• Progress in Superconductivity
• /
• 제10권1호
• /
• pp.60-67
• /
• 2008

We present domestic efforts for superconducting fault current limiter (SFCL) application in the Korea Electric Power Corporation (KEPCO) grid and pending points at issue. KEPCO's decision to upgrade the 154 kV/22.9 kV main transformer from 60 MVA to 100 MVA cast a problem of high fault current in the 22.9 kV distribution lines. The grid planners supported adopting an SFCL to control the fault current. This environment friendly to SFCL application must be highly dependent upon the successful development of SFCL having specifications that domestic utility required. The required conditions are (1) small size of not greater than twice of 22.9 kV gas insulated switch-gear (GIS), (2) sustainability of current limitation without the line breaking by circuit breakers (CB) for maximum 1.5 seconds. Also, optionally, recommended is (3) the reclosing capability. Conventional resistive SFCLs do not meet (1) $\sim$ (3) all together. A hybrid SFCL is an excellent solution to meet the conditions. The hybrid SFCL consists of HTS SFCL components for fault detection and line commutation, a fast switch (FS) to break the primary path, and a limiter. This characteristic structure not only enables excellent current limiting performances and the reclosing capability, but also allows drastic reduction of HTS volume and small size of the cryostat, resulting in economic feasibility and compactness of the equipment. External current limiter also enables long term limitation since it is far less sensitive to heat generation than HTS. Semi-active operation is another advantage of the hybrid structure. We will discuss more pending points at issues such as maintenance-free long term operation, small size to accommodate the in-house substation, passive and active control, back-up plans, diagnosis, and so on.

• 대한기계학회논문집B
• /
• 제38권9호
• /
• pp.747-755
• /
• 2014

광자(Photon)이나 전자기파(Electromagnetic Wave) 등의 형태로 직접 열을 전달하는 특징을 가지고 있는 복사열전달은 중간 매질의 열전달 관여여부에 따라 표면복사(Surface Radiation)와 기체복사(Gas Radiation)의 형태로 구분될 수 있다. 본 연구에서는 원통 형상에서의 표면복사에 대해 미지의 복사물성치들을 역해석 방법을 이용해 역추정하였다. 이때, 효율적인 역해석을 위해 반발 입자 군집 최적화(Repulsive Particle Swarm Optimization, RPSO) 알고리즘을 역해석 기법으로 채택하였다. 이로부터 얻은 해의 수렴성과 정확도 등을 기존의 유전알고리즘(GA) 결과와 비교해 봄으로써, 표면복사 현상에 대한 역해석의 적용 가능성을 고찰하고자 하였다.

• 대한기계학회논문집A
• /
• 제41권3호
• /
• pp.187-192
• /
• 2017

본 논문에서는 탄소나노튜브 전왜성 복합소재(Nano-Carbon Piezoresistive Composite, NCPC)를 기반으로 하며, 3D 프린팅 공정을 활용하여 제작된 압력센서의 개발 진행 연구를 소개하였다. 압력센서의 성능을 향상시키기 위하여 센서전극을 외팔보 형태로 설계하였고 3D 프린팅 공정을 활용하여 소형전극을 제작하였다. 압력을 전기적 저항의 변화로 바꾸는 전왜성 센서의 전극은 2wt%의 다중벽 탄소나노튜브/에폭시 전왜성 복합소재로 제작하였다. 센서는 압력시스템에 용이하게 적용하기 위하여 파이프 플러그 캡에 삽입하여 제작을 하였으며, 실험실 환경에서 압력교정기를 활용하여 실험을 하였다. 외팔보 전극의 압력센서는 16,500kPa까지 선형적인 출력전압 특성을 보였으며, 이는 벌크형 전극의 압력센서 대비 약 200% 압력측정 성능 향상을 보였다.

• 보건의료산업학회지
• /
• 제1권1호
• /
• pp.125-137
• /
• 2007

The current hospital industry is showing relatively low profitability in comparison with other industries due to the low medical fees and high costs. Therefore, our government presented the direction of improvement through model execution and support of the specialized hospitals. However, it is estimated that the specialized hospitals also will show differentiated management performances in accordance with their specialized fields due to the characteristics of medical treatment. Therefore, this study had attempted an analysis on the financial index in accordance with the weight of medical treatment items for the rehabilitative medicine department among the whole hospital groups through getting out of analyzing financial indices of individual hospitals centered at their costs. For this p개pose, this study had carried out its research by partially reciting the study on the plan for utilizing participations of private health resources to expand rehabilitative medicine services into the private people of the Korea Health Industry Development Institute(KHIDI). As its results, it was shown that the stability, profitability, activity and productivity of hospitals with high weight of medical treatment for the rehabilitative medicine department were lower than those for the general hospitals. To support smooth operations of these hospitals 'with high weight of medical treatment for the rehabilitative medicine department or of specialized rehabilitation hospitals, it is judged that the plan such as the support for hospital management fund and the additional recognition on the rehabilitative fees, etc. together with the actualization of medical fees must be provided for the institutions which are providing rehabilitative medical services more than the fixed percentage and being equipped with the sufficient medical equipment and personnel to do them.

• 수산해양기술연구
• /
• 제24권4호
• /
• pp.172-179
• /
• 1988

A cartridge type hydraulic logic valve consists of simple two port valve whose poppet is closed or opened by means of pressure signal of a pilot line. Accordingly, the logic valve can be used not only for direction, flow and pressure control purpose but also for versatile function valve which enables all above mentioned functions. In addition, the valve has little internal leakage and pressure loss, superior response characteristics and easiness in making small block type valve. The above mentioned good performances being recognized recently, the logic valve has been used widely in the large scale hydraulic system such as a hydraulic press system, for the performance requirements of high speed operation and precise control characteristics. However, there are scarce reports until now, except for a few ones from Aachen Institute of Technology in West Germany, so it is necessary to be studied on development and investigation for practical application. This paper showed that the static and dynamic characteristics of a logic valve when the logic valve is used for directional control, to investigate the relations between the valve operating characteristics and the valve design conditions. From the above mentioned procedure, it was ascertained that the valve operation characteristics obtained by numerical analysis showed good agreements with experimental results. The representative results obtained are as follows; 1. During the valve is closing, the poppet velocity is almost constant in the logic valve. 2. The pilot pressure P sub(3) and the resistance R in the pilot line have much influences on the valve operation time. 3. Spring strength have not such a severe influence on the valve operating time. 4. The operation characteristics of the logic valve can be estimated with good accuracy comparatively by numerical analysis with the equations describing poppet motion.

• 대한교통학회지
• /
• 제24권2호
• /
• pp.139-145
• /
• 2006

본 논문에서는 보행-차량 충돌사고 시 보행자 사망 여부를 확률적으로 예측할 수 있는 모형을 개발하였다. 베이지안 신경망을 적용하여 보행자 사망확률모형을 개발하고, 로지스틱 회귀분석 기법 기반의 모형과 예측력을 비교하였다. 본 연구를 위하여 개별 교통사고 자료를 수집하였으며, 교통사고 재현을 통해 사고 당시의 충돌속도를 추정하여 보행자 연령, 차종과 함께 모형의 독립변수로 사용하였다. 보다 정확하고 신뢰성 있는 모형개발을 위해 반복적 샘플링기법을 적용하여, 다양한 학습자료 및 테스트 자료를 구성하고 모형의 성능을 평가하였다 본 연구를 통해 개발된 모형은 보행자 보호를 위한 첨단차량기술 개발, 제한속도의 설정 등 다양한 정책 및 관련기술의 개발을 지원하는 유용한 도구로 사용될 것으로 기대된다.

• 기술혁신연구
• /
• 제22권3호
• /
• pp.261-286
• /
• 2014

막대한 예산이 투입된 정부연구개발사업에 대한 성과창출과 관리 등에 대해서 근래에 관심이 집중되고 있다. 이 연구에서는 정부연구개발사업의 혁신 및 사업화 성과 창출 경로를 추정할 수 있는 연립방정식 모형을 설계하여 산업에 따른 성과창출의 특성을 분석하였다. 이를 위해서 KEIT 산업기술혁신사업의 성과활용현황조사 데이터를 활용하였으며, 정보통신(IT) 산업과 화학(CT) 산업을 대상으로 하였다. 이 연구의 결과는 다음과 같다. 모든 기업들은 정부지원금을 통해 개발된 기술을 특허를 통해 보호하고 혁신을 파급시키는 역할을 하고 있었으나, 특허를 사업화하는 것은 IT 산업에서는 중소기업, CT 산업에서는 대기업으로 나타났다. 복합산업 성격인 IT 산업의 중소기업은 기업의 자체적인 혁신노력이 추가적으로 필요한 반면에 CT 산업의 중소기업은 기술개발과 사업화 성과 향상에 있어서 협력연구 등의 지원이 효과적이었다. 이러한 결과는 정부연구 개발사업으로 창출된 성과를 향상시키기 위해서 정부 정책 및 과제 기획 시 산업별 기업별 특성에 따라 주안점을 달리 해야 한다는 것을 시사한다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.544-544
• /
• 2014

Energy harvesting technology, which scavenges electric power from ambient, otherwise wasted, energy sources, has been explored to develop self-powered wireless sensors and possibly eliminate the battery replacement cost for wireless sensors. Among ambient energy sources, vibration energy can be converted into electric power through a piezoelectric energy harvester. For the last decade, although tremendous advances have been made in design methodology to maximize harvestable electric power under a given vibration condition, the research in reliability assessment to ensure durability has been stagnant due to the complicated nature of the multiple failure modes of a piezoelectric energy harvester, such as the interfacial delamination, fatigue failure, and dynamic fracture. Therefore, this study presents the first-ever system reliability analysis for multiple failure modes of a piezoelectric energy harvester using the Generalized Complementary Intersection Method (GCIM), while accounts for the energy conversion performance. The GCIM enables to decompose the probabilities of high-order joint failure events into probabilities of complementary intersection events. The electromechanically-coupled analytical model is implemented based on the Kirchhoff plate theory to analyze its output performances of a piezoelectric energy harvester. Since a durable as well as efficient design of a piezoelectric energy harvester is significantly important in sustainably utilizing self-powered electronics, we believe that technical development on system reliability analysis will have an immediate and major impact on piezoelectric energy harvesting technology.

• 한국산학기술학회논문지
• /
• 제15권8호
• /
• pp.5095-5108
• /
• 2014

본 연구는 임상연구코디네이터와 함께 임상시험을 수행하는 연구자 및 임상시험모니터요원이 인식하는 임상연구코디네이터의 역할수행 정도를 비교분석하기 위한 조사연구이다. 본 연구의 자료는 2011년 3월 7일부터 11월 30일까지 4개 병원의 연구자 39명과 임상시험모니터요원 68명을 대상으로 구조화된 설문지를 활용하여 수집하였고, 기술통계와 t-test를 이용하여 분석하였다. 연구자와 임상시험모니터요원 모두 임상시험에서의 임상연구코디네이터의 역할수행이 매우 중요하다고 인식하고 있었고, 그 중에서도 대상자 관리 업무에의 역할 수행 비중이 가장 높다고 인식하고 있었다. 그러나 각 항목별 역할수행 정도에 관해 연구자 집단과 임상시험모니터요원 집단 간 인식 정도를 비교해 보면 차이가 나타났다. 따라서 임상연구코디네이터의 역할수행에 대한 인력 간 인식 차이를 줄일 수 있는 보다 객관적인 임상연구코디네이터의 업무기술 및 지침 개발이 요구된다.

• 가정간호학회지
• /
• 제7권1호
• /
• pp.73-82
• /
• 2000

Twenty-first century coming of health care in our country is in a situation of much conflict because the relationship between nurses and doctors is seen in terms of a traditional and vertical structure. Accordingly. it is very difficult to find collaboration amongst individuals of these two professions. Now nursing is trying to find independence and autonomy by carrying out independent professional skills. This study on collaboration and the obstacles hindering its pursuit. The strategies of collaboration to give better health care quality are as follows; First, a program for professionals should be developed to enhance professional knowledge and technology and train nursing professionals so that nursing can be acknowledged as a profession with a power to carry out on independent job. Second, collaboration reduces expenses and results in satisfactory performances of duty, high productivity, low incidence of medical accident, and higher satisfaction of the patient. Therefore the leader in the higher position should take positive stance for collaboration and help create a cooperative situation through the development of practical orders for collaboration. opening cooperative wards, and meeting for collaboration. Third, a collaboration model should be introduced into the courses of the nursing and medical school curriculum, which would influence job atmosphere after graduation. Fourth, nurses should have pride in their jobs as professionals and have confidence in their professional skill, knowledge and ability. Nurses should make an effort to share responsibility and have independence and autonomy. Fifth, common people as well as doctors know little about professional practice and the role of nurses, so a publicity campaign is also required.