• Korean Journal of Materials Research
• /
• v.9 no.3
• /
• pp.327-332
• /
• 1999

The recovery activation energy, the order of reaction and the recovery rate constant were detemined by isochronal and isothermal annealing treatment to investigate the recovery behaviors of neutron irradiated Mn-Mo-Ni low alloy steels$(fluence: 2.3\times10^{19}ncm^{-2}, 553K, E\geq1.0 MeV)$. Vickers microhardness tests were conducted to trace the recovery behavior after heat treatments. The results were analyzed in terms of recovery stages, behavior of responsible defects and recovery kinetics. It was shown that recovery occurred through two annealing stages(stage I : 703-753K, stage n : 813-873K) with re$\infty$very activation energies of 2.5 eV and 2.93 eV for each stage I and n, respectively. From the comparison of unirradiated and irradiated isochronal anneal curves, a radiation anneal hardening(RAH) peak was identified at around 813K. Most of recovery have occurred during about 120 min irrespective of isothermal annealing temperatures of 743K and 833K. Recovery rate constants were determined to be $3.4\times10^{-4}min^{-1} and 7.1\times10^{-4}min^{-1}$ for stage I and II, respectively. The order of reaction was about 2 for both recovery stages. Comparing the obtained data with those of previously reported results on neutron irradiated Mn- Mo- Ni steels, the thermal recovery be­havior of the present material seems to occur by the dissociation of point defect clusters formed during irradiation, and by the recombination process of self-interstitials and vacancies from dissociated vacancy clusters.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.1 s.129
• /
• pp.7-16
• /
• 2005

This study was carried out to evaluate the structural property of double shear bolted connections in Korean Larch. For the main member, sawn lumber and Glulam were used in which thickness of lumber is 39 mm, 89 mm, 139 mm, 189 mm and Glulam 80 mm, 140 mm, 170 mm. For the side member, sawn lumber and steel plate were used in which thickness of lumber is the same of the main member and steel plate is 6mm. And connections were jointed by M12, M16, M20 bolts which were usually used for wood constructions in Korea. Directions of loading to connections were perpendicular and parallel to grain of main and side member. First, through the dowel bearing test, the dowel bearing strength was evaluated and through the bolt bending tests, the bolt bending strength was evaluated. And then experiments for the connection were performed. Obtained results from experiments were compared with calculated values by EYM and analyzed. Strength of double shear bolted connections in Korean Larch was similar or higher than calculated value by EYM. Especially when the side member was made by the sawn lumber, it was similar to the calculated value. In failure mode, the mode was effected by the knot and the dry defect. In the thin main member, it was shown mode I and as the thickness of the main member was thicker, it was changed into mode III.

• Childhood Kidney Diseases
• /
• v.14 no.1
• /
• pp.71-78
• /
• 2010

Purpose : Hydronephrosis is found about 30% of children with urinary tract infection (UTI). It can be caused by various conditions, although most childhood hydronephrosis is congenital. This study was performed to investigate the relationship between febrile UTI and hydronephrosis. Methods : We retrospectively reviewed the medical charts of 183 patients diagnosed as UTI between January 2007 and May 2009 at Korea University Guro Hospital. Inclusion criteria were as followings; 1) fever more than $37.5^{\circ}C$ measured in the axilla, 2) positive urine culture, 3) no history of urinary tract anomaly on antenatal sonography and urinary tract infection. We classified the enrolled children into two groups of patients with hydronephrosis (HN) and those without hydronephrosis (NHN). Results : The 80 patients were HN and 103 patients NHN. Hydronephrosis was found in 58 patients with left kidney, 8 right and 14 both kidneys. Most of hydronephrosis were of low grade. Compared with NHN group, initial renal cortical defects on DMSA scan significantly increased in HN group (HN 37.5%, NHN 16.5%, P<0.05). The incidence of VUR was not different between the two groups (HN 22%, NHN 12.1%). White blood cell counts and C-reactive protein were not different between the two groups. Follow-up DMSA scan (about 6 months later after UTI) showed no difference of renal scarring in both two groups. Conclusion : Our data suggests that hydronephrosis in febrile UTI patients is clinically useful for detecting renal cortical defects, but is not associated with follow-up renal scar.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.499-508
• /
• 2016

Injection molding is a method for manufacturing many products, wherein a plasticized resin is injected into a mold at high pressure and hardened. According to the method, the product can be manufactured into various forms, and the mass production of up to tens of thousands of products is possible. The purpose of this study was to determine the process conditions for manufacturing a door latch for automobiles, through an analysis of the injection molding method. To calculate an appropriate injection flow for injection molding, a primary analysis for comparing the injection time, pressure, flow pattern, consolidation range, shear stress, shear rate, and weld line, as well as a secondary analysis for determining the conditions for stabilizing the molding temperature, holding pressure, and cooling process, were conducted. The characteristics of injection molding, and their influence on the product quality are discussed. No weld line and pores were observed on the products that had been manufactured based on the process conditions determined above. In addition, there were no flaws regarding the deformation compared to the prototype. Therefore, the manufacture of a product under the conditions determined in this study can reduce the defect rate compared to the existing production, and the process is also more competitive due to reduced production time.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.280-288
• /
• 2016

This study proposes improved welding tools for magnesium alloys. Two types of tools were used for friction stir welding (FSW). The effect of the welding tools on the FSW joints was investigated with a fixed welding speed of 200mm/min and various rotation speeds of 400 to 800 rpm. After FSW, the joints were cross-sectioned perpendicular to the welding direction to investigate the defects. A tensile test and Vickers hardness test were conducted to identity the mechanical properties of the joints. Defects were observed when the rotation speed was 400 rpm, regardless of the welding tool, and the amount of defects tended to decrease with increases in rotational speed. Defect-free welds were obtained when the rotation speed was 800 rpm. The best weld quality was acquired using the C type welding tool. The rotation speed of 800 rpm and welding speed of 200 mm/min produced the best joining properties. The ultimate tensile strength, yield strength, and elongation of the welded region were 90.0%, 69.1%, and 83.2% those of the base metal, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.653-659
• /
• 2017

In this study, the complex forging process of an outer support ring was developed and the prototype was manufactured. The current process, hot forging and MCT machining, has a disadvantage of excessive material removal rates and longer machining hours. To overcome this disadvantage, a general shape is given through hot forging and the precision is achieved through cold forging. The complex forging process was developed with the minimal machining process. Forging analysis was carried out to design a forging process using the commercial program, Deform-3D. The hot and cold forging processes were set up based on the analyzed result. The mold and prototype were manufactured. Hardness, surface roughness, internal defect, the grain low line of the prototype were evaluated. The results showed no particular problems, and there were no problems in mass production. Using complex forging, the material was reduced by approximately 27 % compared to the process using hot forging and MCT machining. In addition, the production speed was improved 2.15 fold compared to that of hot forging and MCT machining. Through this study, a cost-effective process and mold design technology were established, which is expected to have positive effects on other related automotive parts production.

• Restorative Dentistry and Endodontics
• /
• v.25 no.2
• /
• pp.170-179
• /
• 2000

The rh-BMP-4 is a subgroup of TGF-${\beta}$ superfamily. The application of rh-BMP in alveolar bony defect was reported to new alveolar bone and new cementum formation. For minimized complications following tooth replantation, a operator must replant a tooth fast at the pertinent position. This study was to evaluate the effect of rh-BMP-4 on periodontal regeneration and root resorption following tooth replantation in rats. The 50 Sprague-Dawley rats weighting about 130gm were used in this study. The animals were divided into three groups. Group 1 ; immediate replantation after extraction : Group 2 ; replantation stored teeth extraction of first molar, the removal of periodontal ligament with collagenase, and etching with citric acid : Group 3 ; replantation stored teeth with treated rh-BMP-4 in mesial root. Experimental animals were sacrificed 3, 7, 14 days after replantation by heart infusion. The maxillae were removed, fixed, demineralized, dehydrated, infiltrated and embedded with JB-4 mixture. For light microscopic observation, 5 micron sections were cut and stained with toluidine blue. The results of this study were as follows : 1. After experimental 3 days, all groups were observed dead space between periodontum and root. 2. After experimental 7 days, group 1 and group 3 were observed filling periodontal fibers between alveolar bone and root but group 2 were not. 3. After experimental 7 days, group 3 were observed appearance of attached cementoblast like cell on root surface. Group 1 were observed regular arrangement of fibroblasts and collagen fibers at ${\times}400$ observation. 4. After experimental 14 days, all group were observed filling periodontal fibers between alveolar bone and root. Group 1 were observed normal arrangement of periodontal fibers. Group 3 were observed less abnormal arrangement of periodontal fibers. Group 2 were not observed functional normal arrangement of periodontal fibers. 5. After experimental 14 days, group 2 and 3 were observed several root resorption and irregular root surface but group 1 were not. These results suggest that the rh-BMP-4 can stimulate cementogenesis and enhance to attach collagen fibers.

• KIPS Transactions on Computer and Communication Systems
• /
• v.3 no.10
• /
• pp.383-392
• /
• 2014

The research for coatings is one of the most popular and active research in the polymer industry. For the coatings, electronics industry, medical and optical fields are growing more important. In particular, the trend is the increasing of the technical requirements for the performance and accuracy of the coatings by the development of automotive and electronic parts. In addition, the industry has a need of more intelligent and automated system in the industry is increasing by introduction of the IoT and big data analysis based on the environmental information and the context information. In this paper, we propose an optimization model for the design of experiments based coating formulation data objects using the Internet technologies and big data analytics. In this paper, the coating formulation was calculated based on the best data analysis is based on the experimental design, modify the operator with respect to the error caused based on the coating formulation used in the actual production site data and the corrected result data. Further optimization model to correct the reference value by leveraging big data analysis and Internet of things technology only existing coating formulation is applied as the reference data using a manufacturing environment and context information retrieval in color and quality, the most important factor in maintaining and was derived. Based on data obtained from an experiment and analysis is improving the accuracy of the combination data and making it possible to give a LOT shorter working hours per data. Also the data shortens the production time due to the reduction in the delivery time per treatment and It can contribute to cost reduction or the like defect rate reduced. Further, it is possible to obtain a standard data in the manufacturing process for the various models.

• The Journal of Art Theory & Practice
• /
• no.5
• /
• pp.7-24
• /
• 2007

The subject is connected with a structure named "The Symbolic" to Lacan, but he denied that the subject is explained simply as a fruit of language and "Other". From his point of view, passing through Subject, De-formation and Crack over it is designated as foundation of generation and creation rather than our destined defect. It should not be understood that subject of "The Real" is a concept of the subject free itself from restraint of "The Symbolic". However, this does not mean he asserts "Subject" is something incapable of being controlled by the unknown power. The problem is that this autonomous existence meets inside of it with something "more than one's own self" by "circulating around itself" like a permanent star. This is the indication of a "stranger in the middle of my privacy", or "extimit$\'{e}$", a coined-word by Lacan. Perhaps "Subject" is nothing more than the name of distance of object which is "too hot" to come close, and of this circulating movement. It's because of this object that the real subject stands against generalization and the subject can't be restored to any place in symbolic order-even though it is empty. The part which is told from Lacan's structural theory, that is to say, an importance to Lacan is that his Subject theory is not suggested or denied as a manual structure. On the contrary, it is a study of the relationship between the settled symbol that included in "real subject which is a unconscious one" and the symbolic subject hold- that is a metaphysical subject in general meaning. In Lacan's enlarged concept of subject beyond symbolic reality, it is noticeable that it gives justifiability to the union of a medium of different nature in artistic expression. We can recognize that the unconscious world is a living space which enables it to be a "condition of human being", not something dark under the surface of water through Magritte's(Rene Magritte, 1898~1967) surrealistic works. In other words, Magritte's art secures a core dimension of human nature through a mysterious gap of conscious and settled space. Magritte's drawings often evokes strange and unsettling feelings in people who view his paintings. This is because routine objects are found in "unsuitable" places from which we usually find them in our everyday lives. "Reality" in Magritte's paintings makes it aware that it is a strained field of concealment and disclosure basically between truths, and we can learn that his behavior to overturn to paint in-visible things is finally an effort to restore the "real subject" to the viewer's reality. In other words, such reversion arouses a nostalgic desire for the objects existing in their original appearance as they are - natural condition that our gaze had not been distorted yet by anamorphic stains. - and the state when we are conscious of them normally. Such desire offers an opportunity for us to get out of mental depression rather than operates to us as an abnormal crack. It's a successive process of effort to search for lost subject and Paradise Lost facing up to reality of subject human that is to be a subject of world and life are ousted from their place by structure and authority of culture.

• Korean Journal of Construction Engineering and Management
• /
• v.21 no.4
• /
• pp.21-29
• /
• 2020

This study analyzed problems of operating performance bond for public works and derived some suggestions for improvement. The Contract Law for Government Owner requires to submit performance bond which guarantees performing the construction contractor pays back compensation money when the obligation is not executed. Currently, first bid eligibility for participation is exactly required for executing company of performance bond obligation, not considering volume, technical level, and special type of remaining works. In collaboration contract, if guarantee accident occurs, it is obliged for remaining collaboration contractors to be qualified to fulfill the whole contract. This study proposes following improvement plan to solve problems of current performance bone in public works. Firstly, qualification criteria must be deregulated exceptionally for selecting proper contractor, which executing performance bond obligation, considering progress and characteristics of remaining works. Secondly, In collaboration contract, the prerequisite of remaining contractors' should be deregulated as 'implementation requirement of the remaining works'from'implementation requirement of the whole work'. Finally, defect responsibility should be included in liabilities of performance bond by specifying that owner or guarantee agency bear them.