• Elastomers and Composites
• /
• 제44권3호
• /
• pp.315-322
• /
• 2009

이피디엠/폴리프로필렌 열가소성 경화물을 오일의 배합 순서를 달리한 두 가지 방식(오일 블렌드 후 가교방식과 가교 후 오일 블렌드 방식)으로 제조하여 가교도(겔분율), 경도, 인장강도, 신율, 용융흐름지수 등을 조사, 오일의 블렌드 방식이 열가소성 경화물의 물성에 미치는 영향을 알아보았다. 오일의 블렌드 방식에 따른 두 경화물의 가교도와 기계적 물성의 차는 크지 않았으나, 가공성에 있어서는 가교 후 오일 블렌드 방식으로 제조한 경화물의 용융흐름지수가 현저히 증가한 결과를 보였다.

• Journal of Mechanical Science and Technology
• /
• 제17권2호
• /
• pp.171-180
• /
• 2003

One of the most significant problems in the processing of composite materials is residual stress. The high residual stress may cause cracking in the matrix without external loads and degrade the integrity of composite structures. In this study, thermo-viscoelastic residual stresses occurred in an aluminum liner-inserted polymer composite cylinder are investigated. This type of the structure is used for rocket fuselage due to the convenience to attach payloads and equipment to the metal liner by machining. The time and degree of cure dependent thermo-viscoelastic constitutive equations are developed and coupled with a thermo-chemical process model. These equations are solved with the finite element method to predict the residual stresses in the composite cylinder and also in the interface between the liner and the composite during cure.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.83-87
• /
• 2004

In this work, the cure cycle of co-cured metal/composite structure was investigated to decrease fabricating thermal residual stresses between the metal and the composite material. DSC (Differential scanning calorimetry) experiment and static lap shear test of co-cured aluminum/composite double lap joint as well as the curvature experiment of co-cured steel/composite strip were performed to investigate the effect of curing cycle on the thermal residual stress of co-cured hybrid structures. From the experiments, it was found that post curing method after abrupt cooling of co-cured aluminum/composite hybrid structure at certain point of degree of cure during curing process could eliminate fabricating the thermal residual stresses.

• Bulletin of the Korean Chemical Society
• /
• 제20권11호
• /
• pp.1329-1334
• /
• 1999

The curing characteristics of diglycidyl ether of bisphenol A (DGEBA) with diaminodiphenylmethane (DDM) as a curing agent were studied using differential scanning calorimetry (DSC), rheometrics mechanical spectrometry (RMS), and dielectric analysis (DEA). The isothermal curing kinetics measured by DSC were well represented with the generalized auto-catalytic reaction model. With the temperature sweep, the inverse relationship between complex viscosity measured by RMS and ionic conductivity obtained from DEA was established indicating that the mobility of free ions represented by the ionic conductivity in DEA measurement and the chain segment motion as revealed by the complex viscosity measured from RMS are equivalent. From isothermal curing measurements at several different temperatures, the ionic conductivity contribution was shown to be dominant in the dielectric loss factor at the early stage of cure. The contribution of the dipole relaxation in dielectric loss factor became larger as the curing further proceeded. The critical degrees of cure, at which the dipolar contribution in the dielectric loss factor starts to appear, increases as isothermal curing temperature is increased. The dielectric relaxation time at the same degree of cure was shorter for a sample cured at higher curing temperature.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 춘계학술발표대회 논문집
• /
• pp.53-58
• /
• 2000

During the curing process of thick glass/epoxy laminates, a substantial amount of temperature lag and overshoot at the center of the laminates is usually experienced due to the large thickness and low thermal conductivity of the glass/epoxy composites. Also, it requires a longer time for full and uniform consolidation. In this work, temperature, degree of cure and consolidation of a 20mm thick unidirectional glass/epoxy laminate were investigated using an experiment and a 3-dimentional numerical analysis considering the exothermic reaction. From the experimental and numerical results, it was found that the experimentally obtained temperature profile agreed well with the numerical one and the cure cycle recommended by the prepreg manufacturer should be modified to prevent a temperature overshoot and to obtain full consolidation.

• 대한소아치과학회지
• /
• 제25권4호
• /
• pp.731-748
• /
• 1998

The purpose of this study was to test the hypothesis that the more thorough cure of lightactivated composite resin could be obtained if a new way of delivering the light source deep through the resin body is developed when compared to the conventional bulk cure or incremental cure. Using cylindrical resin blocks and natural teeth, various curing conditions were tested for their effects on the degree of microleakage and microhardness. Data were analyzed statistically using One-Way ANOVA and Scheff's Multiple Range test. The results of the present study were as follows: 1. The increment of reduction in microhardness with depth was shown to be higher in group I and II than in group II and V. 2. At the level of lower inner surface and the bottom surface, significantly lower microhardness values were obtained in group I and II when compared to group III, IV and V. Group IV showed the lowest value among three groups(III, IV, V) representing the only statistically significant difference from group V(p<05). 3. Differences between groups in the degree of microleakage detected were shown to be statistically significant (p<05) with the exception of group IV and V at both occlusal and gingival margins. 4. Based upon the above-mentioned results, commonly cited recommendation of incremental curing is strongly supported and the light-transmitting wedge insertion method can be considered as a effective and feasible clinical procedure for the better curing of composite resin. However, more studies under a variety of conditions should be completed before this method is applied actually to the clinical setting.

• Restorative Dentistry and Endodontics
• /
• 제36권2호
• /
• pp.132-138
• /
• 2011

연구목적: 본 연구는 3종의 이중중합 레진시멘트에서 자가중합법과 이중중합법이 중합도에 미치는 영향을 간접적으로 알아보고자 시간경과에 따라 미세경도를 측정하였다. 연구 재료 및 방법: 실험을 위해 자가접착 레진시멘트인 Maxcem Elite (Kerr)와 Rely-X Unicem (3M ESPE) 및 전통형 레진시멘트인 Rely-X ARC (3M ESPE)를 사용하였으며 각 레진시멘트를 동일한 크기의 테플론 몰드에 채우고 자가중합법과 이중중합법으로 중합을 하여 각각 10개씩 시편을 제작하였으며 중합 시작 후 10분, 30분, 1시간, 3시간, 6시간, 12시간, 24시간이 지난 시점에 미세경도를 측정하였다. 결과: 각 시점에서 레진시멘트별로 중합법 사이의 비교를 위한 independent samples t-test 및 모든 실험군 사이의 비교를 위한 one-way ANOVA와 Scheffe 사후검정을 95% 유의수준에서 실시하여 다음과 같은 결과를 얻었다. 1. 모든 실험군에서 시간이 경과함에 따라 미세경도가 증가하는 경향을 보였다. 2. Maxcem에서 중합 1시간 후 부터를 제외하고 이중중합이 자가중합에 비해 높은 미세경도 값을 보였다(p<0.05). 3. 매 시점에서 자가중합법의 Rely-X Unicem이 가장 낮은 미세경도를 보였으며 이중중합법의 Rely-X Unicem이 가장 높은 미세경도 값을 보였다. 결론: 이상의 실험 결과로 볼 때 이중중합 레진시멘트의 충분한 중합을 위해서는 광조사를 반드시 하여야 할 것으로 생각한다.

• 폴리머
• /
• 제37권1호
• /
• pp.121-126
• /
• 2013

4,4'-Thiodibenzenethiol을 기반으로 이관능 에폭시 수지인 4,4'-thiodibenzenethiol diglycidyl ether를 직접합성법으로 합성하였다. 합성된 에폭시 수지가 광경화가 가능하도록 acrylic acid와 반응시켜 광경화형 고굴절 이관능 에폭시 아크릴레이트인 4,4'-thiodibenzenethiol diglycidyl ether diacrylate를 합성하였으며 $^1H$ NMR과 FTIR을 이용하여 화학구조를 확인하였다. 이관능 에폭시 아크릴레이트와 함께 반응성 희석제인 2-phenoxythiol ethyl acrylate를 5, 10, 15, 20, 30 wt% 희석하여 점도와 굴절률과의 상관관계를 확인하였으며 광경화 후 경화필름의 굴절률 변화를 고찰 하였다. 반응성 희석제의 농도가 증가함에 따라 경화물의 경화도가 낮아졌으며, 경화도가 클수록 경화 후 굴절률은 높아지는 경향을 확인하였다.

• Elastomers and Composites
• /
• 제48권3호
• /
• pp.201-208
• /
• 2013

본 연구는 황과 가교 촉진제의 함량이 달리 적용된 acrylonitrile styrene-butadiene rubber (AN-SBR)/silica 컴파운드가 타이어 트레드 컴파운드의 특성에 미치는 영향에 대해 연구하였다. 실험 결과, 가교제 및 가교촉진제의 함량이 증가할수록 가교 반응성이 증대되어 가교속도 및 컴파운드의 가교도가 상승하였다. 또한 내마모 특성 뿐만 아니라 경도, 모듈러스와 같은 컴파운드의 기계적 특성은 높은 가교도에 기인하여 향상되었다. 동적 점탄 특성에서는 가교도의 증가와 함께 유리전이온도 ($T_g$)가 상승하여 $0^{\circ}C$ 영역에서의 tan ${\delta}$ 값이 향상되었고, $60^{\circ}C$ 영역에서의 tan ${\delta}$ 값이 감소되었다. 초기 가교 속도 ($t_1$)는 $60^{\circ}C$의 tan ${\delta}$ 값과 선형적인 관계를 나타내었다. 이는 가교제의 증량으로 초기 가교 속도 ($t_1$)가 빨라져 조기에 가교가 시작됨으로써 filler network 의 발달을 억제시킨 결과에 따른 것으로 판단된다. 이러한 결과는 AFM (atomic force microscopy)을 통하여 열처리된 컴파운드의 표면 관찰에서도 확인할 수 있었다. 따라서, 빠른 초기 가황 반응에 기인한 실리카의 re-agglomeration 감소는 $60^{\circ}C$에서의 tan ${\delta}$를 결정하는 매우 중요한 변수임을 알 수 있다.

• 대한정형도수물리치료학회지
• /
• 제11권2호
• /
• pp.83-95
• /
• 2005

The purpose of this study is to analyze, durability of motor effort after finishing rehabilitation program and the influence from the isotonic lumbar region extension exercise after an operation according to the different operation way in invasive degrees. We selected randomly 80 patients who have no complication and musculoskeletal system diseases with finishing the 12 weeks' rehabilitation program after getting laser discectomy, but fail to conservative treatment, about Lumbar HNP, and divided into minimal invasive groups 38 and invasive groups 42 for study. As the results, in minimal invasive group, after finishing cure and 6 months later, the degree of hold muscle of women is much better than that of men. but in Invasive group, that of men is better than that of women, in case of women, the $0^{\circ}$ and $72^{\circ}$ in lumbar flexion angle have weaken or no improvement than before beginning exercise. and muscle force in $72^{\circ}$ in lumbar flexion angle increased to all men and women than before beginning exercise in Minimal invasive group. but in invasive group. it decreased. When analyze the lapsed time in Minimal invasive group, the groups who start the exercise within 3 months are better than the groups who start the exercise above 3 months after an operation the hold muscle degree all angles after finishing cure and 6 months later. Meanwhile, in invasive group, the groups who start the exercise within 3 months are better than the groups who start the exercise above 3 months after an operation about the hold muscle degree in 36-72 of lumbar flexion angle but 0-36 are not good after finishing cure and 6 months later. When analyze BMI in Minimal invasive group, the normal groups are better than the overweight groups about hold muscle degree in all angles after finishing cure and 6 months later.