• Journal of IKEEE
• /
• v.20 no.1
• /
• pp.45-53
• /
• 2016

This paper presents a CMOS interface circuit for vibration energy harvesting with MPPT (Maximum Power Point Tracking). In the proposed system a PMU (Power Management Unit) is employed at the output of a DC-DC boost converter to provide a regulated output with low-cost and simple architecture. In addition an MPPT controller using FOC (Fractional Open Circuit) technique is designed to harvest maximum power from vibration devices and increase efficiency of overall system. The AC signal from vibration devices is converted into a DC signal by an AC-DC converter, and then boosted through the DC-DC boost converter. The boosted signal is converted into a duty-cycled and regulated signal and delivered to loads by the PMU. A full-wave rectifier using active diodes is used as the AC-DC converter for high efficiency, and a DC-DC boost converter architecture using a schottky diode is employed for a simple control circuitry. The proposed circuit has been designed in a 0.35um CMOS process, and the designed chip occupies $915{\mu}m{\times}895{\mu}m$. Simulation results shows that the maximum power efficiency of the entire system is 83.4%.

• Journal of Satellite, Information and Communications
• /
• v.12 no.2
• /
• pp.89-93
• /
• 2017

This paper introduces an energy harvesting system that generates energy by collecting multi-band RF signals using buck-boost DC-DC converter. In an environment where the resistance of load using the collected electric energy is constantly changing, a buck-boost DC-DC converter is used in which the input resistance of the DC-DC converter does not change even if the load resistance changes. Since the frequency band of the input RF signal varies, the rectifier is designed for each band so that multiple bands can be processed, and a matching circuit is added to each band in front of the rectifier. For a rectifier to collect very small RF signals, a circuit is designed so that a constant voltage is obtained according to a very small input signal by devising a method of continuously accumulating the voltages collected and generated in each band. It is confirmed that the output efficiency can reach up to 20% even for the RF signal having the input of -20 dBm.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.1
• /
• pp.139-144
• /
• 2016

This paper describes functional circuits of DC-DC converter IC incorporated with variable frequency PFM technique. In case of output voltage of DC-DC converter is reached setting value or output current is low then PFM switching frequency is slow down. In this work a PFM signal generator, a PFM Frequency Control Circuit, an output voltage detector and an over current protection circuits are designed. This device has been designed at a $0.35[{\mu}m]$, double poly, double metal 12[V] CMOS process.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1037_1038
• /
• 2009

본 논문에서는 디지털 제어방식의 DC-DC컨버터를 이용한 계통연계형 전력변환기를 제안한다. 제안하는 전력변환기는 3상 전류형 능동클램프 DC-DC컨버터와 계통연계형 3상 인버터로 구성되어 있다. 제안하는 전력변환기의 동작을 분석하기 위해 PSCAD/EMTDC를 이용하여 연료전지의 출력 동특성을 나타내는 모델과 제안하는 전력변환기의 모델을 개발하였다. 시뮬레이션모델의 검증이 가능한 하드웨어장치의 기본설계를 실시하였다. 제안하는 전력변환기는 정격출력에서 저전압특성을 갖는 연료전지를 전력계통에 고효율로 연계하는데 유용할 것으로 보인다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.7A
• /
• pp.568-573
• /
• 2009

This paper presents a step-down DC-DC converter with On-chip Compensation for battery-operated portable electronic devices which are designed in O.13um CMOS standard process. In an effort to decrease system volume, this paper proposes the on chip compensation circuit using capacitor multiplier method. Capacitor multiplier method can minimize error amplifier's compensation capacitor size by 10%. It allows the compensation block of DC-DC converter be easily integrated on a chip and occupy less layout area. But capacitor multiplier operation reduces DC-DC converter efficiency. As a result, this converter shows maximum efficiency over 87.2% for the output voltage of 1.2V (input voltage : 3.3V), maximum load current 500mA, and 25mA output ripple current. This voltage mode controled buck converter has 1MHz switching frequency.

• Journal of Industrial Technology
• /
• v.30 no.A
• /
• pp.69-73
• /
• 2010

In this paper, we designed the RF-DC converter used in wireless power transmission system and studied how to design the RF-DC converter of high conversion efficiency. The RF-DC converter operate at 2.45GHz and the diode is connected with series. The RF-DC converter uses shorted stub for DC loop and matching. We can divide the RF-DC converter circuit into four blocks. The reflection coefficients between the blocks were optimized for the maximum conversion efficiency at 0 dBm input power and $1300{\Omega}$ load impedance. The final design of the RF-DC converter has a 52 percent conversion efficiency.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.4
• /
• pp.119-125
• /
• 2022

The power supply for the anti-aircraft radar homing sensor should allow the system to receive power quickly and stably without the influence of noise. For this purpose, DC-DC converters are widely used for reliable power conversion. Also, switching of DC-DC converters Frequency noise should not cause false alarms and ghosts that may affect the detection and tracking performance of the system, and it should have a check function that can monitor power in real time while the homing sensor is operating. In order to apply to anti-aircraft radar homing sensor, we developed a multi-output switching power supply with maximum output 𐩒𐩒𐩒 W, efficiency 80% or more (@100% load), output power by receiving 28VDC input, and power supply to achieve more than 80% efficiency. A DC-DC converter was applied to this large output, and the multi-output flyback method was applied to the rest of the low-power output.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.1061-1067
• /
• 2019

In this paper, a highly integrated 3-channel DC-DC converter is designed using power transistor width scaling (PTWS). For positive voltage, $V_{POS}$, a boost converter is designed using the set-time variable pulse width modultaion (SPWM) dual-mode and PTWS to improve efficiency at light load. For negative voltage, $V_{NEG}$, a 0.5 x regulated inverting charge pump is designed with pulse skipping modulation (PSM) controller to reduce power consumption, and for an additional positive voltage, $V_{AVDD}$, a LDO circuit is designed. The proposed DC-DC converter has been designed using a $0.18{\mu}m$ BCDMOS process. Simulation results show that the proposed converter has power efficiency of 56%~90% for load current range of 1 mA~70 mA and output ripple voltage less than 5 mV at positive voltage.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.10 s.340
• /
• pp.39-46
• /
• 2005

A DC-DC converter with digital controller is realized. the digital controller has several advantages such as robustness, fast design time, and high flexibility. however, since the DC-DC output voltage is analog, an analog-to-digital conversion scheme is always essential in all digital controllers. A simple and efficient delta-sigma modulator is used as a conversion scheme in out implementation. The measurement results show good voltage regulation

• Proceedings of the KIEE Conference
• /
• 2009.04b
• /
• pp.209-211
• /
• 2009

본 논문에서는 고효율 DC-DC 컨버터와 인버터에 의한 연료전지발전용 전력변환기를 제안한다. 제안하는 전력변환기는 Boost Converter와 LLC공진 컨버터의 2 stage 조합으로 구성되어 있다. 제안하는 전력변환기의 동작을 분석하기 위해 PSCAD/EMTDC를 이용하여 연료전지의 출력 동특성을 나타내는 모델과 제안하는 전력변환기의 모델을 개발하였다. 시뮬레이션모델의 검증을 위해 하드웨어장치를 구성하여 실험을 실시하였다. 제안하는 전력변환기는 정격출력에서 저전압특성을 갖는 연료전지를 전력계통에 고효율로 연계하는데 유용할 것으로 보인다.