• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회논문집(I)
• /
• pp.253-258
• /
• 2000

Recently, the area of design optimization, especially structural optimization, has been and to be a continuous active area of research. And the design optimizations of port facilities have been achieved by many other civil engineers. But the design optimization of port facilities were limited to the design optimization of the breasting dolphin. This paper invested the design optimization of mooring pier and the foundations of mooring pier was suggested considering the convenience of repair and reinforcement work. The mooring pier devised with prestressed precast concrete panel and rigid frame welded wide flange beam to steel pipe pile. To accomplish the design optimization of mooring pier, the Augmented Lagrangian Multiplier Method(ALM) of ADS(Garret N. Vanderplaats) optimization routine, BFGS method as optimizer and Golden Section Method as one dimensional search were utilized. As a result, thirty percent of material cost for construction was reduced by design optimization. The tensile stress of concrete panel and bottom flage was critical constraints under service load. So, using high strength concrete and steel will be economical. And lots of initial values must be invested to accomplish the design optimization in design procedures.

• 한국자동차공학회논문집
• /
• 제22권1호
• /
• pp.142-147
• /
• 2014

Finite element analysis along with DOE scheme has been performed to obtain robust design of connecting rod assembly. An analysis was conducted with five loading steps. Fatigue analysis was done using commercial software FEMFAT and fatigue safety factors at the interested regions such as shank area of small end and big end were calculated. 27 design cases using 3 factors with 3 levels are constructed by design of experiment. Each case is simulated to find the most influential factors. Response for this study, maximum Von-Mises stress, has been used to determine main factors of connecting rod assembly. Among the 3 factors, compression load affected the response greatly. However, bolt assembly load and width of shank flat area showed a little influence to the response. Interaction effects among factors considered did not occur. Connecting rod assembly considered in this study showed its sensitivity to the noise factor such as compression load rather than design factor such as width of flat shank area.

• 한국디지털건축인테리어학회논문집
• /
• 제1권1호
• /
• pp.59-66
• /
• 2001

The purpose of this study is to improve productivity of architectural space planning(A.S.P,) by computer system and to optimize ASP. A searching algorithm is the best way to slave optimized A.S.P. Because architectural design is too many various site situations and client's demands to specify the general solving methods. This method seek the best design case in all possibility and to be modeled as this; Seongbukgu's case that is city structure former times negative by in facilities utilization of the near street limit. But, case of Gangnamgu and Songpagu is thought that environment and utilization etc. of area life of old people are affinity with quality of life environment of old people when see that is using various area facilities using electric railway and a bus etc. actively. It is looked by the other that individual's special quality uses area facilities according to life partner's existence and nonexistence and family composition and existence and nonexistence of profession and distinction of sex. Show difference of external behavior according to public garden and market and supermarket and welfare facilities etc.'s location in dwelling environment of area and relation about facilities of area has been formed and old people and dwelling environment of area can know that is that do interaction. Environment that access about facilities may have to be easy, and can live that communicating closely with area's inhabitantses may have to consist so that old people may can run various external life.. Notions of the evaluated value is an profit(+) and expense(-) that decide design intention. To adapt real planning, 1. A raster type space cell has logical site informations. 2. To be evaluate various factor. 3. To reflect operator's design mind, they should add an extra weight on evaluated value.

• 한국암반공학회:학술대회논문집
• /
• 한국암반공학회 2007년도 특별심포지엄 논문집
• /
• pp.63-79
• /
• 2007

Several remedial works were attempted to stabilize the collapsed area of the inlet slopes of diversion tunnel, but prevention of any further movement was being only carried out at beginning stage by filling the area with aggregates and rock debris, after several cracks had been initiated and developed around the area. The extra specialty developed folding zone is consisted with highly weathered Greywacke and Black shale. The suggested solution is to improve the properties of the rock mass of failed area by choosing the optimum level of reinforcement through the increment of slope rock support design so as to control the movement of slopes during the re-excavation. The Bakun hydroelectric project includes the construction of a hydroelectric power plant with an installed capacity of 2,520MW and a power transmission system connecting to the existing transmission networks in Sarawak and Western Malaysia. The power station will consist of a 210m height Concrete Faced Rockfill Dam. During the construction of the dam and the power facilities the Balui River has to be diverted of the tunnels is 12m and the tunnel width is 16m at the portal area. This paper describes the stability analysis and design methods for the open cut rock slopes in the inlet area of the diversion tunnels. The geotechnical parameters employed in stability calculations were given as a function of four defined Rock Mass Type (RMT) which were based on RMR system from Bieniawski. The stability calculations procedure of the rock slopes are divided into two stages. In the first stage, it is calculated for the stability of each "global" slope without any rock support and shotcrete system. In the second stage, it is calculated for each "local" slope stability with berms and supported with rock bolts and shotcrete. The monitoring instrumentation was performed continuously and some of the design modification was carried out in order to increase the safety of failed area based on the unforeseen geological risks during the open cut excavation.

• 한국조경학회지
• /
• 제30권5호
• /
• pp.89-97
• /
• 2002

This report describes the first prize design of Midongsan Eco-park, which is located in Chungcheongbuk-do (North Chungcheong) province. Criteria of the winning design are as follows: 1) The design should include a neighborhood park as well as a portion of a green zone, in order to harmonize the area ecosystem, gradually assimilate the surroundings, and serve as an education tool for the public. 2) According to an analysis of area maps and a site-inspection, a preserved area, a buffer area, a restored area, and a developed area should be developed. In the buffer and restored areas, major facilities and activity spaces should be set up. 3) Observation trails should be accessible to visitors, and a variety of adventure programs should be available. 4) The eco-park should be designed to provide a habitat for the Gorani (Chinese water deer) which used to live around Midongsan. 5) For sensuous and vivid visitor experiences, diverse programs are to be designed to accommodate different seasons, visitor ages, and required time. Environment and eco-education are to be emphasized to maximize the effect of the eco-programs. 6) Optimal activities for visitors of different ages, optimal time intervals and eco-programs by age are also suggested. 7) Facilities are zoned into three sections according to level of development. Each section has a main area and supplementary areas for better understanding. 8) Nature-friendly arrangement of facilities and construction should minimize earthwork and adverse effects on the local ecology. Throughout the planning, the following things were learned: longer-term analysis including all season's observation is essential; planning, designing, bui Iding and managing should be based on this careful, extended observation. The contest should have taken plate over a longer period of time in order enable more detailed planing of the eco-park For improved management and activities, a volunteer system in linked with schools eco-institutions and NGOs should be developed with eco-interpreters.

• 응용통계연구
• /
• 제24권6호
• /
• pp.1129-1138
• /
• 2011

지방자치제가 정착되면서 시군구와 같은 소지역 단위의 실업률에 대한 통계는 실업대책이나 고용지원 사업을 위한 예산 편성과 같은 지역 노동시장정책의 수립은 물론 정책 집행 후 그에 대한 사후평가를 하는데 있어서도 중요한 기준을 제공해주기 때문에 지자체 기관장들의 관심의 대상이 되고 있는 실정이다. 그러나 경제적, 시간적으로 많은 제약이 따르는 기초자치단체에서 지속적으로 실업률 통계를 생산하는 데에는 자료의 신뢰성, 연속성및 시의성 면에서 많은 문제를 노정하고 있다. 본 연구에서는 소지역 실업률 추정치에 대한 신뢰성(변동계수 25% 이하)을 확보하면서 통계생산에 소요되는 조사비용을 최소화할 수 있는 효율적인 추정법 및 최소 표본조사구 수를 모의실험을 통하여 제시하고자 한다.

• 한국정밀공학회지
• /
• 제17권4호
• /
• pp.97-105
• /
• 2000

One of the most important steps to determine the blank shape and dimensions in deep drawing process is to calculate the surface area of the product. In general, the surface area of axisymmetric products is calculated by mathematical or graphical methods. However, in the case of non-axisymmetric products, it is difficult to calculate the exact surface area due to errors as separated components. Fortunately, it is possible for elliptical products to recognize the geometry of the product in the long side and short side by drafting in another two layers on AutoCAD software. So, in this study, a surface area calculating system is constructed for a design of blank shape of deep drawing products. This system consists of input geometry recognition module and three dimensional modeling module, respectively. The suitability of this system is verified by applying to a real deep drawing product. The system constructed in this study would be very useful to reduce lead time and cost for determining the blank shape and dimensions.

• 교육녹색환경연구
• /
• 제6권1호
• /
• pp.49-59
• /
• 2007

The purpose of this study is to propose the type and size of space which is changed working plan as comparison with basic plan. It has been compared basic plan with working plan of 12 educational facilities which was designed basic plan by a professional research organization of educational facilities. The results of this study are summarized as follows; 1) The gross area of elementary school is decreased a course of working plan. But, the meddle and high school's gross area is increased. 2) It was downed 69.28 percent by the area of classroom at the primary school. At the meddle school, 3rd classroom's area increased by 22.65 percent, while 4th classroom's area down 33.98 percent. In case of high school, the area of 4th classroom and public lecture room increased by each 28.23 and 23.17 percent.

• 한국CDE학회논문집
• /
• 제4권4호
• /
• pp.355-359
• /
• 1999

This paper presents a method for determining machining parameters in electrical discharge machining process (EDM) based on discharge area. The parameters are the peak value of currents, the pulse-on time, and the pulse-off time, on which the EDM performance depends chiefly. The optimal machining parameters are closely related on discharge area, which can be calculated from a tool electrode and a discharge height. In the paper the discharge area is obtained from NC code for machining the tool electrode instead of its geometric model. The method consists of following three steps. First a Z-Map model is constructed from the NC code. Secondly, the discharge area is obtained from the Z-Map model and a Z-height. Finally, the machining parameters are calculated from the discharge area. An introduced example shows that the machining parameters are calculated by the using a Z-map model obtained from the machining data for a tool electrode.

• ETRI Journal
• /
• 제39권6호
• /
• pp.859-865
• /
• 2017

This paper presents a method for determining the optimum active-area width (OAW) of solar cells in a module architecture. The current density-voltage curve of a reference cell with a narrow active-area width is used to reproduce the current density profile in the test cell whose active area width is to be optimized. We obtained self-consistent current density and electric potential profiles from iterative calculations of both properties, considering the distributed resistance of the contact layers. Further, we determined the OAW that yields the maximum efficiency by calculating efficiency as a function of the active-area width. The proposed method can be applied to the design of the active area of a dye-sensitized solar cell in Z-type series connection modules for indoor and building-integrated photovoltaic systems. Our calculations predicted that OAW increases as the sheet resistances of the contact layers and the intensity of light decrease.