• Journal of Korean Society of Rural Planning
• /
• v.11 no.4 s.29
• /
• pp.67-74
• /
• 2005

The Doam watershed is located at alpine areas and the annual average precipitation, including snow accumulation, is significant higher than other areas. Thus, pollutant laden runoff and sediment discharge from the alpine agricultural fields are causing water quality degradation at the Doam watershed. To estimate soil erosion from the agricultural fields, the Universal Soil Loss Equation (USLE) has been widely used because of its simplicity to use. In the early spring at the Doam watershed, the stream flow increases because of snow melt, which results in erosion of loosened soil experiencing freezing and thaw during the winter. Also, extremely torrential rainfall, such as the typhoons 'RUSA' in 2002 and 'MAEMI' in 2003, caused significant amounts of soil erosion and sediment at the Doam watershed. However, the USLE model cannot simulate impacts on soil erosion of freezing and thaw of the soil. It cannot estimate sediment yield from a single torrential rainfall event. Also, it cannot simulate temporal changes in USLE input parameters. Thus, the Soil and Water Assessment Tool (SWAT) model was investigated for its applicability to estimate soil erosion at the Doam watershed, instead of the widely used USLE model. The SWAT hydrology and erosion/sediment components were validated after calibration of the hydrologic component. The R$^2$ and Nash-Sutcliffe coefficient values are higher enough, thus it is found the SWAT model can be efficiently used to simulate hydrology and sediment yield at the Doam watershed. The effects of snow melt on SWAT estimated stream flow and sediment were investigated using long-term precipitation and temperature data at the Doam watershed. It was found significant amount of flow and sediment in the spring are contributed by melting snow accumulated during the winter. Two typhoons in 2002 and 2003, MAEMI and RUSA, caused 33% and 22% of total sediment yields at the Doam watershed, respectively. Thus, it is recommended that the SWAT model, capable of simulating snow melt, sediment yield from a single storm event, and long-term weather data, needs to be used in estimating soil erosion at alpine agricultural areas to develop successful soil erosion management instead of the USLE.

• Journal of Korean Society of Steel Construction
• /
• v.29 no.2
• /
• pp.147-158
• /
• 2017

The present study focused on the structural performance of newly developed prefabricated composite columns (PSRC composite column) using bolt-connected steel angles. Concentric axial loading tests were performed for four 2/3 scaled PSRC column specimens and two conventional SRC column specimens. The test parameters were the spacing and sectional configurations of lateral reinforcement, and width-to-thickness ratio of steel angles. The test results showed that the axial load-carrying capacity and deformation capacity of the PSRC column specimens were comparable to those of the conventional SRC column specimens. Closely spaced steel plates and Z-shaped steel plates for lateral reinforcement increased the deformation capacity of the PSRC column specimens. The load-carrying capacity was greater than the prediction by current design codes. Numerical analysis was performed for the specimens. The results agreed well with the test results in terms of initial stiffness, load-carrying capacity, except for strength degradation due to cover concrete spalling.

• Journal of the Korean Society of Radiology
• /
• v.12 no.4
• /
• pp.497-503
• /
• 2018

The purpose of this study was to investigate the degree of image degradation and the improvement of image quality caused by the density difference between the orthodontic filling material and the surrounding anatomical structure during the examination of the facial CT by quantitative and qualitative analysis. The teeth were scanned using 64-MDCT (Discovery 750 HD, GE HEALTH CARE, Milwaukee, USA). The teeth were scanned and compared according to tube voltage, silicone application, and MAR application. As a result, 10.36% CT value decreased at 140 kVp and 5.81% decrease at the application of silicon material. As a result of the qualitative evaluation, it was evaluated that 7 of the 10 observers and 3 of the acceptors were applied to the MAR algorithm. Therefore, it is possible to reduce the unnecessary burden on the radiation exposure dose as well as to reduce the loss of image data by reducing the high density artifacts, as well as the inspection parameters used in the current clinical application and various algorithms that can reduce the high density artifacts. It can be expected to provide a lot of image information.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.27 no.4
• /
• pp.246-257
• /
• 2015

The progressive degradation paths of structures have quantitatively been tracked by using stochastic processes, such as Wiener process, gamma process and compound Poisson process, in order to consider both the sampling uncertainty due to the usual lack of damage data and the temporal uncertainty associated with the deterioration evolution. Several important features of stochastic processes which should carefully be considered in application of the stochastic processes to practical problems have been figured out through assessing cumulative damage and lifetime distribution as a function of time. Especially, the Wiener process and the gamma process have straightforwardly been applied to armors of rubble-mound breakwaters by the aid of a sample path method based on Melby's formula which can estimate cumulative damage levels of armors over time. The sample path method have been developed to calibrate the related-parameters required in the stochastic modelling of armors of rubble-mound breakwaters. From the analyses, it is found that cumulative damage levels of armors have surely been saturated with time. Also, the exponent of power law in time, that plays a significant role in predicting the cumulative damage levels over time, can easily be determined, which makes the stochastic models possible to track the cumulative damage levels of armors of rubble-mound breakwaters over time. Finally, failure probabilities with respect to various critical limits have been analyzed throughout its anticipated service life.

• Textile Coloration and Finishing
• /
• v.30 no.2
• /
• pp.117-129
• /
• 2018

Cellulose has been widely applied into various medical fields including scaffolding, tissue engineering and tissue formation. In this study, we manufactured cellulose medical fiber from Styela clava tunics(SCT-CS) and analyzed the tensile strength, elongation at break, fluid uptake and surface morphology. And then, the biocompatibility and toxicity of SCT-CS were measured in Sprague-Dawley(SD) rats after the implantation for 30, 60 and 90 days. The level of tensile strength and fluid uptake were lower in SCT-CS than chromic catgut(CCG), while elongation at break level were maintained the higher in SCT-CS. Also, the roughness with pronounced surface patterns as a result of in vivo degradation was significantly greater in CCG than this of SCT-CS although these levels gradually appeared with time in both groups. After implantation for 90 days, SCT-CS and CCG was successfully implanted around muscle of thigh without any significant immune response. Furthermore, no significant alterations were measured in serum parameters and the specific pathological features induced by most toxic compounds for liver and kidney toxicity. Therefore, these results suggest that SCT-CS showing good biocompatibility and non-toxicity can be successfully prepared from cellulose powder of SCT as well as has the potential for use as a powerful biomaterial for medical sutures.

• Korean Journal of Environmental Agriculture
• /
• v.29 no.2
• /
• pp.197-205
• /
• 2010

This study was conducted to investigate the optimum conditions for efficient methane production through anaerobic digestion of pig waste slurry. The examined parameters were organic matter content of the pig slurry, the ratio of seed sludge to pig slurry, and stirring intensity of the digestion reactor. The effects of types of slurry produced from different purpose-based pigs fed with different feeds were also tested. The methane concentration in the produced biogas was 45% when the ratio of seed sludge to pig slurry was 50% and total solid (TS) concentration was 1%, and it increased in proportional to TS concentration increases from 3 to 7%. At 3 and 5% of TS concentration, increasing mixing velocity from 80 to 160 rpm resulted in higher biogas production amount. However, mixing amount of seed sludge did not cause any significant effect on biogas production. Overall, the most efficient biogas production was achieved at 3-5% TS concentration in combination with 50% seed sludge inoculation and mixing velocity at 120 rpm. Among pig slurry types, gestating sow waste slurry showed the highest biogas production probably due to higher the degradation rate than other types of pig waste slurry being affected by the feeds components.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.24 no.2
• /
• pp.51-58
• /
• 2016

In the Integrated Two-Phase Anaerobic Digestion (ITPAD) process, acid and methane fermentation take place in one reactor, which has advantages to cope with organic load variation and reduce foot-print required, compensating disadvantages of Conventional Separated Two-Phase Anaerobic Digestion (CSTPAD). In the present work, organic matter degradation efficiency and biogas generation amount and other performance parameters of the ITPAD fed with food waste leachate were analyzed. In addition, feasibility study on the ITPAD method was performed by comparing its digestion efficiency with that of the CSTPAD. Organic matter alteration and biogas generation of the integrated method were examined for approximately 130 days based on the 5ton/day scaled pilot plant. Experiment results revealed that organic matter removal rate was 80% for mean food waste leachate input amount of $4.1m^3/day$. The biogas generation rate was $63.0m^3$ per ton of food waste leachate input, corresponding to the input VS amount of $0.724m^3/kg-VS_{added}$, and methane content of generated biogas was approximately 61.3%. The ITPAD has a comparable or higher organic matter removal efficiency compared to the conventional separated two-phase anaerobic digestion method. Consequently, the ITPAD method has a great need to commercialize a food waste leachate treatment technology against highly concentrated organic waste leachate.

• Asian-Australasian Journal of Animal Sciences
• /
• v.31 no.2
• /
• pp.230-236
• /
• 2018

Objective: Two ex vivo experiments were conducted to verify the effect of barley grain (Nusrat cultivar) treated with alkaline compounds (AC) including alum, ammonium, and sodium hydroxide or cation-exchanged organic extracts (OE) prepared from alfalfa hay, sugar beet pulp and Ulva Fasciata, on extent and digestion of starch. Methods: In the first study, the in vitro first order disappearance kinetic parameters of dry matter (DM), crude protein (CP) and starch were estimated using a non-linear model ($D_{(t)}=D_{(i)}{\cdot}e^{(-k_d{\cdot}time)}+I$, where: $D_{(t)}$ = potentially digestible residues at any time, $D_{(i)}$ = potentially digestible fraction at any time, $k_d$ = fractional rate constant of digestion (/h), I = indigestible fraction at any time). In the second experiment, the ruminal and post-ruminal disappearance of DM, CP, and starch were determined using in situ mobile nylon bag. Results: Barley grains treated with alum and alfalfa extract had a higher constant rate of starch digestion (0.11 and 0.09/h) than others. Barley grain treated with OE had a higher constant rate of CP digestion and that of treated with AC had a higher constant rate of starch digestion (0.08 and 0.11/h) compared with those of the other treatments. The indigestible fraction of starch treated with alum and sugar beet pulp extract was higher than that of the control group (0.24 and 0.25 vs 0.21). Barley grain treated with AC and OE had significant CP disappearance in the rumen, post-rumen and total tract, and also starch disappearance for post-rumen and total tract compared with the untreated (p<0.001). Conclusion: This study demonstrated that AC and OE might have positive effects on the starch degradation of the barley grain. In addition, treating barley grain with alum and sugar beet pulp extract could change the site and extend digestion of protein and starch.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.23 no.2
• /
• pp.47-52
• /
• 2015

A microbial fuel cell (MFC) is a device that can be obtained electricity from a variety of organic through the catalytic reaction of the microorganism. The MFC can be applied to various fields, and research is required to promote the performance of the microbial fuel cell for commercialization. The lower performance of an MFC is due to oxygen reduction at the cathode and the longer time of microbial degradation at anode. The MFC amount of power is sufficient but, in consideration of many factors, as a renewable energy, now commonly power density as compared to Nafion117 it is an ion exchange membrane used is PP (Poly Propylene) from 80 to about 11 fold higher, while reducing the cost to process wastewater is changed to a microporous non-woven fabric of a low cost, it may be energy-friendly environment to generate electricity. All waste, in that it can act as a bait for microorganisms, sustainability of the microbial fuel cell is limitless. The latest research on the optimization and performance of the operating parameters are surveyed and through the SSaM-GG(Smart, Shared, and Mutual- Green Growth) or GG-SSaM(Green Growth - Smart, Shared, and Mutual) as the concept of sustainable development in MFC, the middle indices are developed in this study.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.3
• /
• pp.32-39
• /
• 2009

In this paper, system optimization design technique of an impulse ground penetrating image radar (GPIR) in time domain is proposed to improve depth resolution of the system. For the purpose, time domain analysis method of key components such as impulse generator and UWB antenna is explained and by simulation, parameters of each component are determined. In particular, by standardizing the impulse signal, spectrum efficiency of a radiated impulse signal is improved and a U-shaped planar dipole antenna for a UWB antenna is developed. By equipping a parabolic metal reflector with the proposed antenna, external noise is prevented and the ability of radiating an input impulse into ground is improved. In addition, to remove ringing effect of the propose antenna which causes serious degradation of the system performance, resistors are loaded at the edge of the antenna and then Tx and Rx UWB antennas are optimized by simulation in time domain. For images of targets buried under the ground migration technique is applied and influence of tough ground surface on distortion of received impulse signals is reduced using technique of noise and signal distortion reduction in time domain and its time resolution is enhanced. To verify the design optimization procedure, a prototype of an GPIR and an artificial test field are made. Measurement results show that the resolution of the system designed is as good as that of a theoretical model.