• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.112-113
• /
• 2019

Recently, supplementary cementitious materials such as blast-furnace slag, fly ash and silica fume have been widely used as substitutes for cementitious materials. In this study, the deformation behavior of compressive loading of C₃S paste with 50% fly ash was analyzed by X-ray scattering data and pair distribution function analysis. The obtained results were compared with 131-day-old pure C₃S paste. The Ca(OH)₂ of the C₃S-FA paste showed almost complete elastic behavior, consistent with the deformation behavior of the r-range of 20 to 40, and the C-S-H phase contributed to the range of PDF r-range of less than 20. In addition, C-S-H of C₃S-FA showed greater deformation resistance than C₃S paste.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.27 no.1
• /
• pp.49-57
• /
• 2023

This study investigated the rocking behavior of unreinforced masonry walls and wall piers under cyclic loading. Based on the benchmark tests, the characteristics of load-deformation relations in masonry walls with rocking failure were captured, focusing on observed deformation modes. The rocking strengths of masonry walls (i.e., peak and residual strengths) were evaluated, and the effects of opening configurations on the masonry wall strength were examined. The deformation capacity of the rocking behavior and the hysteresis shape of the load-deformation relations were also identified. Based on the results, modeling approaches for the rocking behavior of masonry walls were discussed.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.292-297
• /
• 2003

A stochastic approach has been presented for superplastic deformation of Ti-6AJ-4V alloy, and probability function are used to heterogeneous phase distributions. The experimentally observed spatial correlation function are developed, and microstructural evolutions together with superplastic deformation behavior have investigated by means of the probability function. The result have shown that the probability varies approximately linearly with separation with distance, and significant deformation enhanced probability changes during the deformation. The stress-strain behavior with the evolutions of probability function can be correctly predicted by the model. The finite clement implementation using Monte Carlo simulation associated with phase re-distributions shows that better agreement with experimental data of failure strain on the test specimen.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.10 s.241
• /
• pp.1344-1352
• /
• 2005

Densification behavior of iron powder under cold stepped plastic deformation was studied. Experimental data were also obtained for iron powder under cold stepped plastic deformation. The elastoplastic constitutive equation based on yield function of Shima and Oyane was implemented into a finite element program (ABAQUS) to simulate compaction responses of i.on powder during cold stepped plastic deformation. Finite element calculations were compared with experimental data for densification, deformed geometry and density distribution. The agreement between finite element results and experimental data was good for iron powder.

• Earthquakes and Structures
• /
• v.26 no.3
• /
• pp.203-218
• /
• 2024

Beam-column joints in the frame structure are at high risk of brittle shear failure which would lead to significant residual deformation and even the collapse of the structure during an earthquake. In order to improve the damage issue and enhance the recoverability of the beam-column joints, a sector lead rubber damper (SLRD) has been developed. The SLRD can increase the bearing capacity and energy dissipation capacity, and also demonstrating recoverability of seismic performance following cyclic loading. In this paper, the hysteretic behavior of SLRD was experimentally investigated in terms of the regular hysteretic behavior, large deformation behavior and fatigue behavior. Furthermore, a parametric analysis was performed to study the influence of the primary design parameters on the hysteretic behavior of SLRD. The results show that SLRD resist the exerted loading through the shear capacity of both rubber parts coupled with the lead cores in the pre-yielding stage of lead cores. In the post-yielding phase, it is only the rubber parts of the SLRD that provide the shear capacity while the lead cores primarily dissipate the energy through shear deformation. The SLRD possesses a robust capacity for large deformation and can sustain hysteretic behavior when subjected to a loading rotation angle of 1/7 (equivalent to 200% shear strain of the rubber component). Furthermore, it demonstrates excellent fatigue resistance, with a degradation of critical behavior indices by no more than 15% in comparison to initial values even after 30 cycles. As for the designing practice of SLRD, it is recommended to adopt the double lead core scheme, along with a rubber material having the lowest possible shear modulus while meeting the desired bearing capacity and a thickness ratio of 0.4 to 0.5 for the thin steel plate.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.9
• /
• pp.62-69
• /
• 2000

Uneven clearances in the left and right sides of a press die cause deformation of the punch in precision shearing process. This deformation results from the compression stress and bending moment from shearing force in vertical direction and from the side force in horizontal direction acting to the punch, In this study the behavior of punch deformation is investigated in order to clarify the deformation state of the punch by using strain gauge deformation to shearing force side force bending moment radius of curvature and shear plane of the punch. Also we presented the calculation method of deformation size for the punch.

• Journal of Korea Foundry Society
• /
• v.37 no.5
• /
• pp.157-163
• /
• 2017

In the present study, the microstructural evolution and deformation behavior of AA 2014 aluminum alloys with different microstructures in a semi-solid state were investigated. For a given alloy, applied load and deformation time, the measured strain was higher at a higher temperature, indicative of a lower solid fraction. When a large proportion of the liquid was present as intragranular droplets, the alloy would not as easily deform because the effective liquid fraction between the solid grains had decreased. Greater deformation was achieved with higher grain boundary misorientations due to the enhanced wetting of the grain boundaries with liquid. A semi-empirical constitutive model is proposed for semi-solid deformation under the conditions in the present study. The mechanism of semi-solid deformation incorporates the initial flow of the liquid in the early stages of deformation, followed by a more gradual increase in the strain due to deformation by grain sliding accompanied by self-diffusion in the solid grains.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.10a
• /
• pp.228-231
• /
• 1997

A series of load relaxation tests was performed to determine stress-strain rate curves at high temperatures. Constitutive parameters of GBS and GMD were evaluated from the curves using the recently proposed inelastic deformation theory. Tensile tests and Microsturcture investigations showed deformation behavior as the relaxation test results predicted.

• Tunnel and Underground Space
• /
• v.22 no.3
• /
• pp.181-187
• /
• 2012

Many researches on disaster prevention using computer simulation methods can be performed to minimize the damage of property and to protect human life. Discontinuous deformation analysis (DDA) is a new computer simulation method to analyze the behavior of discontinuous rock masses. Since most rock slope problems are 3-dimensional in nature, 2-dimensional deformation analysis has limited application. In this study, the basic principles of 3-dimensional discontinuous deformation analysis are described. The newly developed 3-dimensional discontinuous deformation analysis method is proposed as the computer simulation method for discontinuous rock masses. Then, the failure behavior of rock slopes are simulated using 3-dimensional discontinuous deformation analysis. The simulation results are compared and examined with the failure behavior at the rock slopes. The results show the applicability of 3-dimensional discontinuous deformation analysis to analyze the deformation and failure mechanisms of rock slopes.

• Transactions of Materials Processing
• /
• v.27 no.2
• /
• pp.123-129
• /
• 2018

In the present study, the mechanical behavior of the spray-formed high speed steel was investigated employing the internal variable theory of inelastic deformation. Special attention was focused on the effect of the microstructure evolution during the hot working process, such as the distribution of carbides to provide a basic database for the production condition of high speed steels with excellent properties. The billets of high speed steel ASP30TM were fabricated by a spray forming, and the subsequently hot-rolled and heat-treated process to obtain uniformly distributed carbide structure. As noted the spray-formed high speed steel showed relatively coarser carbides than hot-rolled and heat-treated one with fine and uniformly distributed carbide structure. The step strain rate tests and high temperature tensile tests were carried out on both the spray-formed and the hot-rolled specimens, to elucidate their high temperature deformation behavior. The spray-formed high speed steel showed much higher flow stress and lower elongation than the hot-rolled and heat-treated steel. During the tensile test at $900^{\circ}C$, the interruption of the deformation for 100 seconds was conducted to reveal that the recovery was a main dynamic deformation mechanism of spray formed high speed steel. The internal variable theory of the inelastic deformation was used to analyze data from the step strain rate tests, revealing that the activation energies for hot deformation of as-spray-formed and hot-worked steels, which were 157.1 and 278.9 kJ/mol, and which were corresponding to the dislocation core and lattice diffusions of ${\gamma}-Fe$, respectively.