• Journal of the Optical Society of Korea
• /
• v.1 no.2
• /
• pp.110-115
• /
• 1997

We report effcient cascaded Raman generation and signal amplification at 1.3.mu.m achieved in a ring resonator constructed solely from fiber components, i.e. fusion WDM couplers. Low-loss single-mode fiber with moderate $GeO_2$ content (18 mole %) is used as an active medium and pumped by a Nd:YAG laser at 1.064.mu.m. In a resonant cascaded geometry, this generates the third Stokes line at 1.24.mu.m, which acts as a pump for signal wavelength around 1.3.mu.m. A DFB laser operating at 1.315.mu.m is used to provide an input signal. An output signal powers up to 20 dBm (100 mW) with a 28 dB Raman gain are attained, where the Nd:YAG pump power is 3.4 W. It is also shown experimentally that it is important to use optical filters to suppress feedback from the resonator, permitting high Raman gain and good signal quality.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04a
• /
• pp.197-200
• /
• 2000

All-optical NOR logic device was realized by use of two pump signals with a single wavelength and a semiconductor optical amplifier(SOA). Specially, Mach-Zehnder(MZ) modulator was used for an external modulation of the pump signals. To obtain the sufficient gain saturation of the SOA, pump signals are amplified by an Er-doped fiber amplifier(EDFA) at the input of the SOA. Pump and probe signals are obtained from a DFB laser diode(${\lambda}_p$=1554 nm) and a tunable laser diode(${\lambda}_s$=1535 nm), respectively. The operation characteristics of the NOR logic device are successfully measured and demonstrated at the modulation frequency of 4.83 MHz.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.2
• /
• pp.26-38
• /
• 1994

We demonstrate a repeatless transmission of 2.5 Gbps digital signal over 98 km opticla filbers using optical transmitter and optcial receiver which are designed and implemented using commercially available devices. The optical transmitter is realized by using a distributed feedback(DFB) laser. Temperature of the laser is thermoelectrically stabilized and the output optical power is also stabilized by using negative feedback. The output power of the transmitter is 0 dBm. The optical receiver consists of an InGaAs avalanche photodiode, a preamplifier. an automatic gain control amplifier, and a clock/data regenerator. We find an optimum decision threshold that gives the best receiver sensitivity form the measured V curve. The best sensitivity is -35.5dBm( BER-1*10S010T, PRBS=2S023T -1 ) and the overload power is -9 dBm. Finally, we achieve error free optical transmission with 98 km optical fibers. The exinction ration penalty of 2 dB. the chromatic dispersion penalty of 1 dB, and the total power penalty of 3.0 dB are measured. These results satisfy CCITT recommendation.

• Korean Journal of Optics and Photonics
• /
• v.18 no.4
• /
• pp.235-240
• /
• 2007

A ceramic stem based TO package incorporating a coplanar waveguide feed-line has been proposed allowing for 10 Gbps grade data transmission. The frequency response of a cylindrical feed-line fer a conventional metal based TO package was first analyzed, and compared with that of the CPW feed-line used for a ceramic based package such as a butterfly package. For the case where a DFB LD chip is packaged to an LD module, the measured 3 dB frequency bandwidths for the conventional and proposed packages were 3.5 GHz and 7.8 GHz respectively, which agree well with the theoretical results obtained from the modeling based on the small signal equivalent circuits. Consequently, we proposed a novel ceramic based TO package with a CPW feed-line in ceramic material as a stem to improve the frequency characteristics of the conventional one. And, its performance was theoretically observed to confirm that the proposed package provides even wider frequency bandwidth compared to the conventional one.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2001.11a
• /
• pp.111-114
• /
• 2001

Optical transmitter and receiver are the essential components for optical communication. For these components, butterfly type packages are used which are comprised of metal housing, multilayer ceramic inserts, lead and window. In this study, 2.5 Gbps DFB(Distributed -Feedback) LD(Laser Diode) package was fabricated and characterized. Metal housing showed good thermal conductivity (200W/mK) and well matched TCE(6.7ppm/K) with GaAs chip. Ceramic inserts also showed good VSWR(Voltage Standing Wave Ratio) characteristics(<2.0). By brazing technology, all the elements were combined and sealed. RF characteristics of the package mounted on the PWB was also tested.

• Journal of Sensor Science and Technology
• /
• v.20 no.1
• /
• pp.8-13
• /
• 2011

We present measurements of the Brillouin frequency shift in an optical fiber using a 1550 nm distributed feedback laser diode(DFB-LD) as a light source. By modulating the probe light with an electro-optic modulator, we confirm the stimulated Brillouin gain spectrum(BGS) and spontaneous BGS using the coherent detection method. We also confirm the applicability of the technique to distributed temperature sensors that measure the change in Brillouin frequency shift due to temperature variations.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.02a
• /
• pp.136-137
• /
• 2003

데이터 통신의 지속적인 수요증가로 그동안 충분한 투자가 없었던 메트로망 영역과 가입자망 영역의 광부품 수요는 지속적으로 계속될 것이며, 메트로 기간망 영역의 변조속도도 622Mbit／s, 2.5Gbit／s에서 2.5Gbit／s와 10Gbit／s가 같이 사용되는 상황이 예상된다. 현재까지 10Gbit／s 광송신기에는 성능이 증명된 리튬나이오베이트(LN) 광변조기가 주로 사용되고 있었으나 최근의 메트로 광통신에서는 전송거리에 따라 소형이고 가격이 저렴한 EML 혹은 uncooled DFB 레이저의 사용이 증가하고 있다. (중략)

• ETRI Journal
• /
• v.31 no.6
• /
• pp.765-769
• /
• 2009

In this paper, we present the fabrication of 40 Gb/s traveling-wave electroabsorption modulator-integrated laser (TW-EML) modules. A selective area growth method is first employed in 40 Gb/s EML fabrication to simultaneously provide active layers for lasers and modulators. The 3 dB bandwidth of a TW-EML module is measured to be 34 GHz, which is wider than that of a lumped EML module. The 40 Gb/s non-return-to-zero eye diagram shows clear openings with an average output power of +0.5 dBm.

• Korean Journal of Optics and Photonics
• /
• v.16 no.1
• /
• pp.13-20
• /
• 2005

Fiber-Bragg-grating external cavity laser(FGL) modules were fabricated and experimentally analyzed. Proposed as a cost-effective solution for optical sources in the WDM-PON access network, FGL modules were packaged to TO-CAN type. We obtained a low threshold current of 13 mA, and an optical output power of 3.6 mW with a bias current of 60 mA at $25^{\circ}C$. The lasing wavelength dependencies on current and temperature were as small as 5.2 pm/mA and 30 pm/$^{\circ}C$, respectively. These change rates of the wavelength with the temperature and current are smaller than those of the DFB laser. Single-mode oscillations with the side-mode suppression ratio(SMSR) over 30 dB are maintained above the threshold current level. The FGL modules can be directly modulated at 155 Mbps, PRBS(2$^{23}$ -1) NRZ signal. Through the BER plots, we did not see the significant degradations before and after the transmission over 20km of the SMF at 155 Mb/s.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.8
• /
• pp.2037-2042
• /
• 2014

Three methods for gain saturation tone application were compared for optical wavelength division multiplexing transmission using more than 32 channels. The methods are to use high power distributed feedback laser diodes, to use amplified light sources, and lastly to use one saturation tone and several WDM light sources. 1532.3 nm, 1545.7 nm, and 1558.2 nm for the wavelength dependency of the saturation tone were also compared. As a result, the effect of amplified spontaneous emission noise caused by an amplifier was very slight. long wavelength for a saturation tone caused 1 dB gain reduction and its reason was analyzed.