• Computers and Concrete
• /
• v.32 no.1
• /
• pp.99-117
• /
• 2023

The crack under the influence of the higher intensities of the stresses grows and the structure gets collapsed with the time when the crack length reaches to critical value. Therefore, the fracture behavior of a structure in terms of stress intensity factors (SIF) becomes important to determine the remaining fracture strength and capacity of material and structure for avoiding catastrophic failure, increasing safety and further improvement in the design. The robustness of the method has been demonstrated by comparing the numerical results with analytical and experimental results of some problems. XFEM is used to model cracks and holes in structures and predict their strength and reliability under service conditions. Further, XFEM is extended with a stochastic method for predicting the sensitivity in terms of output COVs and fracture strength in terms of mean values of stress intensity factors (SIFs) of a structure with discontinuities (cracks and holes) under tensile loading condition with input individual and combined randomness in different system parameters. In stochastic technique, the second order perturbation technique (SOPT) has been used for the predicting the fracture behavior of the structures. The stochastic/perturbation technique is also known as Taylor series expansion method and it provides the reliable results if the input randomness is less than twenty percentage. From the present numerical analysis it is observed that, the crack tip near to the hole is under the influence of the stress concentration and the variational effect of the input random parameters on the crack tip in terms of the SIFs are lesser so the COVs are the less sensitive. The COVs of mixed mode SIFs are the most sensitive for the crack angles (α=45° to 90°) for all the values of c₁ and d₁. The plate with the shorter distance between hole and crack is the most sensitive with all the crack angles but the crack tip which is much nearer to the hole has the highest sensitivity.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.4
• /
• pp.113-132
• /
• 1999

Recently in Korea, application of the soil nailing is gradually extended to the sites of excavations and slopes having various ground conditions and field characteristics. Design of the soil nailing is generally carried out in two steps, The First step is to examine the minimum safety factor against a sliding of the reinforced nailed-soil mass based on the limit equilibrium approach, and the second step is to check the maximum displacement expected to occur at facing using the numerical analysis technique. However, design parameters related to the soil nailing system are so various that a reliable design method considering interrelationships between these design parameters is continuously necessary. Additionally, taking into account the anisotropic characteristics of in-situ grounds, disturbances in collecting the soil samples and errors in measurements, a systematic analysis of the field measurement data as well as a rational technique of the optimum design is required to improve with respect to economical efficiency. As a part of these purposes, in the present study, a procedure for the optimum design of a soil nailing excavation wall system is proposed. Focusing on a minimization of the expenses in construction, the optimum design procedure is formulated based on the genetic algorithm. Neural network theory is further adopted in predicting the maximum horizontal displacement at a shotcrete facing. Using the proposed procedure, various effects of relevant design parameters are also analyzed. Finally, an optimized design section is compared with the existing design section at the excavation site being constructed, in order to verify a validity of the proposed procedure.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.22 no.4
• /
• pp.329-340
• /
• 2006

Statement of problem: Damping of the peak force transmitted to implants has been reported by in vitro studies using impact forces on resin-veneered superstructures. Theoretical assumptions suggest that use of acrylic resin for the occlusal surfaces of a prosthesis would protect the connection between implant and bone. Therefore, the relationship between prosthesis materials and the force transmitted through the implant system also needs to be investigated under conditions that resemble the intraoral mechanical environment. Purpose: The purpose of this study was to analyze the fracture strength and modes of temporary prosthesis when a flange or occlusally extended structure were connected on the top of the abutment. Material and method: Modified abutments of winged and bulk design were made by casting the desired wax pattern which is made on the UCLA type plastic cylinder. Temporary crowns were made using templates on the modified abutments, and its fracture toughness and strain were compared to the traditional temporary prosthesis. To evaluate the effect of aging, 5.000 times of thermocycling were performed, and their result was compared to the 24hours specimen result. Results: The following conclusions were drawn from this study: 1. In the fracture toughness test, temporary crown's fracture line located next to the screw hole while modified designs with metal support showed fracture line on the metal and its propagation along the metal-resin interface. 2. Wing and bulk structure didn't show significant difference in the fracture toughness (p>0.05), but wing structure showed stress concentration on the screw hole area compared to bulk structure which showed even stress distribution. 3. In the fracture toughness test after thermocycling, wing and bulk structure showed increased or similar results in metal supported area while off-metal area and temporary crown showed decreased results. 4. In the strain measurement after thermocycling, its value increased in the temporary and bulk structure. However, wing structure showed decreased value in the loading point while increased value in the screw hole area. Conclusion: Wing type design showed compatible result to the bulk type that its application with composite resin prosthesis to the implant dentistry is considered promising.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.29 no.12 s.148
• /
• pp.1619-1626
• /
• 2005

The durability of a stretch fabric is mainly related to the change in the dimension and mechanical properties of elastomeric fibers during wearing and washing. In this study, we examined the effects of washing temperature, presoaking time and the number of washing cycles on the change in length, tenacity, elongation at break, and permanent elongation after six repeated cycles of $100\%$ extension and relaxation of spandex yams with varying fineness and with a different rate of extension during heat-set. The spandex yarns continued to shrink as the wash temperature and the number of wash cycles increased. In addition, the finer spandex yams decreased in length more than the thicker yams. The increase in temperature and presoaking time tended to cause a slight decrease in the tenacity and elongation at break of the spandex yarns. Permanent elongation of the spandex yams also increased as the temperature, presoaking time and the number of washing cycles increased. Moreover, an extended presoaking time followed by washing at $40\%$ like repeated washing cycles showed the great increase in the permanent elongation of spandex yams. The thinner spandex yin had a better elasticity than the thicker one, since the former had a lower permanent elongation percentage than the latter. Based on the DSC thermograms, the melting points of the spandex yarns after washing were almost the same as those of the spandex yarns before washing.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.4
• /
• pp.19-42
• /
• 1999

In urban area, there are several major factors to be considered in tunnel design and construction. The first is to predict the magnitude and distribution of ground movements for particular ground conditions and construction procedures. The second is to assess the potential damage to nearby structures in response to the predicted ground movements. The third is to select the measures to be taken if a potential damage is foreseen. This study is concerned primarily with the first and second stages of the problem. Particularly, this paper is focused on the second stage to assess the potential damage to the nearby building with any type of geometries and locations above ground surface. In order to solve this problem, we introduced damage parameters(angular distortion, deflection ratio, maximum building settlements, maximum differential settlements, horizontal strain, etc.), and extended these parameters into 3-dimensional safety assessment. Also, to assess the safety of any walls existing in the building, we developed a 3-dimensional analysis program, and various parametric studies for the nearby building with any type of geometries and locations were presented. In addition to these parametric studies, we compared the results of the proposed techniques with some abroad case records for particular tunnels and adjacent buildings.

• Journal of The Korean Association For Science Education
• /
• v.37 no.1
• /
• pp.143-154
• /
• 2017

Science inquiry has long been emphasized in Korean science education. Scientific modeling is one of key practices in science inquiry with a potential to provide students with opportunities to develop their own explanations and knowledge thereafter. The purpose of this study is to investigate teacher's understanding of models in science and science teaching. A professional development program on Models (PDM) was developed and refined through three times of implementation while teachers' conceptions of models and modeling were examined. A total of 29 elementary and secondary teachers participated in this study. A survey based on model use of scientists in the history of science was developed and used to collect data and audio recordings of discussions among teachers and artifacts produced by the teachers during PDM were also collected. Three ways of ontological and two ways of epistemological understanding of models and modeling were found in teachers' ideas. After PDM, a quarter of the teachers changed their ontological understanding whereas very few changed their epistemological understanding. In contrast, more than two thirds of the teachers deepened and extended their ideas about using models and modeling in teaching. There were no clear relationships between teachers' understanding of models and ways and ideas about using models in science teaching. However, teachers' perceptions of school conditions were found to mediate their intention to use models in science teaching. The findings indicate possible approaches to professional development program content design and further research.

• The Journal of Industrial Distribution & Business
• /
• v.10 no.8
• /
• pp.45-53
• /
• 2019

Purpose - The purpose of this study was to clarify the factors to make an exclusive importation contract between foreign fashion brands and local retailers for successful business in Korea. Even though imported fashion brand market shows stead increasing in terms of sales amount, the number of store related study was very rare in fact. Meanwhile, as long as this business is glowing a lot of brands are suffering from bad business performance or getting in ruins thus these problems result in foreign currency loss. The local marketers therefore, strongly expect to know the solution for this matter. Research design, data, and methodology - For the qualitative research, 10 experts who are operating foreign brands with an exclusive contract at a department store or at duty free shop now and who had at least over 10 years of related working experience were included. The factors for the exclusive importation contract with foreign brands were drawn up through the one-to-one in-depth interview method from September 3, 2017 to January 15, 2018. The expert group for the validity analysis includes 2 professors and 5 postgraduate students. Results - As a result of qualitative study on the factors for imported fashion brand's launching with the exclusive importation contract, it turned out that there were 5 factors - safety, profitability, reliability, speed and global retailing. Safety, profitability, and reliability have been mentioned in most related surveys but some details are added and speed and global retailing have been newly highlighted and many unknown legal issues that it was not easy to get form common academic research are included. Speed simply means quick lead time and global retailing means stores where located in other countries. Conclusions - The reason that qualitative research should be done before the quantitative research is due to the scant theoretical background for this matter. Because the market of an imported fashion brand is steadily increasing, determining the factors to make exclusive importation contract is very meaningful from the point of academic and business. After this study, many marketers may get basic conditions to apply for real business and I hope the following quantitative research will give more effective results. The next study also will have extended range concerning industry area, product and distribution channel.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.14 no.2
• /
• pp.69-78
• /
• 1978

It is well known that the aluminizing steel is excellent in corrosion resistance and heat resistance. Therefore it has been used as boiler parts, heat exchanger parts and guide rails which are used under comparatively simple conditions. Recently, it has been noticed that aluminizing steel has high resistance to various atmosphere, high temperature oxidation and seawater resistance. So its usage has been extended widely to the production of parts such as intake and exhaust valve of internal combustion engine, turbine blade and pipelines On ships which required such properties. It is considered that aluminium coated steel is excellent in wear resistance because of high hardness on main ingredient FezAIs of Fe-AI alloy layer existed in diffusion coating layer. And it will beused as a new material taking wear resitance with seawater resistance in marine field. However it is difficult to findout any report concering the wear behaviors or properties of alum in izing steel. In this study the experiment was carried out under the condition of rolling-sliding contact using an Amsler-type wear testing machine at 0.80, 0.91, 1. 10, 1. 25% of slip ratio and 55.43, 78.38, 110.85 kg/mm^2 of Hertz's contact stress in run-in period for the purpose of service-ability test of aluminizing steel as a wear resisting material and obtaining the available design data. The followings are the obtained results from the experimen tal study; 1) The 2nd diffusion material has most excellent wear resistance. This material has brought out about 18% decrease of wear weight in a lower friction load level and 40~G decrease in a higher level comparing to the raw material. 2) Satisfactory effect of wear resistivity cannot be much expected in 2nd diffusion specimens. This is considered due to the formation of fine void in the alloy layer near the boundary to the aluminium layer. 3) Fracture on friction surface of aluminizing steel by the rolling-sliding contact is spalling, and spalling crack occurres initially beneath the specimen surface near the boundary in diffusion coating layer.

• Journal of Korea Water Resources Association
• /
• v.49 no.5
• /
• pp.439-450
• /
• 2016

For the design of infrastructures controlling the flood events at ungauged basins, this study tries to find the regional flood frequencies using peak flow data generated by the spatial extension of flood records. The Chungju Dam watershed is selected to validate the possibility of regional flood frequency analysis using the spatially extended flood data. Firstly, based on the index flood method, the flood event data from the spatial extension method is evaluated for 22 mid/smaller sub-basins at the Chungju Dam watershed. The homogeneity of the Chungju dam watershed was assessed in terms of the different size of watershed conditions such as accumulated and individual sub-basins. Based on the result of homogeneity analysis, this watershed is heterogeneous with respect to individual sub-basins because of the heterogeneity of rainfall distribution. To decide the regional probability distribution, goodness-of fit measure and weighted moving averages method from flood frequency analysis were adopted. Finally, GEV distribution was selected as a representative distribution and regional quantile were estimated. This research is one step further method to estimate regional flood frequency for ungauged basins.

• Journal of the Korea Institute of Building Construction
• /
• v.21 no.3
• /
• pp.213-219
• /
• 2021

Change orders that occur frequently during the construction phase, af ect the construction performance in terms of cost, time, quality, safety and environment, and place a huge burden for stakeholders of given projects. This study analyzed the causes of change orders and their impact on the basis of 721 cases and a questionnaire of 164 domestic U.S. military construction participants in a total of 24 U.S. military projects. Important factors for change orders in the US military construction projects were engineering change due to design errors (348 cases, 48.3%), user requests change(86 cases, 11.9%), and different site conditions (69 cases, 9.6%). In addition, due to the change orders, construction cost increased by 6.56% on average and construction period was extended by 21.1% compared to the original schedule. As a result, it is anticipated that domestic construction companies can obtain a better understanding of change orders and construction performance, which may be difficult due to accessibility and limitations to military facilities. Also, it is proposed a successor study that guides in the right direction for the U.S. Military Construction.