• Journal of the Korean Society of Visualization
• /
• v.21 no.3
• /
• pp.23-32
• /
• 2023

This study aims to explore the heat transfer and flow phenomena inside an instant water heater and the influence of the design parameters of the water heater on the heating performance was investigated by 3-D numerical simulations considering heat convection. The design parameters are the heating ceramic dimension, the power of the heating device, and the water flow rate. The results show that a reasonable space for the heating device is required to optimize the heating performance. It is desirable to design higher heating device as possible for a given electric power. There exists a critical water flow rate that best meets the heating performance. The change in electric power has no impact on the flow phenomena and heating performance.

• Journal of Drive and Control
• /
• v.10 no.4
• /
• pp.29-33
• /
• 2013

Pneumatic system is widely applied in various industry because it have a many advantage(low cost, high safety, etc..). For design of pneumatic system, accurate flow measurement is required. In this study, compressible fluid flow measurement apparatus was designed and built. It uses an isothermal chamber that can approximate isothermal condition. Therefore, it can be measured for flow-rate using pressure response of isothermal chamber. As a result, this apparatus can be measured for sonic conductance and critical pressure ratio of pneumatic components and it required less time and energy than conventional flow meter. The effectiveness of the designed apparatus is proved by experimental result.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.670-675
• /
• 2001

This paper describes aerodynamic preliminary design performance prediction and flow analysis for turbine of the marine middle engine turbocharger. The performance characteristics of turbocharger turbine are investigated at various operating conditions using mass flow rate and computational flow analysis for rotor and nozzle at design point are performed. Preliminary design results are performed by applying mean line and radial equilibrium theory. Performance prediction and flow analysis results show good agreement with experiments. From 3 dimensional flow analysis result, efficiency is 0.6% greater than design point. Therefore, this design approach is useful for preliminary design, and helps to increase the design capability for optimized rotor blade.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.397-398
• /
• 2008

• Journal of the Korean Applied Science and Technology
• /
• v.27 no.2
• /
• pp.152-156
• /
• 2010

This study is focused on the channel design of bipolar plate in the electrode of hydrogen gas generator. The characteristics of hydrogen gas generation was studied in view of efficiency of hydrogen gas generation rate and a tendency of gas flow through the riv design of electrode. Since the flow rate of generated gas is the most crucial in determining the efficiency of hydrogen gas generator, we adopted the commercial analytical program of COMSOL $Multiphysics^{TM}$ to calculate the theoretical flow rate of hydrogen gas from the outlet of gas generator.

• Journal of the Korea Convergence Society
• /
• v.12 no.1
• /
• pp.171-176
• /
• 2021

The flow analysis by each configuration of automotive muffler in this study was carried out. And it aims at finding the design model that can increase the flow property best. It is shown that model B has the lowest maximum pressure and model C has the largest. Compared with the best flow rate according to the shape of the automotive muffler, model A had the comparatively smooth flow stream at the entrance and exit. However, model B has the largest flow rate in the muffler but the least flow rate in the exit, making it look less efficient. By the flow analysis result according to the muffler configuration, it is thought to design the muffler effectively by looking for the model with more smooth flow. The result of this study can be used to investigate the flow according to the configuration of small car muffler without actual test. It also seems to be helpful in the aesthetic convergent design of small car muffler.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.555-560
• /
• 2000

The modeling and the numerical analysis are done so as to develop the Computer Aided Design program for the design of flow control valve attached to the vane pump. The factors affecting the flow rate characteristics, are analyzed by the experiments and the numerical methods. It is shown that the main factor affecting to the first control flow is the diameter of small rod of the spool, the main factor affecting to the second control flow is the diameter of big rod of the spool, the main factors affecting to the cut off are the main spring constant, the initial displacement of main spring and small diameter of the spool, and the dropping slope characteristics of flow rate are decided by the chamfer of spool and the dynamic characteristics of the spool.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.2
• /
• pp.61-66
• /
• 2011

The purpose of this paper is to design a hydraulic actuator to operate under high pressure conditions. The flow characteristics under design conditions of hydraulic actuator were numerically conducted by commercial fluid dynamic code(ANSYS CFX V11). The numerical analysis was performed by transient technique according to the variation of stroke times, which was changed from 0 to 1 second by interval of 0.01. Turbulence model, $k-\omega$ SST was selected to secure more accurate prediction of hydraulic oil flow. The ICEM-CFD 11 and CFXMesher, reliable grid generation software was also adapted to secure high quality grid necessary for the reliable analysis. According to the simulation results, the flow rate which was supplied to the hydraulic actuator was 30.4l/min. These results are in good agreement with design results within 3.5% error.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.1
• /
• pp.25-33
• /
• 2016

This paper describes three-dimensional computational fluid dynamics (CFD) simulation of liquid-liquid flow and transient tracer tests in a full-scale continuous stirred-tank reactor (CSTR) used for drinking water treatment. To evaluate the effects of inlet flow rate on hydrodynamic behavior in the selected CSTR, inlet flow rate was changed from 10% to 100% of the design flow rate. From the results of CFD simulation and analysis, as the inlet flow rate increases, Modal index and ${\beta}$ value are increased. Also, Morrill index shows local minimal points in relation to the inlet flow rate, which are observed at 20% and 40% of the design flow. As inlet flow Increases more than 40%, it is shown that Morrill index re-increases to close to ideal CSTR.

• International Journal of Fluid Machinery and Systems
• /
• v.4 no.2
• /
• pp.262-270
• /
• 2011

Experimental and numerical investigations were conducted for an internal flow in an axial flow stator of a diagonal flow fan. A corner separation near the hub surface and the suction surface of a stator blade was focused on, and further, three-dimensional vortices in separated flow were investigated by the numerical analysis. At low flow rate of 80% of the design flow rate, a corner separation of the stator between the suction surface and the hub surface can be found in both experimental and calculated results. Separation vortices are observed in the limiting streamline patterns both on the blade suction and on the hub surfaces at 80% of the design flow rate in the calculated results. It also can be observed in the streamline pattern that both vortices from the blade suction surface and from the hub surface keep vortex structures up to far locations from these wall surfaces. An attempt to explain the vortices within a three-dimensional separation is introduced by using vortex filaments.