• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.264-264
• /
• 2010

Single-walled carbon nanotubes (SWCNTs) were grown on a Si wafer by using thermal chemical vapor deposition (t-CVD). We investigated the effect of the catalyst deposition rate on the types of CNTs grown on the substrate. In general, smaller islands of catalyst occur by agglomeration of a catalyst layer upon annealing as the catalyst layer becomes thinner, which results in the growth of CNTs with smaller diameters. For the same thickness of catalyst, a slower deposition rate will cause a more uniformly thin catalyst layer, which will be agglomerated during annealing, producing smaller catalyst islands. Thus, we can expect that the smaller-diameter CNTs will grow on the catalyst deposited with a lower rate even for the same thickness of catalyst. The 0.5-nm-thick Fe served as a catalyst, underneath which Al was coated as a catalyst support as well as a diffusion barrier on the Si substrate. The catalyst layers were. coated by using thermal evaporation. The deposition rates of the Al and Fe layers varied to be 90, 180 sec/nm and 70, 140 sec/nm, respectively. We prepared the four different combinations of the deposition rates of the AI and Fe layers. CNTs were synthesized for 10 min by flowing 60 sccm of Ar and 60 sccm of $H_2$ as a carrier gas and 20 sccm of $C_2H_2$ as a feedstock at 95 torr and $810^{\circ}C$. The substrates were subject to annealing for 20 sec for every case to form small catalyst islands prior to CNT growth. As-grown CNTs were characterized by using field emission scanning electron microscopy, high resolution transmission electron microscopy, Raman spectroscopy, UV-Vis NIR spectroscopy, and atomic force microscopy. The fast deposition of both the Al and Fe layers gave rise to the growth of thin multiwalled CNTs with the height of ${\sim}680\;{\mu}m$ for 10 min while the slow deposition caused the growth of ${\sim}800\;{\mu}m$ high SWCNTs. Several radial breathing mode (RBM) peaks in the Raman spectra were observed at the Raman shifts of $113.3{\sim}281.3\;cm^{-1}$, implying the presence of SWCNTs (or double-walled CNTs) with the tube diameters 2.07~0.83 nm. The Raman spectra of the as-grown SWCNTs showed very low G/D peak intensity ratios, indicating their low defect concentrations.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.50-50
• /
• 2008

ZnO has been extensively studied for optoelectronic applications such as blue and ultraviolet (UV) light emitters and detectors, because it has a wide band gap (3.37 eV) anda large exciton binding energy of ~60 meV over GaN (~26 meV). However, the fabrication of the light emitting devices using ZnO homojunctions is suffered from the lack of reproducibility of the p-type ZnO with high hall concentration and mobility. Thus, the ZnO-based p-n heterojunction light emitting diode (LED) using p-Si and p-GaN would be expected to exhibit stable device performance compared to the homojunction LED. The n-ZnO/p-GaN heterostructure is a good candidate for ZnO-based heterojunction LEDs because of their similar physical properties and the reproducibleavailability of p-type GaN. Especially, the reduced lattice mismatch (~1.8 %) and similar crystal structure result in the advantage of acquiring high performance LED devices with low defect density. However, the electroluminescence (EL) of the device using n-ZnO/p-GaN heterojunctions shows the blue and greenish emissions, which are attributed to the emission from the p-GaN and deep-level defects. In this work, the n-ZnO:Ga/p-GaN:Mg heterojunction light emitting diodes (LEDs) were fabricated at different growth temperatures and carrier concentrations in the n-type region. The effects of the growth temperature and carrier concentration on the electrical and emission properties were investigated. The I-V and the EL results showed that the device performance of the heterostructure LEDs, such as turn-on voltage and true ultraviolet emission, developed through the insertion of a thin intrinsic layer between n-ZnO:Ga and p-GaN:Mg. This observation was attributed to a lowering of the energy barriers for the supply of electrons and holes into intrinsic ZnO, and recombination in the intrinsic ZnO with the absence of deep level emission.

• Journal of the Korea Concrete Institute
• /
• v.17 no.3 s.87
• /
• pp.329-334
• /
• 2005

The use of Polymer Concrete (PC) is growing very rapidly in many structural and construction applications such as box culverts, hazardous waste containers, trench lines, floor drains and the repair and overlay of damaged cement concrete surfaces in pavements, bridges, etc. However, PC has a defect economically because resin which be used for binder is expensive. Therefore the latest research is being progressed to replace existing resin with new resin which can reduce the high cost. Here, Polymer concrete using the recycled PET(polyethylene terephthalate) has some merits such as decrease of environmental destruction, decrease of environmental pollution and development of new construction materials. The variables of this study are amount of resin, curing condition and maximum size of coarse aggregate to find out mechanic properties of this. Stress-strain curve was obtained using MTS equipment by strain control. The results indicated that modulus of elasticity was increased gradually in an ascending branch of curve, as an increase of resin content. Compressive strength was the highest for resin content of $13\%$. And Compressive strength was increased as maximum size of coarse aggregate increases. The strain at maximum stress increases with an increase of resin content and size of coarse aggregate. For the descending branch of stress-strain curve the brittle fracture was decreased when it was cured at the room temperature compared to high temperature.

• Journal of the Korea Concrete Institute
• /
• v.17 no.3 s.87
• /
• pp.455-464
• /
• 2005

Today the application of antiwashout underwater concrete to the construction sites is increasing steadily, while its reliability is in issue. Particularly, antiwashout underwater concrete is known to have very weak durability on frost attack, and hence Japan society of civil engineers(JSCE) regulated that not to use of antiwashout underwater concrete where the freezing and thawing is suspected. This study aims the improvement of the freezing and thawing resistance for antiwashout underwater concrete. From the results of fundamental test, FA20 and SG50 showed good performance in fluidity and long term compressive strength than control concrete. Meanwhile, MK10 marked the highest compressive strength through the whole curing age but a defect on fluidity was discovered. The results from the repeated freezing and thawing test show that the large volumes of air entrapped by cellulose based antiwashout underwater admixture gave bad effects to frost durability and hence not much benefits were confirmed from the use of mineral admixtures. However there were some increasing effects on frost durability of MK10 and SG50 by securing $6{\pm}0.5\%$ of entraining air. In the meantime, there was a increasing tendency of frost durability by increasing blame's fineness of ground granulated blast furnace slag.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.6
• /
• pp.25-31
• /
• 2004

In this paper, we introduce kinetic Monte Carlo (kMC) methods for simulating diffusion process in nano-scale device fabrication. At first, we review kMC theory and backgrounds and give a simple point defect diffusion process modeling in thermal annealing after ion (electron) implantation into Si crystalline substrate to help understand kinetic Monte Carlo methods. kMC is a kind of Monte Carlo but can simulate time evolution of diffusion process through Poisson probabilistic process. In kMC diffusion process, instead of. solving differential reaction-diffusion equations via conventional finite difference or element methods, it is based on a series of chemical reaction (between atoms and/or defects) or diffusion events according to event rates of all possible events. Every event has its own event rate and time evolution of semiconductor diffusion process is directly simulated. Those event rates can be derived either directly from molecular dynamics (MD) or first-principles (ab-initio) calculations, or from experimental data.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.29 no.4
• /
• pp.219-225
• /
• 2003

Purpose: Platelet Rich Plasma(PRP) application is increasing with sinus inlay bone graft, but there is few research with radiographic ananlysis on effect of PRP in maxillary sinus. The author investigated the amount of bony changes of maxillary sinus for dental implantation among the patients with maxillary inlay graft. Materials and Methods: With 10 patients who were treated with sinus inlay autologous bone grafting combined with PRP technique, and with 5 patients who were treated with sinus inlay grafting only without PRP, the panoramic radiographys which were taken at preoperation, immediate postoperation, 3months postoperation, and 4 months postoperation(a month after dental implantation)periods were analysed. The films had been scanned, and then proceeded throughout image analysis system. The bone density of maxillary grafted sites was compared with adjacent tooth enamel density and remeasured according to density luminosity of each film. The density changes on PRP group and bone graft only group were analysed with non-parameteric statistics method. Results: In PRP combined patients group, bone density on postoperation periods was increased totally. The remarkable enhanced change of bone density was observed on 3 months postoperation period, thereafter the increasing rate was slightly reduced. In only bone graft patients group, bone density on postoperation periods was also increased compared with preoperation period, but the bone density of 4 months postoperation period was decreased compared with 3 months postoperation period. The amount of bone density on PRP group was significantly changed according to periods in contrast to bone graft only group. Conclusion: The bone density on PRP group was remarkably increased at 3 months postoperation compared to bone graft only group and it was seemed to be associated with more new bone formation, less grafted bone resorption at bone grafted sites with PRP.

• The Journal of Korean Academy of Prosthodontics
• /
• v.39 no.6
• /
• pp.659-681
• /
• 2001

Platelet-rich plasma(PRP) has been known to increase the rate and degree of bone formation by virtue of growth factors in concentrated platelets. Although its great healing effect on bone defect or pre-implantation site preparation in conjunction with bone substitute has been reported, the effect associated with implant is unknown. The purpose of this study was to investigate the effect of PRP on rapid osseointegration of endosseous dental implants in the rabbit tibiae. Twenty two adult female New Zealand white rabbits, weighing approximately 2.7-3.3kg, were used for this study. Twelve of the 22 animals were used for histomorphometric analysis and ten of the 22 were for removal torque test. Each animal received two implants in each tibia (two treated with PRP and two as control) and was given fluorochrome intramuscularly. For histomorphometric analysis, rabbits were divided into four groups according to the healing period. At 1 week, 2 weeks, 4 weeks and 8 weeks postoperatively, each three animals were sacrificed serially and the amount and rate of bone formation around dental implant were examined on the undecalcified sections under fluorescent microscope, polarized microscope and light microscope connected to a personal computer equipped with image analysis system. For removal torque test, rabbits were divided into two groups and removal torque tests were performed at 4 weeks, 10 weeks after implant placement. In total, 88 screw shaped, commercially pure titanium implants (Neoplant, Neobiotech, Seoul, Korea) were used in this study. Labeling pattern reflected differences of two groups in bone formation rate at each period. Histomorphometrically, PRP group showed significantly higher bone volume within threads compared to control group at 2 weeks ($70.30{\pm}4.96%$ vs. $50.68{\pm}6.33%$; P < .01) and 4 weeks ($82.59{\pm}5.94%$ vs. $72.94{\pm}4.57%$; P < .05 ). PRP group at 1, 2 and 4 weeks revealed similar degree of bone volume formation comparable to control group at 2, 4 and 8 weeks, respectively. On the other hand, while PRP group showed higher bone-implant contact ($47.37{\pm}8.09%$) than control group ($33.16{\pm}13.47%$) at 2 weeks, there were no significant differences between PRP group and control group for any experimental period. Removal torque values also showed no significant differences between PRP group and control group at any experimental period (P > .05). These findings imply that PRP could induce rapid, more bone formation around implant during early healing period and get faster secondary stability for reducing healing period, though it has not induced bone maturation enough to resist functional loading.

• Journal of Periodontal and Implant Science
• /
• v.26 no.4
• /
• pp.907-931
• /
• 1996

The purpose of this study was to study of the effects of the bioglass and the natural coral on healing process of the alveolar bone defects. Three adult dogs aged 1 to 2 years were used in this study. Experimental alveolar bone defects were created surgically with surgical bur and bone chisel at the furcation area of the buccal surface of the right and left mandibular 3rd, 4th premolars. Twelve experimental alveolar bone defects were devided into four groups according to the type of graft materials. The groups were as follows : 1. flap operation with root planing & curettage(Negative control group) 2. flap operation with autogenous bone(Positive control group) 3. flap operation with bioglass(BG group) 4. flap operation with natural coral(NC group) At 2, 4, and 8 weeks, the dogs were serially sacrificed and specimens were prepared with Hematoxylin-Eosin stain for light microscopic evaluation. The results of this study were as follows : 1. The defect areas were filled with granulation tissue at two weeks in negative control group. But in other groups, the appearance of connective tissues around graft materials were formed more densely and the response of inflammation by graft materials itself was not found. 2. In every control and experimental groups at two weeks, there was seen the accumulation of the formation of new bone trabeculae at the bottom of defects and gradually expanded toward the graft materials and in autogenous group there was slightly seen the formation of new cementum. 3. There was seen the erosion of central portion of bioglass particles at two weeks in BG group, and the erosion of the central portion was developed more progressively and was filled with bone-like tissues at eight weeks. 4. The natural coral particles were encapsulated by densely connective tissues and seen the formation of new bone tissues at four weeks and developed more new bone and cementum formation at eight weeks. From the results of this study, the bioglass and the natural coral may be biocompatible and have a weak adverse reaction to the periodontal tissues.

• Journal of Periodontal and Implant Science
• /
• v.25 no.3
• /
• pp.478-486
• /
• 1995

Periodontal therapy for treatment of periodontitis involves the elimination of bacterial plaque and elimination of the anatomic defects by regenerative procedure. The purpose of this study was to evaluate on the biological effect of magnolia and Ginkgo biloba extract to the antimicrobial, antiinflammatory and cellular activity. Antimicrobial assay was performed with the diffusion method of the extract by measuring of growth inhibitory zone of B. cereus from blood agar plate. Effect of the extract to cellular activity of gingival fibroblast were examined using MTT method and measured the result with optical density on 570nm by ELISA reader. Inhibitory effects of $PGE_2$ production from gingival fibroblast was performed with the addition of $IL-l{\beta}$ and the extract to the well and examined to the product of $PGE_2$ from cell by ELISA reader. In vivo anti-inflammatory effect was performed with injection examined with clinically and histologically for their extent of mecrosis and inflammation. Antimicrobial activity of Magnolia extract showed significantly higher activity than that of control. However, GBE did not showed significant activity to compare with control, and mixture of Magnolia and GBE extract showed significantly higher activity than that of control. The effect of cellular activity to gingival fibroblast showed no significant differences of between control and Magnolia extract. However, GBE showed significantly higher rate of cellular activity to compare with control and even to PDGF-BB, and also showed same degree of cellular activity even though mixed with Magnolia extract. The inhibitory effect of $PGE_2$ production showed significantly reduction of $PGE_2$ production to compare with control, but its inhibitory effect was not much strong to compare with Indomethacin. In vivo, antiinflammatory effect of Magnolia extract to P. gingivalis injection of Hamster buccal check showed significantly reduction of inflammatory cell infiltration and tissue necrosis, but GBE showed no effect on the inhibition of inflammatory process. These results suggested that Magnolia and GBE extract possessed different kind of biological activity and also can be compensated on their activity with each other for elimination of bacterial plaque and anatonical defect.

• Journal of Periodontal and Implant Science
• /
• v.25 no.3
• /
• pp.603-613
• /
• 1995

The purpose of this investigation was to evaluate on the biodegradability, biocompatibility and tissue regenerative capacity of synthetic bioabsorbable membranes in beagle dogs. For animal study, 9 adult beagle dogs were used to examination, on the surgical implantation of membranes and histological analysis. In each animal, the 3rd and 4th premolars of the both sides of the mandible were selected as test teeth. Two types of bioresorbable membranes including "Guidor membrane", "S-membranes" were used to examining for biological activity, and also Gore-tex membranes was used for positive control. Surgically created defects were made in 2 premolars of both sides of the mandible at $3{\times}4mm^2$ in size and tested membranes were implanted in the defected area. A plaque control regimen was instituted with daily tooth brushing with a 0.1% chlorhexidine digluconate during experimental periods. All the experimental animals were sacrificed after 2, 4, and 8 weeks from surgery and undecalcified slides were prepared using the "sawing and grinding" technique described by Donath and Breuner". In biodegradability, all the membranes were started their biodegradation from two weeks after implantation and gradually demolished of their frame morphology from eight weeks. However, demolition of membranes in 8 weeks after implantation was highest in Guidor membranes and followed by S-membranes. Biocompatibilityof two kinds of biodegradable membranes including Guidor and S-mambrane were shown to be well tolerated to the surrounding tissue, and were minimal accumulation of inflammatory cell infiltration around the implanted membranes to compare with Gore-tex membrane. Regeneration of defected alveolar bone was initiated from two weeks of membrane implantation and new bone formation was gradually increased from that time. However, pattern of new bone formation on the defected areas of two kinds of biodegrable membranes was almost similar and quite competitive comparing with Gore-tex membrane. These results implicate that bioresorbable membranes should be highly useful tool for guided tissue regeneration of periodontal defects.