• Journal of Welding and Joining
• /
• v.30 no.6
• /
• pp.68-73
• /
• 2012

Nowadays, car manufacturers tried to improve automotive fuel efficiency, and applied many high strength steels such as AHSS or UHSS to car bodies. Therefore, the number of steel combinations for the resistance spot welding are dramatically increased and the need for weldability evaluation of these combinations are also required. In this study, we suggest the lobe curve using FEM simulations for DP780 steel with 1.0t, 1.4t. The lobe curves which could expressed weldablity and optimal welding condition were obtained according to 6 steel combinations. There were two combinations for same steel sheet which were DP780 1.0t, DP780 1.4t. Dissimilar steel sheet combination with different thickness was 1.0t and 1.4t of DP780. Different steel combinations were DP780 1.0t and SPRC440 1.0t, and DP780 1.0t and DP590 1.0t. Finally dissimilar combinations was and DP780 1.0t and DP590 1.4t. The trend of low boundary and high boundary variation of lobe curve were analyzed with a viewpoint of the contact resistance and the heat input.

• Journal of the Korean Society for Heat Treatment
• /
• v.37 no.6
• /
• pp.281-287
• /
• 2024

This study investigated the hardness and microstructure of dual-phase (DP780) steel as a function of temperature and examined the effect of tempering temperature on the microstructure and mechanical properties of DP steel. The aim was to explore the changes in mechanical properties that rely on heat treatment when processing high-strength steel, widely used in the automotive industry. The dual-phase microstructure, composed of ferrite and martensite phases, showed variations in phase fractions with tempering temperature. Specifically, the hardness decreased up to 600℃, then increased above 600℃, with the lowest hardness observed at 600℃. This is attributed to the recovery and martensite decomposition caused by low-temperature tempering, leading to a decrease in hardness. Above 600℃, the formation of new martensite resulted in increased hardness. Therefore, high-strength steel with a dual-phase microstructure like DP780 is significantly affected by the martensite fraction resulting from tempering during processing, which has a substantial impact on its mechanical properties.

• Transactions of Materials Processing
• /
• v.21 no.6
• /
• pp.384-388
• /
• 2012

Sheet metal forming processes induce residual stress in the final product due to plastic deformation. The residual stress leads to elastic recovery of the formed part called springback, which causes shape errors in the final product. This error is a serious issue, especially for high strength steels, which are widely used in auto-body structures. Therefore, the evaluation of the amount of springback becomes critical for high strength steels. This paper investigates the springback behavior of DP780 steel sheets after the U-bending process using the geometry of the standard U-shape tool from the NUMISHEET'93 benchmark problem. The amounts of springback were measured as a function of the intrusion direction, forming speed and blank holding force.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.11
• /
• pp.46-56
• /
• 2010

The present research works investigated into the low velocity impact characteristics of DP 780 high strength steel sheet with 1.7 mm in thickness subjected to free boundary condition using three-dimensional finite element analysis. Finite element analysis was carried out via ABAQUS explicit code. Hyper-elastic model and the damping factor were introduced to improve an accuracy of the FE analysis. An appropriate FE model was obtained via the comparison of the results of the FE analyses and those of the impact tests. The influence of the impact energy and nose diameter of the impact head on the force-deflection curves, impact time, absorption characteristics of the impact energy, deformation behaviours, and stress-strain distributions was quantitatively examined using the results of FE analysis. The results of the FE analysis showed that the absorption rate of impact energy lies in the range of the 70.7-77.5 %. In addition, it was noted that the absorption rate of impact energy decreases when the impact energy increases and the nose diameter of the impact head decreases. The local deformation of the impacted region was rapidly increased when the impact energy was larger than 76.2 J and the nose diameter was 20 mm. A critical impact energy, which occur the instability of the DP780, was estimated using the relationship between the plastic strain and the impact energy. Finally, characteristics of the plastic energy dissipation and the strain energy density were discussed.

• Journal of the Korean Society of Industry Convergence
• /
• v.20 no.1
• /
• pp.81-87
• /
• 2017

In order to reduce the weight of the blow motor case and to maintain the strength of the motor joint, the mechanical joining strength is to be predicted. The true stress - true strain curves for finite element analysis were obtained through tensile tests of HGI and DP 780 steel. The mechanical joining strength was predicted through an explicit finite element analysis and the accuracy of the predicted results was verified by actual sample test. The regression equation for predicting the mechanical joining strength to the thickness of the DP 780 steel was derived. The minimum thickness of DP 780(1.2mm), which is equivalent to the joining strength of HGI(2.6mm), was derived from the equation.

• Transactions of Materials Processing
• /
• v.17 no.3
• /
• pp.197-202
• /
• 2008

The control of springback is very important in sheet metal forming since springback affects the dimensional inaccuracy of product. The object of this study is to design the manufacturing process for the improvement of the performance of seat rail by DP780. The influence of process variables such as bend angle and pad force on the springback has been firstly investigated through the comparison between the results of FE-analysis and trial out for initial design based on designer's experience. The process variables of the initial design have been modified in order to improve the dimensional accuracy of seat rail from the prediction of springback by FE-analysis. It was shown from experiment that the improved design satisfied the required specifications such as the dimensional accuracy and the strength of seat rail.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.341-348
• /
• 2004

Recently deveoped HSS of POSCO and commerciallizing activities were introduced. 590DP, 590FB, 780TRIP. In this year, another three type of hot rolled AHSS will be developed and try to commerciallize with auto makers. 780FB, 780DP and 980CP. We have future plan to develope ultra high strength steels 980TR, 1170CP.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.3
• /
• pp.279-286
• /
• 2015

To achieve lightweight design, research & development of various lightweighting technologies such as hydroforming are underway worldwide. In the case of hydroforming, application of ultra high strength steel is essential for weight reduction of the car. However, considering common high-strength carbon steel, it is not suitable to the actual hydroformed parts since the lack of formability. DP steel offers an outstanding combination of strength and formability as a result of their microstructure. DP steel has high strength and good formability but it's difficult to secure stable quality of welding section because of softening of weld section and chemical composition. Therefore, most of companies use LASER welding when making high strength tube. Electric resistance welding is excellent production method for steel tube manufacturing considering the productivity. Optimum electric resistance welding technology is needed to be developed for application of high strength hydroformed parts using DP steel. This study is comprehensive research & development from electric resistance welding to actual formabililty evaluation.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.301-306
• /
• 2009

High strength steels are widely used for lightweight automobile parts and the control of springback is very important in sheet metal forming. The object of this study is to develop the forming process for stair type side sill made of high strength steel, DP780. Stair type side sill with local formed area and geometry change area can improve stiffness and design freedom but there are a few studies for forming process. The forming technology considered in this paper is form type process, which have many advantages for farming of high strength steel compared with draw type process. Finite element analysis is carried out to predict formability and springback. It is shown that angle calibration of die is essential for reducing springback, and local forming involving bead is effective to control springback also. The effectiveness of local forming and angle calibration is verified by experimental.

• Transactions of Materials Processing
• /
• v.18 no.8
• /
• pp.601-606
• /
• 2009

High strength steels are widely used for lightweight automobile parts and the control of springback is very important in sheet metal forming. The object of this study is to develop the forming process for stair type side sill made of high strength steel, DP780. Stair type side sill with local formed area and geometry change area can improve stiffness and design freedom but there are few studies for forming process. The forming technology considered in this paper is form type process, which has many advantages for forming of high strength steel compared with draw type process. Finite element analysis is carried out to predict formability and springback. It is shown that angle calibration of die is essential for reducing springback, and local forming involving bead is effective to control springback also. The effectiveness of local forming and angle calibration is verified by experimental.