 것으로 기대된다.

• 한국자동차공학회논문집
• /
• 제23권2호
• /
• pp.161-168
• /
• 2015

Recently, due to various environmental problems such as global warming, increases of international oil prices, exhaustion of resource, a paradigm of world automobile market is rapidly changing from conventional vehicles using internal combustion engine to eco-friendly vehicles using electric power such as EV, HEV, PHEV and FCEV. Generally, in order to measure fuel consumption and pollutant emissions of cars, chassis dynamometer tests are performed on various driving cycles before actual driving test. There are many driving cycles for performance evaluation of conventional vehicles. However, there is a lack of researches on driving cycle for EV. In this study, the urban driving cycle for performance evaluation of electric vehicles was developed. This study is composed of two parts. In the part 1, the urban driving cycle 'GUDC-EV(Gwacheon-city Urban Driving Cycle for Electric Vehicles)' was developed by using driving data, which were obtained through actual driving experiment, and statistic analysis with chronological table. In this paper part 2, in order to verify the developed driving cycle GUDC-EV, virtual EV platforms were configured and simulations were performed with actual driving data using In addition, simulation results were compared with existing driving cycles such as FTP-72, NEDC and Japan 10-15.