• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.404-409
• /
• 2007

For a hermetic reciprocating compressor, it has been known that the gas pulsation in the suction line affects the compressor performance, and suction muffler design has been focused on both of noise reduction and minimum pressure drop across the muffler. Some studies have been carried out on the mutual interaction between the gas pulsation and the cylinder pressure to investigate some supercharging effects, but their efforts were limited on rather simple geometries. In this paper, interaction of the gas pulsation in the compressor suction line with cylinder pressure via suction valve motion has been calculated; for the gas pulsation analysis, modeling of Helmholtz resonators in series was used, and for cylinder pressure calculation, energy equations was set up for the gas inside the cylinder. For demonstration of this calculation method, four different types of suction line configurations for a hermetic reciprocating compressor were compared in terms of compressor performance and gas pulsation level.

• Perspectives in Nursing Science
• /
• v.9 no.2
• /
• pp.136-145
• /
• 2012

Purpose: The purpose of this study was to verify the educational effectiveness of the Objective structured clinical examination (OSCE) module development activities on nursing students in the areas of performance skill, knowledge, self-directed learning readiness, and problem solving ability for medication skill. Methods: This study was a nonequivalent control group non-synchronized post-test design. The subjects (N=47), who agreed to participate in this study, were assigned to either the experimental (n=24) or control group (n=23). The experimental group was trained with OSCE module development activities for four days. The control group was trained with a traditional demonstration and practice class for the same amount of time as the experimental group. Medication performance skill and knowledge tests and surveys were done to measure self-directed learning readiness, and learning satisfaction after the experimental treatments. Results: The experimental group which participated in the OSCE module development activities showed significantly higher performance skill, self-directed learning readiness, and problem solving ability for skin test and insulin medication than that of the control group of traditional education. Conclusion: It is recommended to use the OSCE module development activities for nursing students in nursing education-learning in order to improve nursing skills.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.2
• /
• pp.76-80
• /
• 2012

This paper demonstrates how to implement inherent pitching stability in an insect-mimicking flapping-wing system for vertical takeoff. Design and fabrication of the insect-mimicking flapping-wing system is briefly described focusing on the recent modification. Force produced by the flapping-wing systems is estimated using the UBET (Unsteady Blade Element Theory) developed in the previous work. The estimation shows that the wing twist placed in the modified system can improve thrust production for about 10 %. The estimated thrust is compared with the measured thrust, which proves that the UBET provides fairly good estimations for the thrust produced by the flapping-wing systems. The vertical takeoff test shows that inherent pitching stability can be implemented in an insect-mimicking flapping-wing system by aligning the aerodynamic force center and center of gravity.

• Nuclear Engineering and Technology
• /
• v.37 no.6
• /
• pp.537-556
• /
• 2005

A primary-pipe rupture accident is one of the design-basis accidents of a High-Temperature Gas-cooled Reactor (HTGR). When the primary-pipe rupture accident occurs, air is expected to enter the reactor core from the breach and oxidize in-core graphite structures. This paper describes an experiment and analysis of the air ingress phenomena and the method fur the prevention of air ingress into the reactor during the primary-pipe rupture accident. The numerical results are in good agreement with the experimental ones regarding the density of the gas mixture, the concentration of each gas species produced by the graphite oxidation reaction and the onset time of the natural circulation of air. A hydrogen production system connected to the High-Temperature Engineering Test Reactor (HTTR) Is being designed to be able to produce hydrogen by themo-chemical iodine-Sulfur process, using a nuclear heat of 10 MW supplied by the HTTR. The HTTR hydrogen production system is first connected to a nuclear reactor in the world; hence a permeation test of hydrogen isotopes through heat exchanger is carried out to obtain detailed data for safety review and development of analytical codes. This paper also describes an overview of the hydrogen permeation test and permeability of hydrogen and deuterium of Hastelloy XR.

• YAKHAK HOEJI
• /
• v.44 no.4
• /
• pp.308-314
• /
• 2000

Logarithmic transformation of pharmacokinetic parameters is routinely used in bioequivalence studies based on pharmacokinetic and statistical grounds by the United States Food and Drug Administration (FDA), European Committee for Proprietary Medicinal Products (CPMP), and Japanese National Institute of Health and Science (NIHS). Although it has not yet been recommended by the Korea Food and Drug Administration (KFDA), its use is becoming increasingly necessary in order to harmonize with international standards. In the present study, statistical procedures for the analysis of a bioequivalence based on the log transformation and a related SAS procedure were demonstrated in order to aid the understanding and application. The AUC parameters used in this demonstration were taken from the previous bioequivalence study for two aceclofenac tablets, which were performed in a single-dose crossover design. Analysis of variance (ANOVA), statistical power to detect 20% difference between the tablets, minimum detectable difference and confidence intervals were all assessed following log-transformation of the data. Bioequivalence of two aceclofenac tablets was then estimated based on the guideline of FDA. Considering the international effort for harmaonization of guidelines for bioequivalence tests, this approach may require a further evaluation for a future adaptation in the Korea Guidelines of Bioequivalence Tests (KGBT).

• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.172-174
• /
• 1994

Due to the environmental considerations and the energy crisis, there has been a revival of electric vehicles since 1960s. Research and development work concerning with electric vehicles (EVs) was becoming more intense in last decade. As compared with conventional internal combustion engine (ICE) cars, EVs have the advantages of clean, quiet, better energy efficiency, less maintenance and improving the load factor of electric power systems. However, EVs usually have a snort running range, bad acceleration performance and high initial cost. The main reason for these shortcomings is the low figure of energy density and the high per energy cost of battery at present technology state. So it is very important to optimize the overall drive system design with respect to the maximum utilization of battery, energy, motor torque and inverter power. This paper describes a demonstration model of electric car which is driven by 4-wheel direct method using the vector control.

• Transactions of Materials Processing
• /
• v.13 no.6 s.70
• /
• pp.540-545
• /
• 2004

Ever since the ideal forming theory has been developed for process design purposes, application has been limited to sheet forming and, fur bulk forming, to two-dimensional steady flow. Here, application for the non-steady case was performed under the plane-strain condition based on the theory previously developed. In the ideal flow, material elements deform following the minimum plastic work path (or mostly proportional true strain path) so that the ideal plane-stram flow can be effectively described using the two-dimensional orthogonal convective coordinate system. Besides kinematics, fur a prescribed final part shape, schemes to optimize a preform shape out of a class of initial configurations and also to define the evolution of shapes and boundary tractions were developed. Discussions include the two problematic issues on internal tractions and the non-monotonous straining. For demonstration purposes, numerical calculations were made for a bulk part under forging.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.597-601
• /
• 2006

The advantages of solar energy are that it is renewable, infinite supplied and environmentally safe energy source. However, solar energy related products have the problems such as the limitation for installation, problems in maintenance and insufficient reliability which have been the barrier to consumers to satisfy the purchase need for solar heat related products. In this regard, in order to support the solar energy related companies the necessity for various technical information required for the commercialization of new products such as various performance test necessary for the certification of solar energy system, standardization for facilities and products, performance evaluation method and the measurement of performance is suggested. The purpose of this paper is to design the monitoring system for positive tests of system linked household hot water system using solar heat out of various solar energy systems, to establish an analysis and monitoring system for performance maintenance and operation technique, and to configure the centralized detection network by utilizing remote monitoring system. This research also aims at conducting monitoring for operation and performance evaluation in relation to database establishment and analytical evaluation and at describing the method of enhancing the reliability of solar energy system through the development of performance evaluation program.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.6 no.12
• /
• pp.3182-3196
• /
• 2012

In this paper, we present a new LED (Light Emitting Diode) mood lighting system interacting with smartphones based on the generation of different light sequences. In the proposed system, one light sequence is considered to be one unit of the service contents, which is then transmitted through a network and played in an LED lighting system. To this end, we propose a novel generation scheme using a smartphone, and a decoding/playing mechanism in an LED lighting system. The lighting sequences have a fixed period divided into predefined time units. Two modes - basic and interpolation - are supported in each time unit when playing a color sequence. In the basic mode, the color is maintained for the entire time unit, whereas in the interpolation mode the color is interpolated. The sequence is decoded and played in the lighting circuit by changing the duty cycle of a PWM (Pulse Width Modulation) signal. A demonstration system of the overall proposed method was using smartphones, a server and an LED lighting system. The results from this experiment show the validity and applicability of the proposed scheme.

• Journal of Distribution Science
• /
• v.19 no.12
• /
• pp.1-14
• /
• 2021

Purpose: For the last few decades, TQM has become a hot topic in the inner-disciplinary field in the production management line. Still, unfortunately, the study of TQM and Quality Output management is partially only attached to the tangible side in the production management line. Whereas theoretically, the implications of TQM require incremental improvement in all management lines (e.g., HRM, Marketing, Operations, and Distribution Management). Therefore, starting from the main problem, this study aims to analyze the effect of total quality management, Organizational Culture, Perceived Distribution of Quality Awareness, and quality output through a more in-depth analysis. Research design, data and methodology: We conducted a survey of 170 respondents from managers, staff, and employees from 48 companies in Indonesia. We used a quantitative approach with the SEM method to answer this study's problem formulation and hypotheses. Results: The results of our research stated that based on the demonstration of statistical test results, all hypotheses were positive and significant, both direct and indirect relationship demonstrations. Conclusions: Universally, the findings in this study illustrate that the supporting factor for creating value-added in TQM and Quality output lies in the optimal and positive organizational culture and Perceived Distribution Quality Awareness factors in the organization.