• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.773-778
• /
• 2001

This paper describes the implementation of the vector control schemes for a variable-speed 131kW PMSM (Permanent Magnet Synchronous Motor) in super-high speed application. The vector control with synchronous reference frame current regulator has been implemented with the challenging requirements such as the extremely low stator inductance$(28^{\mu}H)$, the high dc link voltage(600V) and the high excitation frequency(1.2kHz). Because the conventional position sensor is not reliable in super-high speed, a vector control scheme without any position sensor has been proposed. The proposed sensorless algorithm is implemented by processing the output voltage of the PI current regulator, and hence the structure is simple and the estimated speed is robust to the measurement noise. The experimental system has been built and the proposed control has been implemented and evaluated. The test result, up to the speed of 60,000 r/min, shows the validity of the proposed control.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.3
• /
• pp.110-113
• /
• 2011

Platform Screen Door, PSD, is a device that seeks to prevent accidents with regards to falling off the platform and getting trapped between the trains, achieve improvements on the cleanliness of the air, address the accessibility issue of the disabled and the elderly and provide fresher environment on the platform in general. This is achieved by preventing health hazards and accidents from occurring through installation of fixed and moving doors between rail, tram and subway platforms and the railway. Domestic firms have achieved domestic production to a large degree in various Control Units including the Overall Control Unit and RF devices through investments in technology. Despite this, full domestic production of the core of the PSD system, Door Control Unit, DCU, is not yet achieved, having to install PSDs in a relatively short period of time. Currently, controllers with DC motors are developed for installation or one is faced with having to import foreign produced controllers. In this research, the control unit prototype using the BLDC motor was domestically produced. The performance of the control unit was rigorously tested through installation on Eun-Ha Rail on Wol-Mi Island.

• Journal of Advanced Marine Engineering and Technology
• /
• v.15 no.1
• /
• pp.85-95
• /
• 1991

All physical systems are nonlinear to some degree. The examples are relay, backlash, deadzone, saturation element and so on. In the linear control system design, it is useful method to restrict the nonlinearity to the linearity of system over the operation range. It is worth noting that nonlinearities may be intentionally introduced in to a system. A simple of an intentional non-linearity is the Bang-Bang controller which uses the On-Off relay. In this paper, an angular position servosystem made of a DC servomotor controlled by a microcomputer is discribed. Authors use two methods in the design of controller. The one is linear controller designed by the optimal feedback control theory only and the other is nonlinear controller designed by On-Off relay with optimal feedback control theory. To do the real time control, the controller is designed by using 16bit personal computer and A/D.D/A converter(12bit) is used in order to convert the signal. According to this way, the results from real time control are as follows. 2) Under the On-Off controller with hysterisis the influence of disturbance is considerably smaller than the linerar controller. 3) An increase in the sampling period has a destabilizing effect. 4)In the controller performance, the response time of the On-Off controller is longer than that of the linear controller. To close, we note that the On-Off controller with hysterisis is more attractive than the linear controller in the presence of the input limit.

• Journal of Institute of Control, Robotics and Systems
• /
• v.2 no.3
• /
• pp.181-187
• /
• 1996

A frictionless positioning device using cone-shaped active magnetic bearings(AMBs) is developed, which is driven by a brushless DC motor equipped with resolver. The cone-shaped AMB feature that the structure is simple and yet the five d.o.f. rotor motion is controlled by four magnet pairs. A linearized dynamic model, which accounts for the relationship between input voltage and output current in the cone-shaped magnet, is developed and the azimuth motion of the frictionless positioning device is modeled as the second order system. The feedback controller is designed by using linear quadratic regulator with integral action optimal control law so that the cone-shaped AMB system is stabilized and the frictionless positioning device gets the zero steady state. It is observed that the linearized dynamic model is adequate and the frictionless positioning device can achieve the tracking accuracy within the sensor resolution.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.13 no.3
• /
• pp.11-17
• /
• 2017

The aerial support air sculptures currently exhibited in indoor spaces are similar to simple ad balloons, using multiple rope strands. Users now want more advanced unfixed sculptures, and hope these will develop into buoyant sculptures that can maintain the attitudes that users want on their own. This study investigated an attitude control system for unfixed levitation sculptures that can levitate with no rope and continuously maintain a certain attitude at a height specified by the user. To facilitate levitation, the exterior part of the sculpture was made of lightweight fibers, and the interior part was filled with helium gas. The controller was composed of a microprocessor of the dsPIC30F line from microchip, gyro, acceleration, and earth magnetic field sensors, and a highly efficient brushless DC (BLDC) electric motor. The attitude and position control system requires scheduling considering the trajectories of the sculpture and the control system, because the roles of the overall components are more important than those of a single controller. Furthermore, the system was designed like a fusion system that is expanded and controlled as a total controller, because it is interconnected with various sensors. The attitude control system of buoyant sculptures was implemented in this study, such that it can actively cope with the position, direction, stopping, and time aspects. The system performance was then evaluated.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.55 no.8
• /
• pp.353-362
• /
• 2006

This paper illustrates the practical design procedure on a position control of an electrical fin actuator for the guided missile using Time Delay Control(TDC) and Enhanced Time Delay Observer(ETDO). Since TDC is robust to the model uncertainties such as the parameter variation and the external disturbance, it has been frequently used in nonlinear control systems. For a position control of an electrical fin actuator in the missile system, TDC requires the velocity sensor as well as the position sensor. To resolve the problems of the cost, the space and the malfunction due to the velocity sensor, ETDO is used as the velocity observer. ETDO is enhanced version of TDO that has the problems of the reconstruction errors and the restriction on selecting its gains. To maximize the control performance, the parameters of ETDO are optimized by using the genetic algorithm. The effectiveness of this approach is proved through a series of simulation studies and experiments, and the designed controller is compared with the typical TDC and TDC using the reduced oder observer.

• Journal of Power Electronics
• /
• v.9 no.4
• /
• pp.654-666
• /
• 2009

Direct torque control (DTC) of induction machines (IM) is a well-known strategy of these drives control which has a fast dynamic and a good tracking response. In this paper a nonlinear DTC of speed sensorless IM drives is presented which is based on input-output feedback linearization control theory. The IM model includes iron losses using a speed dependent shunt resistance which is determined through some effective experiments. A stator flux vector is estimated through a simple integrator based on stator voltage equations in the stationary frame. A novel method is introduced for DC offset compensation which is a major problem of AC machines, especially at low speeds. Rotor speed is also determined using a rotor flux sliding-mode (SM) observer which is capable of rotor flux space vector and rotor speed simultaneous estimation. In addition, stator and rotor resistances are estimated using a simple but effective recursive least squares (RLS) method combined with the so-called SM observer. The proposed control idea is experimentally implemented in real time using a FPGA board synchronized with a personal computer (PC). Simulation and experimental results are presented to show the capability and validity of the proposed control method.

• Publications of The Korean Astronomical Society
• /
• v.21 no.2
• /
• pp.81-86
• /
• 2006

Even though 30inch optical telescope at Kyung Hee Astronomy Observatory has been used to produce a series of scientific achievements since its first light in 1992, numerous difficulties in operating of the telescope have hindered the precise observations needed for further researches. Since the currently used PC-TCS(Personal Computer based Telescope Control System) software based on ISA-bus type is outdated, it doesn't have a user friendly interface and make it impossible to scale. Also accumulated errors which are generated by discordance from input and output signals into a motion controller required new control system. Thus we have improved the telescope control system by updating software and modifying mechanical parts. We applied a new BLDC(brushless DC) servo motor system to the mechanical parts of the telescope and developed a control software using Visual Basic6.0. As a result, we could achieve a high accuracy in controlling of the telescope and use the user friendly GUI(Graphic User Interface).

• Proceedings of the KSR Conference
• /
• 1999.11a
• /
• pp.267-272
• /
• 1999

The auxiliary power supply system fur passenger service of railway car has been developed from MA(Motor-Alternator) to CVCF Inverter (Static Inverter). Generally, a customer wants to apply tile new control method and device for auxiliary power supply of railcar However, if the auxiliary power supply is supplied to extended existing line, the maintenance cost of the old system is less expensive than new developed system, so, the customer specifies that the auxiliary power supply has compatibility with existing one completely. At that time, the hardware is nearly same as existing system except small changes of accessories for better performance. This paper describes the flicker control using feed-forward method of auxiliary power supply system for new 50 electric railcars, which are delivered to Korean National Railroad (KNR) Kwa-chon Line. The existing power supply system has damping resistor box to stabilize the DC input (1.5 ㎸). At this time, for better system efficiency the new system has not include resistor box but new control method including feed-forward control is applied. This control algorithm realizes the better stabilization of input power compared to the result of the existing system, which includes resistor box

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.4
• /
• pp.659-666
• /
• 2006

Servo-motors are used as key components of automated system by performing precise motion control as accurate positioning and accurate speed regulation in response to the commands from computers and sensors. Especially, the linear brushless servo-motors have numerous advantages over the rotary servo motors which have connection with the friction induced transfer mechanism such as ball screws, timing belts, rack/pinion. This paper proposes an estimation method of unknown motor system parameters using the informations from the sinusoidal driving type linear brushless DC motor dynamics and outputs. The estimated parameters can be used to tune the controller gain and a disturbance observer. In order to meet this purpose high performance Digital Signal Processor, TMS320F240, designed originally for implementation of a Field Oriented Control(FOC) technology is adopted as a controller of the liner BLDC servo motor. Having A/D converters, PWM generators, rich I/O port internally, this servo motor application specific DSP play an important role in servo motor controller. This linear BLDC servo motor system also contains IPM(Intelligent Power Module) driver and hail sensor type current sensor module, photocoupler module for isolation of gate signals and fault signals.