• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05c
• /
• pp.201-206
• /
• 1996

건식가공(Dry Process)이 사용전,후 DUPIC 핵연료의 붕괴열(Decay Heat), Hazard Index, 조사선량률(Dose Rate) 등에 미치는 영향을 계산하고, 그 원인을 분석하였다. DUPIC 사용방안으로 표준 연소도(35,000 MWD/MTU)의 경우와 장주기 연소도(50,000 MWD/MTU)의 경우를 고려하여 계산하였으며, DUPIC핵연료는 20년 냉각후 가공하는 것을 기준으로 하였다. 또한 DUPIC핵연료 장전시 고려할 수 있도록 사용전 DUPIC 핵연료에 대한 계산을 핵연료 집합체(Bundle) 단위로 하였다. 조사선량과 붕괴열은 건식가공에 상당히 민감한 반응을 보였고 이는 주로 Cs의 제기에 의한 것이다.

• Journal of Radiation Protection and Research
• /
• v.21 no.1
• /
• pp.27-39
• /
• 1996

The change in spent fuel characteristics by DUPIC fuel cycle(burnup of spent PWR fuel again in CANDU) is examined with time elapse since discharge. Major characteristics examined include isotopic concentration, radioactivity, decay heat radiotoxicity and radiation source-term of spent fuel material, which is existing in a type of spent PWR and DUPIC fuel. Behaviors of major nuclides contributing to such changes are also analyzed in terms of radionuclide concentration. From the analysis, the change in radionuclide concentration by DUPIC shows approximately 2% decrease in actinides concentration and 20% increase in fission products concentration. Radioactivity and decay heat of spent DUPIC fuel does not depend upon radionuclides concentrations, which is a unique in sence of general characteristics of spent fuel. In terms of gamma spectrum, spent DUPIC fuel shows lower values than that of spent PWR fuel by 40 to 50% in the range of $0.01{\sim}0.575$ MeV but much higher over 3.5MeV. Neutron Intensities of both spent fuels are mainly determined by $({\alpha},\;n)$ reaction and spontaneous fission reaction of actinides. Of them, especially, the spontaneous fission reaction Is a major neutron source-term, which causes that neutron intensities of spent DUPIC fuel $having{\sim}3.3$ times higher Cm-244 concentration are ${\sim}4$ times higher than that of spent PWR fuel.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2005.05a
• /
• pp.517-518
• /
• 2005

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05b
• /
• pp.715-720
• /
• 1995

DUPIC 핵연료의 제작 조건, 특히 소결 조건에서 필요한 O/M값에 따른 산소포텐샬을 점결함모형을 이용하여 구하였다. 산소포텐샬 값은 순수 우라니아에서보다 크게 나타났고 주요 점결함 형태의 변화로 온도에 따라 엔트로피 값의 변화가 보였다. 연소중 DUPIC핵연료의 산소포텐샬 변화는 핵연료를 닫힌 계로 보고 물질 보존 및 평형법칙을 기초로 하여 구하였다. 산소포텐샬은 초기에 급격히 증가하지만 곧 일정한 값에서 매우 완만히 증가하게 된다. O/M값도 거의 변화가 없는데, 이는 Mo의 완충작용 때문이다. 따라서 초기 Mo의 화학적 형태- 금속 또는 산화물-가 DUPIC핵연료 O/M값 변화에 큰 영향을 미칠 것으로 예측되며 DUPIC핵연료 제작시 소결 조건에 유의할 필요가 있다.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.2 no.2
• /
• pp.125-133
• /
• 2004

Fission products of DUPIC (Direct Use of Spent PWR Fuel in CANDU Reactors) fuel, irradiated in HANARO research reactor with 61 ㎾/m of maximum linear power and 1,770 ㎿d/tU of average burn-up, was characterized by EPMA(Electron Probe Micro Analyzer). In order to find accurate characterization, the analysis results by EPMA of fresh simulated DUPIC fuel containing fission products as chemicals were compared with that of wet chemical analysis. The metallic precipitates observed at the center of the fresh simulated DUPIC fuel were about 1 $\mu\textrm{m}$ in size and their major components by EPMA were Mo-53.89 at.%, Ru-37.40 at.%, and Pd+Rh-8.71 at.%. Established procedure through the fresh simulated DUPIC fuel was applied to the irradiated DUPIC fuel. Observed size of metallic precipitates were 2∼2.5 $\mu\textrm{m}$ and their compositions were Mo-47.34 at.%, Ru-46 at.%, and Pd+Rh-6.65 at.%. What are uncommon things for this experiment, special treatment for improving the conductivity was attempted to the specimen and the conditions of exact irradiation of electron beam to small metallic precipitate were suggested.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2004.02a
• /
• pp.170-181
• /
• 2004

DUPIC powder and pellets were successfully fabricated in accordance with the quality assurance program described in the Quality Assurance Manual for DUPIC fuel fabrication, which was developed on the basis of the CAN3-Z299.2-85 standard. This manual describes the quality management system applicable to the activities performed for DUPIC fuel fabrication. It covers the work processes, policies and procedures used for planning, executing, and verifying the work carried out for DUPIC fuel fabrication. It is important that a Quality Program is in place before the fabrication of the fuel for irradiation testing. In order to qualify the DUPIC pellet manufacturing processes, 3 series of experiments for the pre-qualification and 3 series for the qualification were performed. In these experiments, the optimum process conditions were established. Then, under the control of the QA program, 8 series of production runs were performed to make the qualified DUPIC pellets in a batch size of 1 kg. In these production runs, DUPIC fuel pellets satisfying the standard CANDU fuel pellet specifications could be successfully produced.

• Journal of Radiation Protection and Research
• /
• v.21 no.2
• /
• pp.117-124
• /
• 1996

Source intensities in terms of the exposure rates at 1m from the fresh and spent DUPIC fuels, made from standard and extended turnup PWR fuels, were analyzed. Two cases were studied based on the degree of elimination of removable elements. Homogeneous mixture model was applied to get the exposure rate. The exposure rate turned out to be very high and sensitive to Cs elimination during the dry process. About 90% of exposure can be reduced in the case of fresh DUPIC fuel made from 10-year cooled spent PWR fuels if Cs is fully removed during the dry process. The main radiation source in spent fuels is Cs-137. The dry storage of spent DUPIC fuel may need a longer wet storage period and require a further review.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.250-255
• /
• 1998

DUPIC 핵연료 개발에서는 소결체의 물성연구와 노내거동부터 연구를 시작하여 신 개념의 핵연료의 개발에 부합되는 조사시험 계획이 수립되어야 하기 때문에 DUPIC소결체의 물성 및 노내거동 연구를 캡슐을 이용하여 조사시험을 수행할 계획이다. 본 논문에서는 노외 시험 및 예비 특성화(Pre-Characterization)와 노내시험인 DUPIC 핵연료 소결체 시험 그리고 연료봉 조사시험에 필요한 항목들에 대하여 분석하였으며 DUPIC 소결체가 하나로 노심의 CT, IR2, IP9등에서 무계장 캡슐을 이용하여 조사될 경우의 출력을 평가 하였다. 또한 모의 핵연료와 DUPIC 핵연료 소결체의 조사시험을 위해 무계장 캡슐 (Capsule)에 대하여 연구 하였다.

• Journal of Welding and Joining
• /
• v.19 no.1
• /
• pp.88-94
• /
• 2001

DUPIC (Direct use of spent PWR fuel in CANDU reactors) nuclear fuel is a CANDU fuel fabricated remotely from spent PWR fuel materials in a hot cell. The soundness of the end closure welds of nuclear fuel elements is an important factor for the safety and performance of nuclear fuel. To evaluate the soundness of the end closure welds of DUPIC fuel element, a precise X-ray inspection system is developed using a micro-focus X-ray generator with an image intensifier and a real time camera system. The fuel elements made of Zircaloy-4 and stainless steel by an Nd:YAG laser welding and a TIG welding aye inspected by the developed inspection system. The soundness of the welds of the fuel elements was confirmed by the X-ray inspection process, and the irradiation test of DUPIC fuel elements has been successfully completed at the HANARO research reactor.

• Journal of Powder Materials
• /
• v.7 no.3
• /
• pp.123-130
• /
• 2000

The simulated DUPIC fuel provides a convenient way to investigate fuel properties and behaviours such as thermal conductivity, thermal expansion, fission gas release, leaching and so on. Several pellets simulating the composition and microstructure of the DUPIC fuel were fabricated from resintering powder through the OREOX process of the simulated spent fuel pellets, which were prepared from the mixture of stable forms of constituent nuclides. This study describes the powder treatment, OREOX, compaction and sintering to fabricate simulated DUPIC fuel using the simulated spent fuel. The homogeneity of additives in the powder was observed after attrition milling. The microstructure of the simulated spent fuel was in agreement with the previous studies. The densities and the grain size of simulated DUPIC fuel was pellets are higher than those of simulated spent fuel pellets. Small metallic precipitates and oxide precipitates were observed on matrix grain boundaries.