• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.113-117
• /
• 2003

The digital systems include the noise in power supply, ground and packaging due to a simultaneous switching of signal, signal reflections and distortions on single and multiple transmission lines. The requirement for the controlled impedance on a PCB can be both a critical success factor and a design challenge. So, the invented tool simulates the tracks controlled impedance with the test coupon. It can saves the design time and supports the economical PCB design.

• Proceedings of the Korea Society of Design Studies Conference
• /
• 2000.11a
• /
• pp.130-131
• /
• 2000

근래 주거로 도입되는 첨단의 정보화 기술력은 공간적 제약과 모순을 보완해 주는 역할을 하고 있다. 이런 양상은 정보화시대에 알맞은 주거형태의 변화를 요구하게 되었고, 그에 대한 대안도 다양하게 제시되고 있다. 이처럼 미래의 주거는 정보화 기술에 의해 첨단화되고 많은 정보화 장비가 주호내부로 도입되어 기존의 주택에 존재하는 단점들을 보완해 주고 사람들로 하여금 편리한 생활을 영위할 수 있도록 해 줄 것이라 예측되고 있다.(중략)

• Proceeding of EDISON Challenge
• /
• 2017.03a
• /
• pp.290-303
• /
• 2017

This paper aims to build a drone platform based on an optimum design of its single arm. We assumed its single arm as a cantilevered beam with a tip mass. Based on the numerical optimization theory, we conducted validation and optimization of a new design by comparing the results with the similar ones obtained by ANSYS. Finally, this design is reflected in the control simulation, and the requirement of an optimum structural design considering the resonance situation is demonstrated.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1554-1556
• /
• 2009

In this paper, we propose a system to adjust specific color of image. The HSV of R/Y/G/C/B/M regions can be modified individually. The color reproduction can be preferred color, true color, or stander color for customer requirement.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.7 no.1
• /
• pp.13-23
• /
• 2004

There are several kinds of error factors in control system design. All error factors must be analysed before designing the control system. Therefore, each error factor must be compensated and eliminated completely. Systems Engineering can solve these error factors. In this paper, systems engineering approach on control system design are studied under model based systems engineering with RDD-100, Matlab-Simulink. Systems Engineering shall be used in defense development from control system design to system development.

• Science of Emotion and Sensibility
• /
• v.16 no.3
• /
• pp.397-408
• /
• 2013

According to increase of concerning in health and entry of aging society, sensor-based smart clothing has developed various type and applications. Sensor-based smart clothing should be designed with considering of the interaction between a human body-device-clothing, such as accuracy of signal, wearability, suitability and the configuration of the sensor and so on. In this respect, these characteristics distinguish sensor-based smart clothing process from clothing process and Sensor-based smart clothing process is expected to be needing requirements Specification for development purpose and interoperability assessment based on requirements engineering. In this study, to assess efficiency of process based on requirement engineering, the sensor-based smart clothing process was deducted in two types by analysis of empirical performance. Presented two process were empirically evaluated through qualitative and quantitative evaluation. As a result, design process II based on requiments engineering were confirmed more effective process than processI.

• Journal of the Korean Solar Energy Society
• /
• v.34 no.4
• /
• pp.17-22
• /
• 2014

The design of a fuel cells stack is important to get optimal output power. This study focuses on the evaluation of fuel cell system for unmaned aerial vehicles (UAVs). Low temperature proton exchange membrane (LTPEM) fuel cells are the most promising energy source for the robot applications because of their unique advantages such as high energy density, cold startup, and quick response during operation. In this paper, a 600 W open cathode LTPEM fuel cell was tested to evaluate the performance and to determine optimal operating conditions. The open cathode design reduces the overall size of the system to meet the requirement for robotic application. The cruise power requirement of 600 W was supported entirely by the fuel cell while the additional power requirements during takeoff was extended using a battery. A peak of power of 900 W is possible for 10 mins with a lithium polymer (LiPo) battery. The system was evaluated under various load cycles as well as start-stop cycles. The system response from no load to full load meets the robot platform requirement. The total weigh of the stack was 2 kg, while the overall system, including the fuel processing system and battery, was 4 kg.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.2
• /
• pp.149-154
• /
• 2012

While the Earthquake Resistant Design Part of Korean Roadway Bridge Design Code provides design procedures for the No Collapse Requirement, requirements for the Serviceability Limit State are not clearly provided. The basic design method to meet the No Collapse Requirement is the spectrum analysis method using response modification factors and the Serviceability Limit State is determined by both the importance factor and the response modification factor applied in the design procedure. The importance factor can be simply applied according to the bridge importance category, however, in moderate/low seismic regions the application of the response modification factor may bring different result according to design conditions. In this study, for a typical bridge in the moderate/low seismic regions, determination procedures for the Serviceability Limit State are reviewed by carrying out earthquake resistant design and supplementary provisions for the Earthquake Resistant Design Part are identified based on the study results.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.5
• /
• pp.79-87
• /
• 2021

This study suggests a design process for vibrotactile interface that can apply haptic perception factors reflecting human tactile mechanisms. This process consists of 4 stages: the haptic sense requirement analysis stage, the haptic element analysis stage, the haptic perception factor analysis stage, the haptic requirement detailed design, and the prototype implementation stage. The advantage of this design process is that unnecessary tasks can be excluded in deriving and implementing user requirements, by applying haptic perception factor analysis, and the biggest feature is that research results on ergonomic mechanisms can be reflected in the haptic design, completes prototype development simultaneously while determining the haptic requirements statement by performing user evaluation, usability testing, and haptic feature optimization tasks simultaneously. This design process includes all stages from user requirements to haptic function detailed design and prototype implementation, so it is expected that general developers who lack expertise in haptic will also be able to design user-centered designs, enabling design and implementation of haptic functions at a certain level.

• Journal of Bio-Environment Control
• /
• v.9 no.4
• /
• pp.201-206
• /
• 2000

A certain system to overcome high temperature should be introduced for the stable year-round cultivation in greenhouses. There are efficient methods to overcome high temperature such as ventilation system with shading screen, fan and pad system with screen, and fog system with screen. This study was carried out to find a means to determine the capacity of such system. Heat balance equations for each system were established and verified by experimental results. The calculated ventilation rates from heat balance equations showed a good agreement with the measured ones. The evapotranspiration coefficient was the most important parameter affecting the ventilation requirement among input parameter affecting the ventilation requirement among input parameters except weather data. When the evaportanspiration coefficient increased 1%, the ventilation requirement decreased 1.3%. Therefore the data of evapotranspiration coefficient should be accumulated by various experiments, and then design standards and selection guidelines should be provided. The simulation results for same design conditions shown that air exchanges requirement and evaporating water of fan and pad system were 5.1∼7.7% and 6.8∼9.3% larger than those of fog system, respectively.