• Geomechanics and Engineering
• /
• v.3 no.2
• /
• pp.117-130
• /
• 2011

The methods of design available for geocell-supported embankments are very few. Two of the earlier methods are considered in this paper and a third method is proposed and compared with them. In the first method called slip line method, plastic bearing failure of the soil was assumed and the additional resistance due to geocell layer is calculated using a non-symmetric slip line field in the soft foundation soil. In the second method based on slope stability analysis, general-purpose slope stability program was used to design the geocell mattress of required strength for embankment. In the third method proposed in this paper, geocell reinforcement is designed based on the plane strain finite element analysis of embankments. The geocell layer is modelled as an equivalent composite layer with modified strength and stiffness values. The strength and dimensions of geocell layer is estimated for the required bearing capacity or permissible deformations. These three design methods are compared through a design example. It is observed that the design method based on finite element simulations is most comprehensive because it addresses the issue of permissible deformations and also gives complete stress, deformation and strain behaviour of the embankment under given loading conditions.

• Journal of Fisheries and Marine Sciences Education
• /
• v.28 no.5
• /
• pp.1470-1477
• /
• 2016

This study has designed and evaluated the safety of watertight damper for Offshore Rigs. The watertight damper is an improved design for conventional DN 350 butterfly valve. Numerical analysis has been performed to investigate the safety factor and seat leakage of the designed 3-type disk dampers. The structure analysis results present the deformations, the equivalent stresses and the safety factor. It was confirmed that the designed disk, rib-disk and streamlined disk of watertight damper are safe enough in maximum operating pressure of 0.98MPa. The results show that the disk damper had the smallest maximum deformations and stress among 3-type disk dampers and the safety factor was 4.3. Therefore it is confirmed that the disk damper has the most excellent strength. Also linear static structural analysis was individually conducted for disk and body. The results show that the maximum disk deformation was larger than the body deformation, Therefore the disk damper is causes no seat leakage.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2002.04a
• /
• pp.19-26
• /
• 2002

In this paper, the nonlinear structural analysis for the composite structure of the spent nuclear fuel disposal container and the 50cm thick bentonite buffer is carried out to predict the collapse of the container while the sudden rock movement of 10cm is applied on the composite structure. This sudden rock movement is anticipated by the earthquake etc. at a deep underground. Horizontal symmetric rock movement is assumed in this structural analysis. Elastoplastic material model is adopted. Drucker-Prager yield criterion is used for the material yield prediction of the bentonite buffer and von-Mises yield criterion is used for the material yield prediction of the container(cast iron insert, copper outer shell and lid and bottom). Analysis results show that even though very large deformations occur beyond the yield point in the bentonite buffer, the container structure still endures elastic small strains and stresses below the yield strength. Hence, the 50cm thick bentonite buffer can protect the container safely against the 10cm sudden rock movement by earthquake etc.. Analysis results also show that bending deformations occur in the container structure due to the shear deformation of the bentonite buffer. The elastoplastic nonlinear structural analysis for the composite structure of the container and the bentonite buffer is performed using the finite element analysis code, NISA.

• Earthquakes and Structures
• /
• v.2 no.1
• /
• pp.65-88
• /
• 2011

A new method for the seismic design of plane steel moment resisting frames is developed. This method determines the design base shear of a plane steel frame through modal synthesis and spectrum analysis utilizing different values of the strength reduction (behavior) factor for the modes considered instead of a single common value of that factor for all these modes as it is the case with current seismic codes. The values of these modal strength reduction factors are derived with the aid of a) design equations that provide equivalent linear modal damping ratios for steel moment resisting frames as functions of period, allowable interstorey drift and damage levels and b) the damping reduction factor that modifies elastic acceleration spectra for high levels of damping. Thus, a new performance-based design method is established. The direct dependence of the modal strength reduction factor on desired interstorey drift and damage levels permits the control of deformations without their determination and secures that deformations will not exceed these levels. By means of certain seismic design examples presented herein, it is demonstrated that the use of different values for the strength reduction factor per mode instead of a single common value for all modes, leads to more accurate results in a more rational way than the code-based ones.

• Elastomers and Composites
• /
• v.47 no.4
• /
• pp.272-281
• /
• 2012

Flexible/stretchable electronics have recently focused, since their applications extend to emerging flexible displays, sensors, dielectric elastomer actuator and generators, and smart surgical tools. Flexible/stretchable electrodes should be synchronized with employing mechanical deformations of either flexing or stretching modes. Thus, the research area is one of the tough subjects, since the electrodes should keep their basic functions of electrodes under various mode of mechanical deformations. In this review, we discuss the recent development in the preparation and properties of such flexible/stretchable electrodes.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.4
• /
• pp.37-47
• /
• 1999

A Finite Volume Method for the discretization of the two-dimensional incompressible Navier-Stokes equation is used to analyse water entry & exit problems in a generalized coordinate system. The free-surface deformations generated by the water entry or exit of a rigid body are simulated by the Level-Set scheme[11]. In the water entry problems for a wedged section and a flared-ship section, the calculation results of water impact force are compared with the experimental results[5] and the time varying free-surface deformations and flow characteristics of the water exit of a cylinder are investigated.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.1 no.2
• /
• pp.95-100
• /
• 2009

As ships become larger, thicker and higher tensile steel plate are used in shipyard. Though special chemical compositions are required for high-tensile steels, recently they are made by the TMCP (Thermo-Mechanical control process) methodology. The increased Yield / Tensile strength of TMCP steels compared to the normalized steel of same composition are induced by suppressing the formation of Ferrite and Pearlite in favor of strong and tough Bainite while being transformed from Austenite. But this Bainite phase could be vanished by another additional thermal cycle like welding and heating. As thermal deformations are deeply related by yield stress of material, the study for prediction of plate deformation by heating should niflect the principle of TMCP steels. The present study is related to the development of an algorithm which could calculate inherent strain. In this algorithm, not only the mechanical principles of thermal deformations, but also the initial portion of Bainite is considered when calculating inherent strain. Distortion analysis results by these values showed good agreements with experimental results for normalized steels and TMCP steels during welding and heating. This algorithm has also been used to create an inherent strain database of steels in Class rule.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.2
• /
• pp.123-133
• /
• 2003

A practical statistical approach that can be used to model various sources of uncertainty systematically is presented in the context of reliability analysis of slope stability. New expressions for probabilistic characterization of soil properties incorporate sampling and measurement errors, as well as spatial variability and its reduced variance due to spatial averaging. The stochastic nature of seismic loading is studied by generating a large series of hazard-compatible artificial motions, and by using them in subsequent response analyses. The analyses indicate that in a seismically less active region such as the Korean Peninsular, a moderate variability in soil properties has an effect as large as the characterization of earthquake hazard on the computed risk of slope failure and excessive slope deformations.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.5 no.3
• /
• pp.173-180
• /
• 2001

In the past few years, the nondestructive inspection technology has greatly developed due to the increased necessity to gain a complete understanding of the bridge behavior. Especially, the deformations of bridges contain a lot of informations about its health state. By measuring these deformations it is possible to analyze the loading and aging behavior of the structure. However, the current, methods (such as LVDT, dial gage, optical displacement transducer, etc) are often of changeable application on site and have the limitations of installation. In this paper, the classical beam theory was reviewed and the deflections of structure are estimated using measured strain which is easy to acquire. The applicability of this algorithm is verified by laboratory(simple reinforced concrete beam) and field test. By this test, we proposed correction factor to estimate deflection of reinforced concrete beam after cracking, and analyze about the generation of correction factor. Also fiber optic sensors as well as resistive strain gages were installed in the concrete beams to establish the applicability of fiber optic sensors in the field of civil engineering.

• Design & Manufacturing
• /
• v.11 no.3
• /
• pp.13-18
• /
• 2017

The injection molding analysis of VCM (Voice Coil Motor) housing for smart phone cameras were performed. We conducted the analysis in terms of injection molding pressure, the formation of weld lines, flow marks, and flow patterns. The goal of the analysis was targeted for the prediction of the optimal gate locations. Because the quality of VCM housing is strongly dependent on the precise control of the camera lens by its nature, we focused on the lens guiding lanes in the VCM housing. We first calculated the maximum injection molding pressure in terms of the filled volumes. The injection molding pressure were calculated within 146MPa at about 90% volume filled. We also investigated the possibility of the occurrence of design-related defects such flow marks, weld lines. Filling patterns regarding the design of the gate locations were delineated to find the weld lines. Throughout the simulations, the final deformations of the lens guiding lanes for the VCM housing were calculated. The deformations distribute ranging from $0.5{\mu}m$ to $2.50{\mu}m$, which were used to find the optimal design of the gates.