• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.6
• /
• pp.40-51
• /
• 2009

To analyze influences under open faults in switching devices of the PWM inverter and under the isolation between the inverter and motor terminal, a faulty model for the inverter-driven permanent magnet synchronous motor is presented. Even though the conventional dq motor model obtained through the transformation of phase voltage model is widely used to analyze and control AC motor, it can not be used under open faults in switching devices since the 3-phase balanced condition is no longer hold under the open fault and it is not easy to obtain motor input voltages in open phase from the pole voltage. To deal with this problem, a faulty model for an inverter-driven permanent magnet synchronous motor is derived by using the line voltage of motor according to switch open, which can be effectively used for performance evaluation of the diagnostic algorithm. The validity of the proposed faulty model is verified through comparative simulations and experiments using DSP TMS320F28335.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.3
• /
• pp.188-198
• /
• 2010

Recently, as the demand of the environmental-friendly energy storage system such as an electric double-layer condenser increases, that of the bidirectional charger/discharger for the systems also increases. However, when charging/discharging mode-change occurs, the charger/discharger employing a bi-directional DC-DC converter with a commercialized analog controller has a complex circuit scheme, and a poor transient response. On the other hand, if a single digital controller is used for the bi-directional mode, the system performances can be improved by application of an advanced power-processing algorithm. In the paper, an environmental-friendly power storage systems including an Electric Double Layer Capacitor(EDLC) banks were developed with a bi-directional buck-boost converter and a digital signal processor (TMS320F28335). A simulation test-bed was realized and tested by MATLAB Simulink, and the hardware experiment was performed which shows that the dynamic response was improved such as the simulation results.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.5
• /
• pp.94-105
• /
• 2010

To detect faults in an inverter-fed permanent magnet synchronous motor (PMSM) drive under the circumstance having faults in a stator winding and inverter switch, an on-line basis fault detecting scheme during operation is presented. The proposed scheme is achieved by monitoring the second-order harmonic component in q-axis current and the fault is detected by comparing these components with those in normal conditions. The linear interpolation method is employed to determine the harmonic data in normal operating conditions. As soon as the fault is detected, the operating mode is changed to identify a fault type using the phase current waveform. To verify the effectiveness of the proposed fault detecting scheme, a test motor to allow inter-turn short in the stator winding has been built. The entire control algorithm is implemented using DSP TMS320F28335. Without requiring an additional hardware, the fault can be effectively detected by the proposed scheme during operation so long as the steady-state condition is satisfied.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.441-442
• /
• 2015

This paper proposes a new single-phase seven-level grid-connected inverter. Operational principle with switching function are analyzed. A digital proportional-integral current-control algorithm was implemented in a TMS320F28335 DSP to keep the current injected into the grid sinusoidal. To verify the performance of the proposed inverter, PSIM simulation and experimental results are also shown in this paper.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.3
• /
• pp.146-152
• /
• 2012

To install a wind power generator, the survey on the wind environment resources must be conducted in advance. The survey on the wind environment resources is to collect and analyze data regarding the wind speed and direction on a data logger. The data logger consists of a sensor, signal processing circuit and storage device. According to the analysis of the stored data, the amount of power generation by the types of generators can be predicted and the most optimal generator including safety grade can be selected, and in case of installing a generator in the future, it can be utilized as basic data regarding supporting base and foundation construction method of survey points. Data logger was developed for a small wind power generator that is suitable for the international standard(IEC 61400) by using DSP-F28335 micro controller in this paper. It was developed to measure the wind speed of 1 [m/s]~17 [m/s], the wind direction of 0 [$^{\circ}$]~359 [$^{\circ}$], and temperature of -30 [$^{\circ}C$]~50 [$^{\circ}C$], and the comparative experiment with other companies' data loggers was conducted, and an error was measured to be less than ${\pm}0.1$ [m/s] for wind speed and less than +1 [$^{\circ}$] for wind direction.

• Journal of Power Electronics
• /
• v.16 no.6
• /
• pp.2306-2314
• /
• 2016

Design and implementation of a low cost grid-connected 5kVA solar photovoltaic (PV) system is proposed in this paper. Since the inverter is a major component of the PV system, the B4 inverter used in this paper reduces the total cost of the PV system. In order to eliminate the massive transformer, the PV system is connected to the grid through IGBT switches. In addition to injection of active power into the grid, the B4 inverter can compensate reactive power and reduce harmonics of the nonlinear loads. A TMS320F28335 DSP processor is used for effective control of the B4 inverter. Various features of this processor enable the implementation of the necessary control algorithms. As a first step, the PV system is simulated and evaluated in Matlab/Simulink. In the second step, hardware circuits are designed and implemented based on the simulation results. The operation of the PV system has been evaluated under balanced, unbalanced, linear and nonlinear loads which proves its accuracy and efficiency.

• Proceedings of the KIPE Conference
• /
• 2009.11a
• /
• pp.75-77
• /
• 2009

양방향 DC-DC컨버터는 일반적으로 아날로그방식이 사용되고 있다. 그러나 충 방전기로 사용하게 되면 모드전환 시 과도 응답특성이 좋지 않은 문제가 있다. 이에 대한 대안으로 디지털 제어기를 사용하게 되면 진보된 알고리즘들을 이용하여 시스템의 성능을 향상 시킬 수 있다. 본 본문에서는 전기이중층 콘덴서(EDLC)를 이용한 동적전압보상장치(DVR)의 양방향 충/방전 시스템을, Buck/Boost 양방향 컨버터를 이용하여 구현하고, DSP(TI사 TMS320F28335)를 이용한 디지털 제어기를 적용하였다. 모의실험 및 하드웨어를 구성하여 실험한 결과, 양방향 시스템의 과도응답특성 개선과 시스템 성능 향상을 보여준다.

• Proceedings of the KIPE Conference
• /
• 2017.11a
• /
• pp.55-56
• /
• 2017

본 논문에서는 향후 기후환경 변화에 따른 전력변환장치의 특성을 분석하기 위해 많은 소자들 중에서 전력용 스위치의 출력 특성을 분석하였다. 전력변환장치는 일반적으로 폐루프 제어를 함으로써 출력 특성의 변화를 보상해 주어 온도변화에 대한 스위치 자체의 특성을 관찰하기가 어렵다. 따라서 본 논문에서는 타이머 555IC, DSP320F28335를 이용하여 고정된 듀티를 출력할 수 있도록 회로를 구성하고, 온도변화를 주어 스위치의 출력 특성을 보고자 한다.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.527-528
• /
• 2015

최근 다양한 디지털기기에 따른 DC 부하의 증가와 함께 기존 배전망과 연계하여 운용할 수 있는 AC 그리드와 태양광과 연료전지 같은 DC 전원에 직접적으로 연계하여 운용하는 DC 그리드를 통합하는 AC/DC 마이크로그리드에 대한 연구가 진행되고 있다. 본 논문에서는 AC 그리드와 DC 그리드를 연계 제어하는 연계(interlinking) 컨버터의 제어기를 설계하고 성능을 검토하기 위해 TMS320F28335 DSP(Digital Signal Processor)와 실시간 디지털 시뮬레이터인 eMEGAsim으로 구성된 HILS(Hardware-in-the-Loop Simulation) 시스템을 구축하고 설계된 제어기의 성능을 테스트하였다.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1014-1015
• /
• 2015

본 논문은 MLCC (Multi-Layer Ceramic Capacitor) 시험용 전원 장치의 설계에 대해 기술 하였다. 개발된 전원 장치의 정격 출력 전압과 전류는 600V / 2A이며 경부하에서 중부하까지 200mV이하의 고 정밀도를 가진다. 전원 장치의 토플로지는 2-스위치 플라이백 컨버터를 인터리브시켜 고 전력/고 시스템 주파수가 가능하도록 구성했다. 출력 필터와 시스템 제어기를 설계하여 전압 리플과 노이즈를 감쇠시키고 시스템 안정도를 높였다. 특히 16bit AD변환기를 이용하여 제어 변수를 받아, DSP(TI사(社) TMS320F28335)로 정전압(CC) / 정전류(CV) 모드 제어를 보다 정밀하게 하였다. 최종적으로 시뮬레이션과 실험을 통해 고 정밀 전압의 전원 장치 설계의 타당성을 확인 하였다.