• Korean Journal of Environmental Agriculture
• /
• v.28 no.3
• /
• pp.258-265
• /
• 2009

To develop environmentally friendly constructed wetlands(CWs) for treating domestic sewage which was produced in farming and fishing village, the efficiency of water treatment at different ventilation systems in the vertical bed, depths of horizontal bed, and sewage loads was investigated. In the vertical bed, BOD and COD by duplex ventilation system were lower than those by single ventilation system. But T-N and T-P concentrations by both ventilation systems in the vertical bed were little different. In the horizontal bed, BOD, COD, T-N and T-P in 1.0 m and 1.3 m depths were little different. To reduce the CWs' area and to improve the pollutant removal efficiencies, the optimum depth of horizontal bed was 1.3 m. In single and duplex ventilation CWs, the removal rate of BOD, COD, SS, T-N and T-P decreased slightly with the sewage load increases. In same sewage load conditions, the removal rates of BOD, COD, SS, T-N and T-P by duplex ventilation CWs were higher than those by single ventilation CWs. In summary, to effectively treat domestic sewage from farming and fishing village, the optimum constructed wetlands would be the duplex ventilation CWs.

• Proceedings of the KACD Conference
• /
• 2008.05a
• /
• pp.177-183
• /
• 2008

It was reported that esthetic composite resin restoration reinforces the strength of remaining tooth structure with preserving the natural tooth structure. However, it is unknown how much the strength would be recovered. The purpose of this study was to compare the fracture resistance of three types of undermined cavity filled with composite resin with that of non-cavitated natural tooth. Forty sound upper molars were allocated randomly into four groups of 10 teeth. After flattening occlusal enamel. undermined cavities were prepared in thirty teeth to make three types of specimens with various thickness of occlusal structure (Group $1{\sim}3$). All the cavity have the 5 mm width mesio-distally and 7 mm depth bucco-lingually. Another natural 10 teeth (Group 4) were used as a control group. Teeth in group 1 have remaining occlusal structure about 1 mm thickness, which was composed of mainly enamel and small amount of dentin. In Group 2, remained thickness was about 1.5 mm, including 0.5 mm thickness dentin. In Group 3, thickness was about 2.0 mm, including 1 mm thickness dentin. Every effort was made to keep the remaining dentin thickness about 0.5 mm from the pulp space in cavitated groups. All the thickness was evaluated with radiographic Length Analyzer program. After acid etching with 37% phosphoric acid, one-bottle adhesive (Single $Bond^{TM}$, 3M/ESPE, USA) was applied following the manufacturer's recommendation and cavities were incrementally filled with hybrid composite resin (Filtek $Z-250^{TM}$, 3M/ESPE, USA). Teeth were stored in distilled water for one day at room temperature, after then, they were finished and polished with Sof-Lex system. All specimens were embedded in acrylic resin and static load was applied to the specimens with a 3 mm diameter stainless steel rod in an Universal testing machine and cross-head speed was 1 mm/min. Maximum load in case of fracture was recorded for each specimen. The data were statistically analyzed using one-way analysis of variance (ANOVA) and a Tukey test at the 95% confidence level. The results were as follows: 1. Fracture resistance of the undermined cavity filled with composite resin was about 75% of the natural tooth. 2. No significant difference on fracture loads of composite resin restoration was found among the three types of cavitated groups. Within the limits of this study, it can be concluded the fracture resistance of the undermined cavity filled with composite resin was lower than that of natural teeth, however remaining tooth structure may be supported and saved by the reinforcement with adhesive restoration, even of that portion consists of mainly enamel and a little dentin structure.

• Restorative Dentistry and Endodontics
• /
• v.33 no.3
• /
• pp.177-183
• /
• 2008

It was reported that esthetic composite resin restoration reinforces the strength of remaining tooth structure with preserving the natural tooth structure. However, it is unknown how much the strength would be recovered. The purpose of this study was to compare the fracture resistance of three types of undermined cavity filled with composite resin with that of non-cavitated natural tooth. Forty sound upper molars were allocated randomly into four groups of 10 teeth. After flattening occlusal enamel, undermined cavities were prepared in thirty teeth to make three types of specimens with various thickness of occlusal structure (Group $1{\sim}3$). All the cavity have the 5 mm width mesiodistally and 7 mm depth bucco-lingually. Another natural 10 teeth (Group 4) were used as a control group. Teeth in group 1 have remaining occlusal structure about 1 mm thickness, which was composed of mainly enamel and small amount of dentin. In Group 2, remained thickness was about 1.5 mm, including 0.5 mm thickness dentin. In Group 3, thickness was about 2.0 mm, including 1 mm thickness dentin. Every effort was made to keep the remaining dentin thickness about 0.5 mm from the pulp space in cavitated groups. All the thickness was evaluated with radiographic Length Analyzer program. After acid etching with 37% phosphoric acid, one-bottle adhesive (Single $Bond^{TM}$, 3M/ESPE, USA) was applied following the manufacturer's recommendation and cavities were incrementally filled with hybrid composite resin (Filtek $Z-250^{TM}$, 3M/ESPE, USA). Teeth were stored in distilled water for one day at room temperature, after then, they were finished and polished with Sof-Lex system. All specimens were embedded in acrylic resin and static load was applied to the specimens with a 3 mm diameter stainless steel rod in an Universal testing machine and cross-head speed was 1 mm/min. Maximum load in case of fracture was recorded for each specimen. The data were statistically analyzed using one-way analysis of variance (ANOVA) and a Tukey test at the 95% confidence level. The results were as follows: 1. Fracture resistance of the undermined cavity filled with composite resin was about 75% of the natural tooth. 2. No significant difference in fracture loads of composite resin restoration was found among the three types of cavitated groups. Within the limits of this study, it can be concluded the fracture resistance of the undermined cavity filled with composite resin was lower than that of natural teeth, however remaining tooth structure may be supported and saved by the reinforcement with adhesive restoration, even if that portion consists of mainly enamel and a little dentin structure.

• Korean Journal of Ecology and Environment
• /
• v.48 no.2
• /
• pp.108-114
• /
• 2015

Single - and combined effects of a domestic freshwater bivalve Unio douglasiae (7.6~8.6 cm in shell length) and zooplankton Daphnia magna (1~2 mm in body size) were examined to understand whether they inhibit the growth of harmful cyanobacterial bloom (i.e. Microcystis aeruginosa) in a eutrophic lake. The experiments were triplicated with twelve glass aquaria (40 L in volume); three aquaria without mussel and zooplankton, served as a control, three zooplankton aquaria (Z, density=40 indiv. $L^{-1}$), three mussel aquaria (M, density=0.5 indiv. $L^{-1}$), and three mussel plus zooplankton aquarium (ZM, density=40 indiv.Z $L^{-1}$ plus 0.5 indiv.M/L), respectively. Algal growth inhibition (%) calculated as a difference in the concentration of chlorophyll-a (Chl-a) before and after treatment. Chl-a in all aquaria decreased with the time, while a greatest algal inhibition was seen in the ZM aquaria. After 24 hrs of incubation, Chl-a concentration at the mid-depth (ca. 15 cm) in ZM aquaria reduced by 90.8% of the control, while 63.2% and 79.8% in Z and M aquaria, respectively. Interestingly, during the same period, the surface Chl-a was diminished by 51.9% and 65.4% relative to the control in Z and ZM aquaria, while 27.4% of initial concentration decreased in M aquarium, respectively. These results suggest that 1) this domestic freshwater filter-feeding bivalve plays a significant role in the control of cyanobacterial bloom (M. aeruginosa), and 2) the combination with zooplankton and mussel has a synergistic effect to diminish them, compared to the single treatment of zooplankton and mussel.

• Korean Journal of Remote Sensing
• /
• v.14 no.4
• /
• pp.353-365
• /
• 1998

Light absorption coefficient per unit mass of particles, i.e., specific absorption coefficient, is important as one of the main parameters in developing algorithms for ocean color remote sensing. Specific absorption coefficient of chlorophyll ($a^*_{ph}$) and suspended sediment ($a^*_{ss}$) were analyzed with a spectrophotometer using the "wet filter technique" and "Kishino method" for the seawater collected in the Yellow and Mediterranean Sea. An improved data-recovery method for the filter technique was also developed using spectrum slopes. This method recovered the baselines of spectrum that were often altered in the original methods. High $a^*_{ph}({lambda})$ values in the oligotrophic Mediterranean Sea and low values in the Yellow Sea were observed, ranging 0.01 to 0.12 $m^2$/mg at the chlorophyll maximum absorption wavelength of 440 nm. The empirical relationship between $a^*_{ph}$(440nm) and chlorophyll concentrations () was found to fit a power function ($a^*_{ph}$=0.039 $^{-0.369}$), which was similar to Bricaud et al. (1995). Absorption specific coefficients for suspended sediment ($a^*_{ss}$) did not show any relationship with concentrations of suspended sediment. However, an average value of $a^*_{ss}$ ranging 0.005 - 0.08 $m^2$/g at 440nm, was comparable to the specific absorption coefficient of soil (loess) measured by Ahn (1990). The morepronounced variability of $a^*_{ss}$ than $a^*_{ph}$ was determined from the variable mixing ratio values between particulate organic matter and mineral. It can also be explained by a wide size-distribution range for SS which were determined by their specific gravity, bottom state, depth and agitation of water mass by wind in the sea surface.

• Korean Journal of Soil Science and Fertilizer
• /
• v.22 no.4
• /
• pp.307-314
• /
• 1989

Barley, garlic, and soybean were cultivated in the silt loam, sandy loam, and loam, respectively, and the absorbing patterns of N, P, and K during growing of the crops were determined. While, the leaching of N, P, and K applied in the above soils in four levels of topsoil depths and in four leachate levels of excess precipitation was measured through the column. The depths of the soil were devised to 20, 35, 50, and 65cm, and the levels of excess water were classified to each leachate of 20, 40, 60, and 80mm precipitation, and nitrogen, phosphorous, and potassium in each fraction of the leachate were analyzed. By the analyses of the chemical components during growth of the crops, their absorbing patterns of N, P, and K were investigated. The order of N-leachings in the soils was sandy loam > loam > silt loam, and the leaching of $K_2O$ was very similar to N. The leaching of $P_2O_5$ was slight in all kinds of the soils. By the combination of the absorbing patterns of the crops in three kinds of soils and the leaching of the nitrogen in four levels of soil depth and four levels of excess precipitation, the method to replace the nitrogen lost by leaching was presented.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.24 no.1
• /
• pp.40-53
• /
• 2021

Research vessels(R/Vs) used for ocean research move to the planned research area and perform ocean observations suitable for the research purpose. The five research vessels of the Korea Institute of Ocean Science & Technology(KIOST) are equipped with global positioning system(GPS), water depth, weather, sea surface layer temperature and salinity measurement equipment that can be observed at all times during cruise. An information platform is required to systematically manage and utilize the data produced through such continuous observation equipment. Therefore, the data flow was defined through a series of business analysis ranging from the research vessel operation plan to observation during the operation of the research vessel, data collection, data processing, data storage, display and service. After creating a functional design for each stage of the business process, KIOST Underway Meteorological & Oceanographic Information System(KUMOS), a Web-Geographic information system (Web-GIS) based information platform, was built. Since the data produced during the cruise of the R/Vs have characteristics of temporal and spatial variability, a quality management system was developed that considered these variabilities. For the systematic management and service of data, the KUMOS integrated Database(DB) was established, and functions such as R/V tracking, data display, search and provision were implemented. The dataset provided by KUMOS consists of cruise report, raw data, Quality Control(QC) flagged data, filtered data, cruise track line data, and data report for each cruise of the R/V. The business processing procedure and system of KUMOS for each function developed through this study are expected to serve as a benchmark for domestic ocean-related institutions and universities that have research vessels capable of continuous observations during cruise.

• Korean Journal of Ichthyology
• /
• v.13 no.3
• /
• pp.181-189
• /
• 2001

Spawning behavior of the Takifugu pardarlis (Temminck et Schlegel) was observed on the Jook-do coast in Tongyong from March 1997 to June 1999. The spawning ground was locted in the intertidal zone between Tongyong and Koje-do. Its bottom was mainly gravels and stones, and its depth was 0.5~1.0 m. Spawning season was from the end of the March to the middle of May. During the spawning season, the mature fishes formed school a of 10~30 individuals, then moved to the spawning ground together. When a mature female spawned eggs, the attendant males fertilized them at the same time. The fertilized eggs obtained from the parent fishes caught at the spawning ground were adhesive, opaque and spherical, measuring 1.14~1.24 mm (mean 1.19 mm, n = 50) in diameter with numerous tiny oil globules. Hatching period was about 205 hours after fertilization at water temperature of $18.0{\pm}0.5^{\circ}C$. The newly hatched larvae were 2.92~3.10 mm (mean 3.01 mm, n = 20) in total length (TL), had a large yolk, and 11~13+14~15 = 25~28 myomeres. At 5 days, the larvae had attained 3.79~3.85 mm (mean 3.82 mm, n = 20) in TL and had transformed into the postlarval stage. At 15 days, the postlarvae had attained 7.78~7.90 mm (mean 7.84 mm, n = 20) in TL. At 21 days, had larvae attained 10.15~10.27 mm (mean 10.21 mm, n = 20) in TL and had reached the juvenile stage. All fins were formed with a complete set of fin rays having the following counts: dorsal fin rays 11~12; anal fin rays 9; pectoral fin rays 14~15; caudal fin rays 11~12.

• Korean Journal of Soil Science and Fertilizer
• /
• v.34 no.4
• /
• pp.292-301
• /
• 2001

The objectives of this study were to measure the changes in soil moisture regimes and the distribution patterns of inorganic N derived from the fertigated $^{15}N$-labeled urea, and compare them with the results obtained from broadcast-applied soil under the same drip irrigation domain. In fertigated soil, a $^{15}N$-labeled urea solution of $117mg\;N\;L^{-1}$ was applied by surface drip irrigation for 4 weeks. In broadcast-applied soil, no the other hand, 4 g of $^{15}N$-labeled urea(1.87 g N) mixed thoroughly with 5 kg of soil was placed on the surface of packed soil. Soil water status was controlled by drip irrigation scheduled at soil matric potential of -50 kPa. A calibrated time-domain reflectometry probe was installed in the soil vertically 15 cm apart from a drip emitter to control drip irrigation. About 60% of urea-derived inorganic nitrogen was remained in the top zone between 0 and 10 cm depth of fertigated soil, while, most of the inorganic nitrogen (91%) was accumulated in the top zone of broadcast-applied soil. Of inorganic nitrogen derived from urea, the percentage of $NO_3{^-}$ was much higher for fertigation (99%) than for surface application (62%). The relatively lower recovery of urea-derived inorganic nitrogen of broadcast-applied urea-N (51%) than that of fertigated urea-N (89%) was attributable to enhanced $NH_3$ volatilization.

• Journal of Wetlands Research
• /
• v.7 no.2
• /
• pp.69-88
• /
• 2005

Distribution of benthic macrofauna was surveyed in the subtidal area and on the sand flat of Sindu-ri coast during July 2002. A total of 134 species, 3,511 individuals and 388g biomass of macrobenthos were sampled inclusively from the study sites. 109 species with a mean density of $1,298ind./m^2$ and biomass of $69.4g/m^2$ were collected from 10 stations established in the subtidal area. Polychaetes were represented as a dominant faunal group of the subtidal area in both species richness and density with values of 54 species and $813ind./m^2$. Cluster analysis based on the faunal composition showed that the subtidal area could be divided into four stational groups according to sedimentary characteristics: Cirrophorus armatus - Lumbrineris longifolia association on the mud sediment with pebbles near aqua-farms; Aonides oxycephala association on the rocky bed; Scoloplos armiger - Grandifoxus cuspis association on the sand-dominated sediment along the lowest low water; a association with higher evenness on the sand-dominated sediment in the depth. Although having characteristics of high value in species richness, density and species diversity, the macrobenthic association around the farming area was dominated by the opportunistic species such as Lumbrineris longifolia and Tharyx sp. Natural community represented by S. armiger and G. cuspis was developed in most sand-dominated areas. 50 species were sampled with a mean density of $2,443ind./m^2$ and biomass of $381.3g/m^2$ from eight+ stations along two transects on Sindu-ri sand flat. Mollusks were represented as a dominant faunal group of the sand flat in species richness, density and biomass with values of 20 species, $1,345ind./m^2$ and $350.4g/m^2$, respectively. Umbonium thomasi, Veneridae sp., Mandibulophoxus mai, Armandia lanceolata, Eohaustorius spinigerus, Urothoe convexa were dominant species and these species accounted for over 83% of total individuals. There were three distinct zones of macrobenthos on Sindu-ri sand flat according to the extent of exposure time. The upper zone was dominated by Scopimera globosa, the middle zone was characterized by M. mai, and the lower zone was dominated by E. spinigerus. Sindu-ri coastal area was considered as a healthy habitat for macrobenthos, except for around the farming area. It was considered that Sindu-ri coastal area including the sand flat connected to the sand dune of natural monument was a valuable habitat as a protected site in having no pollution source and no artificial structure.