• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.11
• /
• pp.967-976
• /
• 2016

This paper presents a 3D carrier-smoothed GNSS/DR (Global Navigation Satellite System/Dead Reckoning) integrated system for precise ground-vehicle trajectory estimation. For precise DR navigation on sloping roads, the AHRS (Attitude Heading Reference System) methodology is employed. By combining the integrated carrier phase of GNSS and DR sensor measurements, a vehicle trajectory with an accuracy of less than 20cm is obtained even when cycle slip or change of visibility occur. In order to supplement the weak GNSS environment with DR successfully, the DR sensor is precisely compensated for using GNSS Doppler measurements when GNSS visibility is good. By integrating a multi-GNSS receiver with low-cost IMU, a precise 3D navigation system for land vehicles is proposed in this paper. For real-time implementation, a decoupled Kalman filter is employed in the integrated system. Through field experiments, the performance of the proposed system is verified in various road environments, including sloping roads, good-visibility areas, high multi-path areas, and under-ground parking areas.

• Proceedings of the KIEE Conference
• /
• 2003.07d
• /
• pp.2230-2232
• /
• 2003

One of the important problems in a control system design is the requirement that the system should have adequate relative stability. In this paper, We proposed a tuning algorithm PI controller for first order plus dead time system. It is determined the domain of the PI control parameters by Routh - Hurwitz criterion, and we tune parameters of the PI controller using genetic algorithm. A numerical example is also given to illustrate the method.

• Journal of Power Electronics
• /
• v.11 no.1
• /
• pp.64-73
• /
• 2011

The stability of PWM rectifiers with a deadbeat current controller is seriously influenced by computation time delays and low-pass filters inserted into the current-sampling circuit. Predictive current control is often adopted to solve this problem. However, grid current predictive precision is affected by many factors such as grid voltage estimated errors, plant model mismatches, dead time and so on. In addition, the predictive current error aggravates the grid current distortion. To improve the grid current predictive precision, an improved deadbeat current controller with a repetitive-control-based observer to predict the grid current is proposed in this paper. The design principle of the proposed observer is given and its stability is discussed. The predictive performance of the observer is also analyzed in the frequency domain. It is shown that the grid predictive error can be decreased with the proposed method in the related bode diagrams. Experimental results show that the proposed method can minimize the current predictive error, improve the current loop robustness and reduce the grid current THD of PWM rectifiers.

• Journal of Energy Engineering
• /
• v.5 no.1
• /
• pp.28-33
• /
• 1996

This study was carried out find out the appropriate tuning method of PID controller for a package type gas engine cogeneration system in terms of stabilizing the engine coolant temperature and system heat balance. In order to acquire the proper parameters of the controller, a system transfer function was set as a first order plus dead time model and thereafter model parameters were determined by using several tuning methods. And, with determined values of parameters and the system transfer functions, optimal turning method was selected by simulating the process using MATLAB. From the experimental results, it was found that obtained PID gains made the system stable in various operating conditions.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.5
• /
• pp.379-386
• /
• 2009

This paper investigates the operation of ITER(International Thermonuclear Experimental Reactor) Vertical Stabilization(VS) converter with circulating current. The VS converter has two subunits in parallel. The subunit is composed two back-to-back 12 pulse thyristor converter in series. The circulating current free technique can not always maintain the closed path for the load current because of a dead time zone of the converter operation at the region of the load current inversion. The complex circulation current technique for the load current inversion with VS converter can achieve the fast response and always maintain the closed path for the load curret. The paper proposes the new circulating current algorithm for the load current inversion of ITER VS converter and proves the performance of the circulating current technique with PSIM simulation study.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.6
• /
• pp.569-575
• /
• 2013

This paper proposes a method for PDR (Pedestrian Dead-Reckoning) using a low cost IMU. Generally, GPS has been widely used for localization of pedestrians. However, GPS is disabled in the indoor environment such as in buildings. To solve this problem, this research suggests the PDR scheme with an IMU attached to the pedestrian's waist. However, despite the fact many methods have been proposed to estimate the pedestrian's position, but their results are not sufficient. One of the most important factors to improve performance is, a new calibration method that has been proposed to obtain the reliable sensor data. In addition to this calibration, the PDR method is also proposed to detect steps, where estimation schemes of step length, attitude, and heading angles are developed. Peak and zero crossings are detected to count the steps from 3-axis acceleration values. For the estimation of step length, a nonlinear step model is adopted to take advantage of using one parameter. Complementary filter and zero angular velocity are utilized to estimate the attitude of the IMU module and to minimize the heading angle drift. To verify the effectiveness of this scheme, a real-time system is implemented and demonstrated. Experimental results show an accuracy of below 1% and below 3% in distance and position errors, respectively, which can be achievable using a high cost IMU.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.5
• /
• pp.703-708
• /
• 2011

In this paper, most of the church except for a large church has accommodated many audience to install a balcony floor in a small space. therefore, dead zone and dislocated sound image localization is made due to this under-balcony seats. This paper propose that the problems of dead zone and dislocated sound image localization could be solved using computer simulation in the view of practical side. The economical computer simulation tool, Mapp online that can be found easily was used to the specified church. Installation a sub speaker for dead zone and -10 dB power control of the sub speaker to main speaker power for dislocated sound image localization was proposed. Computer simulation result shows that the value of definition for area was improved from "Normal" to "Very Good" which means about 52% improvement.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.787-792
• /
• 1991

This paper proposes a steering control algorithm for non-holonomic mobile robots. The steering control algorithm is essential to navigate autonomous vehicles which employ comination of the dead reckoning and absolute sensor system such as a machine vison for detecting landmarks in order to estimate the current location of the mobile robot. The proposed algorithm is based on the minimum time BANG-BANG controller and curvature-continuity curve design method. In the BANG-BANG control scheme we introduce velocity/acceleration limiter to avoid any slippage of driving wheels. The proposed scheme is robot-independent and hence can be applied to various kinds of mobile robot or vehicles. To show the effectness of the proposed control algorithm, a series of computer simulations were conducted for two-wheel driven mobile robot.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.61 no.1
• /
• pp.47-54
• /
• 2012

This paper presents implementation of SVPWM technique for three phase Voltage Source Inverter using FPGA. Software-based vector-control calculations much this drawback, in order to improve the hardware-vector-control tries. Without the need for additional software, vector control algorithm is designed to be modular SOPC, and DSP will reduce most of the operations. In this paper, the SVPWM that using HDL for the AC motor vector control algorithm level, and the dead time part and the speed control in order to controled a speed detector and designed in the form of modules. Then ALTERA corporation Cyclone III series EP3C16F484 can be verified by implemented.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.3
• /
• pp.320-329
• /
• 2012

The Load Tap Changing (LTC) transformer and Shunt Capacitor (SC) bank are major devices for voltage and reactive power control in a distribution substation. Thus, the coordination operation of a LTC transformer and a SC bank is required to achieve better voltage and reactive power compensation at a distribution substation in the same time. This paper proposes coordinate control method of LTC transformer and SC bank to achieve better voltage and reactive power compensation and operation times of these two devices in the same time. The mathematical formulations of the proposed coordinate control method are introduced. Sample case studies are shown to verify the effectiveness of the proposed coordinate control method.