• Economic and Environmental Geology
• /
• v.44 no.6
• /
• pp.513-523
• /
• 2011

We estimated geothermal power generation potential in Korea through Enhanced Geothermal System (EGS) technology following the recently proposed protocol which was endorsed by international organizations. Input thermal and physical data for estimation are density, specific heat and thermal conductivity measurements from 1,516 outcrop samples, 180 heat production, 352 heat flow, and 52 mean surface temperature data. Inland area was digitized into 34,742 grids of $1'{\times}1'$ size and temperature distribution and available heat were calculated for 1 km depth interval from 3 km down to 10 km. Thus estimated theoretical potential reached 6,975 GW which is 92 times total generation capacity of Korea in 2010. Technical potential down to 6.5 km and considering land accessibility, thermal recovery ratio of 0.14 and temperature drawdown factor of $10^{\circ}C$ was 19.6 GW. If we disregard temperature drawdown factor, which can be considered in estimating economic potential, the technical potential increases up to 56 GW.

• Economic and Environmental Geology
• /
• v.47 no.6
• /
• pp.625-633
• /
• 2014

The Aquistore project is the world's first commercial capture, transportation, utilization and storage project of post-combustion $CO_2$ from a coal-fired thermo electric power plant, and the proposed storage is a saline aquifer at a depth of about 3,500 m. Deep saline aquifer, compared to hydrocarbon reservoir, provides the great volumetric potential for storage of $CO_2$ anywhere in the world, therefore the research results from the project may be exported globally to other sites. Geological $CO_2$ storage characterization for saline aquifer instead of hydrocarbon reservoir needs to estimate the geophysical properties of subsurface geology. This study calculated the geophysical property of water-saturated formation by applying amplitude variation analysis developed from oil and gas exploration. We correlated horizon tops at the well logs to seismic traveltime of 1,815 and 1,857 ms as Winnipeg and Deadwood formations. Gradient analysis from seismic traces showed correlation coefficient of 45 - 81 % on amplitude variation with respect to incident angle. Crossplot of intercept and gradient shows the inverse proportional trend which represents typical water saturated sediments. Product attribute of intercept and gradient described the base of wet sediment. Poisson's ratio change attribute increased at the top of target area satisfying with wet sediment and decreased at the top of basement in a dry rock bed.

• Journal of Biomedical Engineering Research
• /
• v.35 no.5
• /
• pp.160-168
• /
• 2014

Continuous body temperature monitoring is useful and essential in diverse medical procedures such as infection onset detection, therapeutic hypothermia, circadian rhythm monitoring, sleep disorder assessment, and gynecological research. However, the existing thermometers are too invasive or intrusive to be applied to long-term body temperature monitoring. In our previous study, we invented the bi-medium deep body thermometer which can noninvasively and continuously monitor deep tissue temperature. And the ratio of thermal resistances expressed as K-value should be obtained to estimate body temperature with the thermometer and it can be different under various measurement environments. Although the device was proven to be useful through preliminary simulation test and small group of human study, the experimental environment was restrictive in our previous approach. In this study, a finite element simulation was executed to obtain the K-value and evaluate the accuracy of bi-medium thermometer under various measurement environments. In addition, K-value estimation equation was developed by analyzing the influence of 5 measurement environmental factors (medium length, medium height, tissue depth, blood perfusion rate, and ambient temperature) on K-value. The results revealed that the estimation accuracy of bi-medium deep body thermometer based on computer simulation was very high (RMSE < $0.003^{\circ}C$) in various measurement environments. Also, bi-medium deep body thermometer based on K-value estimation equation showed relatively accurate results (RMSE < $0.3^{\circ}C$) except for one case. Although the K-value estimation technology should be improved for more accurate body temperature estimation, the results of finite element simulation showed that bi-medium deep body thermometer could accurately measure various tissue temperatures under diverse environments.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.2
• /
• pp.102-109
• /
• 2016

This paper presents mechanical properties and chloride diffusivity of the recycled aggregate concretes(RAC) in which natural coarse aggregate was replaced by recycled coarse aggregate(RCA) by compressive strength levels(20, 35, 50 MPa). A total of 9 RAC were produced and classified into three series, each of which included three mixes designed with three compressive strength levels of 20 MPa, 35 MPa and 50 MPa and three RCA replacement ratios of 0, 50 and 100%. Engineering properties of RAC were tested for slump test, air content, compressive strength, chloride penetration depth and chloride diffusion coefficient. The test results indicated that the workability of RAC could be improved or same by RCA replacement ratios, when compared with that containing no RCA. This is probably because of the RCA shape improving the workability of RAC. Also, the test results showed that the compressive strength was decreased by 9~10% as the RCA replacement ratios increase. Furthermore, the result indicated that the measured chloride diffusion coefficient increases by 144% with the increase of the RCA replacement. In the case of the concrete having low level compressive strength, the increase of chloride diffusion coefficient tends to be higher when using the RCA. However, the trend of chloride diffusion coefficient in high level compressive strength concrete is similar to that obtained in general concrete. This is because that the effect of the RCA replacement could be a decrease with increase of compressive strength. Therefore, an advance on the admixture application and mix ratio control are required to improve the chloride resistivity when using the recycled aggregate in large scale.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.5
• /
• pp.83-91
• /
• 2015

With varying conditions of concrete surface, induced chloride contents are changed and this is a key parameter for steel corrosion and service life in RC (Reinforced Concrete) structures. Many surface enhancement techniques using impregnation have been developed, however the evaluation techniques for chloride behavior through doubly layered media and time-dependent diffusion are rarely proposed. This paper presents an analysis technique considering double-layer concrete and time-dependent diffusion behavior, and the results are compared with those from the previous test results through reverse analysis. The chloride profiles from the surface-impregnated concrete exposed to atmospheric, tidal, submerged zone for 2 years are adopted. Furthermore surface chloride contents and diffusion coefficients are obtained, and are compared with those from Life365. Through consideration of time effect, the relative error decreases from 0.28 to 0.20 in atmospheric, 0.29 to 0.11 in tidal, and 0.54 to 0.40 in submerged zone, respectively, which shows more reasonable results. Utilizing the diffusion coefficients from Life365, relative errors increases and it needs deeper penetration depth (e) and lower diffusion coefficient ratio ($D_1/D_2$) due to higher diffusion coefficient.

• Korean Journal of Optics and Photonics
• /
• v.11 no.2
• /
• pp.73-79
• /
• 2000

We measure a beam diameter of scan and sub-scan direction of LSD (Laser Scanning Urnt) which uses $fheta$ lens produced by injecLion molding method as a scanning lens. While the measured beam diameter in scan direction, which is $62muextrm{m}$ to $68\mu\textrm{m}$, shows similar size comparing to the design beam diameter, the sub-scan beam diameter shows sIzable beam diameter deviation as much as 37 11m ranging from $78\mu\textrm{m}$ to $115\mu\textrm{m}$. Injection molding lens has the surface figure error due to the shrinkage III the cooling time and the internal distortion (birefringence) due to the uneven cooling conditIOn so that these bring about wavefront aberration (i.e., the enlargement of beam size), and are eventually expre~sed as the deterioration of the pdnting image. In this paper. we first measure and analyze beam diameter, birefringence (polanzation ratio), and asphedcal figure error of mIens in order to know the principle cause of the beam diameter deviation in sub-scan directIOn. And Lhen. through the analysis of a designed depth of focus and a calculated field curvature (imaging position of the optical axis directIon) using the above figure elTor data, we know Lhat the birefringence IS the main factor of sizable beam diameter deVIation in sub-scan direction. ction.

• Radiation Oncology Journal
• /
• v.19 no.3
• /
• pp.293-299
• /
• 2001

Prupose : LiF TLD has a problem to be used in vivo dosimetry because of the toxic property of LiF. The aim of this study is to develop new dosimeter with LiF TLD to be used in vivo dosimetry. Materials and methods : We designed and manufactured the teflon box(here after TLD holder) to put TLD in. The external size of TLD holder is $4\times4\times1\;mm^3$ To estimate the effect of TLD holder on TLD response for radiation, the linearity of TLD response to nominal dose were measured for TLD in TLD holder. Measurement were peformed in the 10 MV x-ray beam with LiF TLD using a solid water phantom at SSD of 100 cm. Percent Depth Dose (PDD) and Tissue-Maximum Ratio (TMR) with varying phantom thickness on TLD were measured to find the effect of TLD holder on the dose coefficient used for dose calculation in radiation therapy. Results : The linearity of response of TLD in TLD holder to the nominal dose was improved than TLD only used as dosimeter And in various measurement conditions, it makes a marginnal difference between TLD in TLD holder and TLD only in their responses. Conclusion : It was proven that the TLD in TLD holder as a new dosimetry could be used in vivo dosimetry.

• Korean Journal of Ichthyology
• /
• v.33 no.3
• /
• pp.177-183
• /
• 2021

Distribution aspects and extinction threat evaluation of the endangered species, Rhynchocypris semotilus were investigated in Goseong-gun, Gangwon-do, Korea, June 2020. Among the 12 sampling sites investigated during the study period, samples of R. semotilus were collected 268 individuals at 6 sites. The streams inhabited of R. semotilus were Songhyeoncheon (3 stations), Gojindong (2 stations) and Osodong (1 station). The main habitats of R. semotilus were uppermost and upper stream (Aa type) with 3~15 m water flow width, 0.3~1.3 m depth and high ratio boulder and cobble bottoms. The estimated age of the R. semotilus (June) based on their total length distribution indicated that 0-, 1-, 2-, 3- and more than 4-year-old were 6~27 mm, 38~59 mm, 60~75 mm, 78~93 mm and 96~125 mm, respectively, and their has matured reproductive organs over two years old. R. semotilus investigation results of the threat of extinction showed no tendency to decrease in population size, but estimated to be less than 1,000 mature individuals, with a small range of extend of occurrence (39.668 km²), area of occupancy (16 km²), and number of disconnected locations (3 locations). Therefore, R. semotilus is now considered vulnerable (VU D2) based on the IUCN Red List categories and criteria.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.4
• /
• pp.324-330
• /
• 2018

In accordance with the amendment of the Industrial Safety and Health Act of 2007, Korea completely prohibited the import, distribution and manufacture of asbestos like Europe and Japan. Accordingly, the current problem of asbestos is the safe maintenance and disposal of asbestos construction material, the disposal of asbestos, and the final disposal of asbestos building materials. In the past, Korea used 100,000 tons of asbestos every year, and the building materials using it exceeded 1 million tons per year. These asbestos building materials continued to be used until 2006, and the Ministry predicted that these materials would continue to be maintained until 2044. When the permeable hardening agent is applied to the asbestos building material installed in the pre-pretreatment step for the harmless treatment of the asbestos waste and the dismantling is carried out, the scattering of the asbestos is suppressed in the disassembling step, detoxification treatment conditions can be improved. Therefore, permeable hardeners should be stably penetrated into asbestos building materials. In this study, it is suggested that pre - pretreatment methods for the harmlessization of waste asbestos building materials with medium density level can be presented. In order to efficiently perform pre - treatment for chemical harmlessness in the future, the mixing ratio of permeable hardener and middle water Optimization is the most important factor.

• The Journal of the Korea Contents Association
• /
• v.19 no.4
• /
• pp.218-226
• /
• 2019

As the shoes industry has been strengthened due to the contemporary fashion industry becoming segmented more and more, it is necessary to provide the basic data for the shoes industry through more in-depth research on the relevant fields. Accordingly, this study investigated the research trends related to shoes in Korea on the aspect of the publication methods, research contents and research methodologies for identifying the existing research status. In accordance with the analysis, the researches had been published since 2015 and presented by one author or two co-authors. The authors of researches were mostly affiliated to the colleges. Thus, it was identified that the professional research should be implemented in cooperation with the industry. For the research contents, the researches related to the shoes industry focused on the 21st century in the period field and marketing and design in the theme field. Then, it is required to investigate the converged interdisciplinary themes in wider areas in more diverse periods. Next, the case study accounted for the highest ratio in the methodology. Moreover, the methodology applied per theme showed the significant difference. Accordingly, the researches need to be conducted through more diverse viewpoints and methodologies. In case of the difference per research type, the significant difference was found only in the research approaches. Furthermore, the specific methodology was preferred per theme regardless of the research types. Then, it was found that the methodology played the significant role in the researches on the shoes industry.