• 한국응용과학기술학회지
• /
• 제19권2호
• /
• pp.108-116
• /
• 2002

Experimental Study was carried out for benzene desorption by purge gas or evacuation in an activated carbon bed. As purge gas flow rate increased, desorption rate increased due to the higher interstitial linear gas velocity. For various purge gas flow rates, desoption curves almost got together if they were plotted against dimensionless time. At a higher flow rate, mass transfer zone became narrower. Temperature drop in the bed was more fast and severe at higher flow rates and higher outer temperature. It was found out that desorption was almost completed when the temperature in the drop of the bed returned to the initial temperature before temperature drop. Desorption by vacuum purge was completed in shorter time than desorption by purge gas. Countercurrent purge was more effective than cocurrent purge.

• 공업화학
• /
• 제17권2호
• /
• pp.201-209
• /
• 2006

활성탄과 제올라이트 13X를 충진시킨 흡착탑에 흡착질인 벤젠을 포화 흡착시킨 후 여러 가지 탈착 방법에 대한 효율을 살펴보았다. 뜨거운 수증기에 의한 탈착, 세정 기체에 의한 탈착, 진공에 의한 탈착 등을 실험하였고, 그 결과 뜨거운 수증기에 의한 탈착이 가장 좋은 탈착 방법으로 판단되었다. 또한 뜨거운 수증기는 흡착탑 내의 온도를 상승시키면서 탈착을 야기시키고 수증기 탈착 과정 이후에는 건조 공정이 수반되어야만 효율이 높아짐을 알 수 있었다. 건조 공정이 수반되지 않을 경우는 수증기가 추후에 흡착을 방해하는 결과를 초래하였다. 진공에 의한 탈착은 효과가 매우 적은 것으로 나타났는데 이로부터 벤젠의 경우에 압력 변화에 의한 탈착 보다는 온도 변화에 의한 탈착이 더 효과적인 것으로 판단되었다. 세정 기체에 의한 탈착에서는 진공 탈착과 함께 이루어질 때 좋은 탈착 성능이 나타남을 알 수 있었다.

• 한국수소및신에너지학회논문집
• /
• 제22권3호
• /
• pp.363-371
• /
• 2011

In this paper, a three-dimensional hydrogen desorption model is developed to precisely study the hydrogen desorption kinetics and resultant heat and mass transport phenomena in metal hydride hydrogen storage vessels. The metal hydride hydrogen desorption model, i.e. governed by the conservation of mass, momentum, and thermal energy is first experimentally validated against the temperature evolution data measured on a cylindrical $LaNi_5$ metal hydride vessel. The equilibrium pressure used for hydrogen desorption simulations is derived as a function of H/M atomic ratio and temperature based on the experimental data in the literature. The numerical simulation results agree well with experimental data and the 3D desorption model successfully captures key experimental trends during hydrogen desorption process. Both the simulation and experiment display an initial sharp decrease in the temperature mainly caused by relatively slow heat supply rate from the vessel external wall. On the other hand, the effect of heat supply becomes influential at the latter stages, leading to smooth increase in the vessel temperature in both simulation and experiment. This numerical study provides the fundamental understanding of detailed heat and mass transfer phenomena during hydrogen desorption process and further indicates that efficient design of storage vessel and heating system is critical to achieve fast hydrogen discharging performance.

• 한국대기환경학회지
• /
• 제27권2호
• /
• pp.191-200
• /
• 2011

A way to adsorptively remove indoor carbon dioxide at relatively lower concentration under ambient temperature was studied. A small lab-scale carbon dioxide adsorption and desorption reactors were prepared, and 5A and 13X zeolites were packed in this reactors to investigate their adsorption and desorption characteristics. The inflow carbon dioxide concentration was controlled to 5,000 ppm, relatively higher concentration found in indoor spaces with air quality problems, by diluting carbon dioxide with nitrogen gas. The flow rate was varied as 1~5 L/min, and the carbon dioxide concentration after this reactor was constantly monitored to examine the adsorption characteristics. It was found that 5A adsorbed more carbon dioxide than 13X. A lab-scale carbon dioxide desorption reactor was also prepared to investigate the desorption characteristics of zeolites, which is essential for the regeneration of used zeolites. The desorption temperature was varied as $25{\sim}200^{\circ}C$, and the desorption pressure was varied as 0.1~1.0 bar. Carbon dioxide desorbed better at higher temperature, and lower pressure. 5A could be regenerated more than three times by thermal desorption at $180^{\circ}C$. It is required to modify zeolites for higher adsorption and better regeneration performances.

• 대한환경공학회지
• /
• 제38권11호
• /
• pp.627-634
• /
• 2016

본 연구에서는 탄소폼 흡착소재를 이용하여 산업도금폐수로부터 중금속을 흡착 제거한 후 탈착용액을 이용하여 제거된 중금속을 용출하고 회수하는 과정의 특성을 평가해 보고자 하였다. 용액의 조성에 따른 복합 중금속의 탈착 특성을 살펴본 결과 증류수 조건에서는 용출이 관측되지 않았으며, 탈착용액으로 HCl과 $H_2SO_4 $를 이용한 경우 높은 중금속 농도를 나타내었다. 탈착 용액을 이용함과 더불어 물리적 기술인 초음파 처리를 이용한 경우 중금속의 용출이 증진되는 것을 확인하였으며, 초음파 장치의 출력이 높고 반응 시간이 길수록 효율도 증가하는 것으로 나타났다. 탄소폼 흡착소재를 구리도금 세척수 처리에 적용시켜본 결과 200 반응기부피(Bed volume) 동안 안정적인 제거 성능을 나타내었으며, 흡착된 구리는 탈착용액을 이용하여 용출시킨 후 직류 전원 장치를 이용하여 회수할 수 있었다. 또한 구리가 회수된 탈착용액은 재이용 효율은 84.2%로 나타났다.

• 청정기술
• /
• 제23권4호
• /
• pp.421-428
• /
• 2017

본 연구는 상용활성탄을 사용하여 산업공정에서 많이 사용되는 휘발성 유기화합물 중 톨루엔, 메틸에틸케톤(MEK), 이성분계(톨루엔-MEK)를 대상으로 흡착 및 탈착특성을 고찰하였다. 최적탈착온도를 설정하기 위해 온도별 탈착특성을 고찰하였고, 활성탄의 특성을 파악하기 위해 BET분석을 하였다. 상온에서 흡착실험을 진행하였고, $120^{\circ}C$까지 승온하여 탈착실험을 진행하였다. 이 실험을 10회 반복해서 진행하였다. 이를 통해 단일성분에서는 반복횟수가 많아질수록 흡착 및 탈착능이 줄어들며 활성탄과 상대적으로 친화력이 적은 MEK의 경우 톨루엔보다 낮은 흡착 및 탈착능을 보였다. 이성분계의 흡착 및 탈착 반복시험에서 친화력이 낮은 MEK가 먼저 파과되고 결과적으로 주입 농도보다 높은 농도로 탈착되었다.

• 한국광물학회지
• /
• 제22권4호
• /
• pp.289-295
• /
• 2009

카올리나이트 KGa-1b (표준 점토)의 인산염 탈착 특성을 규명하기 위하여 벳치(batch) 흡착-탈착 실험을 실시하였으며, 탈착 과정은 연속추출법에 따라 pH 4에서 시행하였다. 인의 함량은 UV 분광분석기를 시용하여 측정하였으며, 이 때 파장은 820 nm를 이용하였다. 카올리나이트의 인산염 흡착-탈착 반응은 비가역적으로 일어나며, 흡착된 대부분의 인산염은 고착되는 경향을 나타낸다. 인산염 탈착 등온선은 반응 시간이 짧은 경우 프로인드리히 등온선에, 반응 시간이 긴 경우 탬킨 등온선에 더 일치하는 경향을 보인다. 인산염 탈착 반응은 초기의 빠른 반응과, 후기의 느린 반응으로 구분된다. 흡착된 인산염의 농도가 높아질수록 탈착률은 감소하는 경향을 보이며, 탈착 시간이 길어지면 탈착률은 감소하는 경향을 보여준다.

• 한국연초학회지
• /
• 제3권1호
• /
• pp.30-40
• /
• 1981

The moisture sorption and desorption isotherms of various tobaccos were obtained over a relative humidity range from 0 to 90% at $20^{\circ}C$ and $30^{\circ}C$. The hysteresis effect, constant and rate of moisture sorption and desorption, monomolecular-layer moisture content, and specific surface area were analyzed from the obtained data. The moisture sorption and desorption isotherms showed a different characteristics for different tobacco varieties. At a lower humidity range below 50% RH, Burley tobacco had higher moisture sorption and desorption figures than Hicks and Basma, while, at a higher humidity range above 50% RH, Hicks had higher values than the others. The hysteresis effect of tobacco were greater in an intermediate humidity range (40-70% RN), and Basma showed a greater effect than the others. The sorption and desorption constant (K) increased with temperature, but decreased with RH, and Burley tobacco had larger K values, while Hicks had smaller K values than others. The sorption and desorption rate of Burley tobacco were greater than the other tobaccos. The monomolecular-layer moisture was 27.8 and 51.4mg/g, and the specific surface was 101 and $186m^2/g$, for Basma and Burley, respectively.

• 한국대기환경학회지
• /
• 제25권2호
• /
• pp.122-132
• /
• 2009

Adsorption of toluene by activated carbon fiber (ACF) coated with dielectric heating element and desorption by applying microwave were investigated. In order to prepare adsorbent so that VOC can be desorbed by microwave heating, fine dielectric heating element with nano size was coated on the surface of the ACF using hybrid binder. Eight adsorbents (ACF-DHE, Activated Carbon Fiber coated with Dielectric Heating Element) were prepared with different amount of dielectric heating element, kinds of hybrid binder, and solvent. In order to investigate adsorption characteristics, BET surface area, pore volume, and average pore size were measured for each adsorbent including ACF. Breakthrough experiments with toluene concentration, flow rate, bed length using fixed bed reactor were performed to investigate adsorbality of adsorbent, and results were compared with that of the ACF. Desorption reactor was constructed with modified microwave oven to investigate heating effect on ACF-DHE by applying microwave power. Each adsorbent saturated with toluene were put into desorption reactor. Composition of desorbed gas generated by applying controlled microwave power to reactor was measured. Up to now, hot air desorption method has been used. Experimental results showed that desorption method with new adsorbent prepared by coating dielectric heating element on ACF can be used for industrial application.

• Preventive Nutrition and Food Science
• /
• 제2권4호
• /
• pp.316-320
• /
• 1997

Phenolic acids are regarded as harmful materials in food and environment science but recently, as useful materials, and thus adsorption is recommended as an effective separation technique to recover or remove phenolic acids from diluted solution. If the adsorbed phenolic compounds were useful materials, the materials should be recovered through desorption. Desorption using supercritical carbon dioxide(SC-$CO_2$) was tried to separate food-borne phenolic acids from charcoal in single solute system. In the comparisons of desorption amounts, gallic acid had the lowest lolubiligy to SC-$CO_2$. Gallic acid has more hydroxy functional groups than the other phenolic acids, which was immiscible with nonpolar SC-$CO_2$. Ferulic acid was yielded more than p-coumaric acid, because ferulic acid had much bigger molecular weight, which was affected more by van der Waas force. It was found that the most affecting factor on desorption amounts was the solubility of phenolic acids to SC-$CO_2$. The second affecting factor was van der Waals force. Response surface methodology(RSM) was conducted to read the trend of desorption. Increasing density of SC-$CO_2$ raised solubility of phenolic acids.