• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권2호
• /
• pp.83-88
• /
• 2006

AC loss is one of the main research area in AC power application using high temperature superconductor(HTS), such as HTS transformer, HTS current limiter and HTS cable, because it is closely related to efficiency, economic estimation and design of power device. A lot of research for various arrangements of HTS tapes have been performed to increase a capacity of transport current because single HTS tape can not satisfy the demanded current capacity in HTS power application. In this paper, we studied magnetization loss by different several arrangements of BSCCO tapes such as Edge-to-Edge type, Face-to-Face type and Matrix type through numerical analysis by 2D-FEM and measurement. As a result, we got the result that the magnetization loss of Face-to-Face type arrangements was lower than those of other arrangement types under the conditions of the same stacking number. We think that the result was due to shield effect by demagnetization of adjacent HTS tapes which are located face to face.

• Advances in materials Research
• /
• 제4권4호
• /
• pp.227-233
• /
• 2015

We present a method, supported by theoretical analysis, for optimizing the usage of the critical rare earth element dysprosium in $Nd_2Fe_{14}B$ (NdFeB)-based permanent magnets. In this method, we use Dy selectively in locations such as magnet edges and faces, where demagnetization factors are largest, rather than uniformly throughout the bulk sample. A200 nm thick Dy film was sputtered onto a commercial N-38, NdFeB magnets with a thickness of 3 mm and post-annealed at temperatures from $600-700^{\circ}C$. Magnets displayed enhanced coercivities after post-annealing and as much as a 5 % increase in the energy product, while requiring a total Dy content of 0.06 wt. % - a small fraction of that used in the commercial grade Dy-NdFeB magnets. By assuming all Dy diffused into NdFeB magnets, the improvement in energy product corresponds to a saving of over 1% Dy (critical element). Magnets manufactured using this technique will therefore be higher performing which would potentially broaden the application space of these magnets in the traction motors of hybrid and pure electric vehicles, and wind generators.

• 한국태양에너지학회 논문집
• /
• 제23권3호
• /
• pp.29-35
• /
• 2003

Generator for wind power can be either synchronous or asynchronous (induction) types. Induction and synchronous generators behave in a different way when subjected to severe faults. Induction generators does not have an angle stability limit and short circuit in the neighborhood of an Induction generator causes the demagnetization of the machine when the fault is cleared, the voltage raises slowly, while the grid contributes with reactive power to the generator and the magnetic flux recovers. On the other hand in the synchronous generators the recovery of the voltage is immediate, since the excitation of the rotor angle comes from an independent circuit. This paper shows the result of the transient state analysis in the network connected to wind generation system Several case studies have been conducted to determine the effect of the clearing time of a fault on the network stability. It has been found that the critical clearing time can be as low as 61ms in the case of induction generator compared to 370ms in the case of synchronous generator.

• Journal of Electrical Engineering and Technology
• /
• 제13권5호
• /
• pp.1956-1964
• /
• 2018

Since the stator winding of High-Speed Permanent Magnet Generator (HSPMG) has few winding turns and low inductance value, it is more prone to be influenced by harmonic current. Moreover, the operation efficiency and the torque stability of HSPMG will be greatly influenced by harmonic current. Taking a 117 kW, 60 000 rpm HSPMG as an example, in order to analyze the effects of harmonic current on HSPMG in this paper, the 2-D finite element electromagnetic field model of the generator was established and the correctness of the model was verified by testing the generator prototype. Based on the model, the losses and torque of the generator under different frequency harmonic current were studied. The change rules of the losses and torque were found out. Based on the analysis of the influence of the harmonic phase angle on torque ripple, it is found that the torque ripple could be weakened through changing the harmonic phase angle. Through the analysis of eddy current density in rotor, the change mechanism of the rotor eddy current loss was revealed. These conclusions can contribute to reduce harmonic loss, prevent demagnetization fault and optimize torque ripple of HSPMG used in distributed power supply system.

• 전기학회논문지
• /
• 제66권1호
• /
• pp.27-32
• /
• 2017

In this paper, slot less type high-speed and compact motor was designed. it was selected through change of stator coil distribution for the optimal performance of the motor. In this paper, designed motor was expected to be very vulnerable to heat dissipation in a compact motor. Therefore, to ensure reliability in the design result, winding and permanent magnet damage caused by the losses of motor was analyzed by thermal analysis and demagnetization analysis. Using the result, whether motor burnout was confirmed by motor performance degradation and insulation breakdown.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.2310-2316
• /
• 2011

In order to apply Interior Permanet Magnet Synchronous Motor(IPMSM) to the propulsion system of the railway transit, 110 (kW) class IPMSMs with high-power density are designed as a concentrated winding model and a distributed winding model in this study. The concentrated winding model designed in this study is 6 poles/9 slots and the distributed winding model is 6 poles/36 slots. In general, the eddy current losses in the permanent magnets of IPMSM are caused by the slot harmonics. The thermal demagnetization of the magnet by the eddy current losses at high rotational speed often becomes one of the major problems in the IPMSM with a concentrated windings especially. A design to reduce eddy current losses in permanent magnets design is important in IPMSM for the railway vehicle propulsion system which requires high-speed operation. Therefore, a method to devide the permanent magnet is proposed to reduce the eddy current losses in permanent magnet in this study. Authors analyze the variation characteristics of the eddy current losses generated in permanent magnet of the concentrated winding model by changing the number of the division of the permanent magnets.

• Journal of Astronomy and Space Sciences
• /
• 제22권1호
• /
• pp.35-46
• /
• 2005

This paper addresses the design and analysis results of a 2-axes magnetometer for attitude determination of small satellite. A low-cost and efficient 2-axes fluxgate magnetometer was selected as the most suitable attitude sensor for LEO microsatellites which require a low-to-medium level pointing accuracy. An optimization trade-off study has been performed for the development of 2-axes fluxgate magnetometer. All the relevant parameters such as permeability, demagnetization factor, coil diameter, core thickness, and number of coil turns were considered for the sizing of a small satellite magnetometer. The magnetometer which is designed, manufactured, and tested in-house as described in this paper satisfies linearity requirement for determining attitude position of small satellites. On the basis of magnetometer which is designed in Space System Research Lab. (SSRL), commercial magnetometer will be developed.

• Journal of Magnetics
• /
• 제7권2호
• /
• pp.45-50
• /
• 2002

A magnetic field annealing is firstly used for nanostructured Sm-Co/Co films, prepared by magnetron sputtering method. The effects of magnetic field annealing on single-layered Sm-Co films are different from those on multi-layered Sm-Co/Co films. A detailed analysis of microstructures and magnetic properties is made by means of HRTEM, Auger electron spectroscopy, XRD and Physical Property Measurement System (PPMS). From magnetic properties and microstructure analysis, it was confirmed that these differences originate from the effects of magnetic field annealing on crystallization behavior of the films. The relationship between magnetic properties and microstructures explains a different demagnetization process of single-layered and multilayered films. For the single-layered Sm-Co films, magnetic-field-annealing makes the main phases change from $CaCu_5/ to Zn_2Th_{17}$ structure, resulting in a decrease of coercivity. The results show that the magnetic-field-annealing is useful to improve the properties of nanostructured Sm-Co(30 nm)/Co(10 nm) films, which ascribe to improving the pinning effectiveness in coercivity mechanism and decreasing the magnetostatic interaction of films. A very high coercivity about 0.7 T was obtained from nanoscaled multi-layered Sm-Co(30 nm)-/Co(10 nm) films.

• 자원환경지질
• /
• 제31권4호
• /
• pp.311-324
• /
• 1998

Paleomagnetic study is carried out to investigate the possibility of remagnetization by dikes in the Cretaceous Gyeongsang Basin. We selected a site for a contact test as a preliminary study, and collected 41 core samples (7 from andesitic dike, 17 from sedimentary rock on the left side of dike and 17 from sedimentary rock on the right side). Magnetite was responsible for the remagnetization based on microscopic observation and demagnetization analysis. Although the increasement of magnetic susceptibility appears on both sides about 100 cm from the dike, the increment of NRM intensity was obtained from the specimens on the left side only. This is interpreted that the size of magnetite newly formed is dominated by superparamagnetic grains in the right side, but by larger than single-domain grains in the left. Reversed polarity component remagnetized by intrusion of dike was also found only for core samples from 116 cm left side of dike but abscent from right side indicating the remagnetization by the dike depends on the geometric shape and width of the dike, which is supported by field observations. The content of epidote is well correlated with remagnetization, and indicates the hydrothermal alteration/metameorphism was activated by the intrusion. We concluded that the above evidences in this study further support thermally-activated chemical origin of the remagnetization with meager contribution of contact metamorphism, and that any significant evidence of regional-scaled remagnetization was not found in the study area.

• 한국자기학회지
• /
• 제24권2호
• /
• pp.60-65
• /
• 2014

전기 도금법으로 제작한 Ni 박막(240 nm)의 자기장 각도에 따른 강자성 공명 신호를 측정하여 공명 자기장($H_{res}$) 및 선폭(${\Delta}H_{PP}$)을 도출하였다. 자기장 각도에 따른 $H_{res}$는 이론적인 분석 결과와 일치하였으며 이들 결과로부터 제조된 Ni 박막의 g-factor는 2.18임을 확인하였다. 자기장 각도에 따른 ${\Delta}H_{PP}$는 박막의 수평 방향에서 매우 큰 값을 나타냈으며, 이러한 특성은 Gilbert 감쇠에 기인하는 균일한 선폭 특성과 약 1 nm의 표면에서 나타나는 자구들의 각도 변화 및 자화량 변화에 기인하는 비균일한 선폭 특성으로는 설명되지 않았다. 따라서 본 연구에서는 박막의 두께가 10 GHz에서 임계 두께(약 50 nm) 이상으로 증가하면 나타나는 two magnon scattering 이론을 적용하여 비균일한 선폭 특성을 분석하였다. 이러한 분석 결과로부터 전기 도금법으로 제작한 240 nm 두께를 갖는 Ni 박막에서 각도에 따른 비균일한 선폭 변화의 주요한 원인은 재료 내부 결함들에 의한 스핀파 산란이었음을 알 수 있었다.