• Proceedings of the Materials Research Society of Korea Conference
• /
• 1993.05a
• /
• pp.56-57
• /
• 1993

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2000.11a
• /
• pp.79-79
• /
• 2000

• Journal of the Korean institute of surface engineering
• /
• v.41 no.5
• /
• pp.214-219
• /
• 2008

Indium tin oxide (ITO) films were deposited on PET substrate by RF superimposed DC magnetron sputtering using ITO (doped with 10 wt% $SnO_2$) target. Substrate temperature was maintained below $750^{\circ}C$ without intentionally substrate heating during the deposition. The discharge voltage of DC power supply was decreased from 280 V to 100 V when superimposed RF power was increased from 0 W to 150 W. The electrical properties of the ITO films were improved with increasing of superimposed RF power. In the result of cyclic bending test, relatively high mechanical property was obtained for the ITO film deposited with RF power of 75 W under DC current of 0.75 A which could be attributed to the decrease of internal stress caused by decrease in both deposition rate and plasma impedance.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.6
• /
• pp.593-600
• /
• 2013

The asymmetric pulsed DC reactive magnetron sputtering system is widely used for the high quality plasma sputtering process such as a thin film deposition. In asymmetric pulsed DC power supply a reverse voltage is applied to the target periodically to minimize arc discharging effect. When sputtering in the mid-frequency range (20-350 kHz), the periodic target voltage reversals suppress arc formation at the target and provide long-term process stability. Thus, high quality, defect-free coatings of these materials can now be deposited at competitive rates. In this paper, a new style asymmetric pulsed DC power supply including mid-transformer is presented. In the proposed, an energy recovery circuit is adopted to reduce the mutual inductance of the transformer. As a result, the system dynamics of the voltage control loop is increased highly and the non-linear voltage boosting effect of the conventional system is removed. This work was proved through simulation and laboratory based experimental study.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.379-380
• /
• 2007

The characteristics of a co-sputtered indium zinc tin oxide (IZTO) films prepared by dual target dc magnetron sputtering from IZO and ITO targets at a room temperature are investigated. Film properties, such as sheet resistance, optical transmittance, surface work function and surface roughness were examined as a function of ITO dc power at constant IZO dc power of 100 W. It was shown that the increase of the ITO dc power during co-sputtering of ITO and IZO target resulted in an increase of sheet resistance of the IZTO films. This can be attributed to high resistivity of ITO film prepared at room temperature. Surface smoothness and roughness were investigated by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). The synchrotron x-ray scattering results obtained from IZTO film with different ITO contents showed that introduction of ITO atoms into amorphous IZO film resulted in a crystallization of IZTO film with (222) preferred orientation due to low alc transition temperature of ITO film. However, the transmittance of the IZTO films with thickness of 150 nm is between 80 and 85 % at wavelength of 550 nm regardless of ITO content. Possible mechanism to explain the ITO and IZO co-sputtering effect on properties of IZTO is suggested.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.103.2-103.2
• /
• 2017

Nanocrystalline HfN coatings were prepared by reactively sputtering Hf metal target with N2 gas using a magnetron sputtering system operated in DC and ABPP (asymmetric bipolar pulsed plasma) condition with various duties and frequencies. The effects of duty and frequency, ranging from 75 to 100 % and 5 to 50 kHz, on the coating microstructure, crystallographic and mechanical properties were systematically investigated with FE-SEM, AFM, XRD and nanoindentation. The results show that pulsed plasma has a significant influence on coating microstructure and mechanical properties of HfN coatings. Coating microstructure evolves from the columnar structure to a highly dense one as duty decreases. Average grain size and nano hardness of HfN coatings were also investigated with various pulsed conditions.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.337-337
• /
• 2012

단일 결정의 Ge 박막은 0.67 eV의 작은 밴드갭을 가지고 있기에 장파장의 빛을 흡수하기 위한 목적으로 태양전지 분야에서 집중적인 연구가 진행되어지고 있다. 또한, Si에 비하여 높은 전하 이동도를 가지고 있기에 박막 트랜지스터로의 응용 연구들이 진행되고 있는 중이다. 전자 소자로써 큰 효과를 가지고 오기 위해서는 양질의 Ge 결정박막을 성장하여야 한다. 이를 위하여 다양한 공정 방법으로 Ge 박막의 결정성 향상에 대한 연구들을 진행하고 있다. 그중 본 연구에서는 ICP-assisted DC sputtering 방법을 이용하여 저온(${\sim}230^{\circ}C$) Ge 박막 결정성장에 대한 연구를 진행하였다. Ge 박막을 유리기판(Eagle 2000) 위에 증착하였으며, $6{\times}10^{-6}$ Torr 이하의 기본 압력에서 공정을 진행하였다. 7 mTorr의 Ar 분위기에서 타겟에 인가되는 전압 및 전류를 변화 시키며 Ge 박막 증착에 미치는 영향에 대해서 연구를 진행하였다. 기본적인 DC sputtering 방법을 이용하여 박막을 증착하였을 경우 증착한 모든 샘플에서 결정성을 확인하였으며, 낮은 전압에서도 결정화가 일어나는 것을 확인 할 수 있었다. 또한 전압을 증가시켜도 결정화 정도가 일정하게 유지됨을 확인 할 수 있었다. 다만 이 경우에는 결정의 방향이 랜덤하게 형성되었으며, DC sputtering 방법을 이용하여 저온에서 공정을 진행하였기에 박막은 수십 nm의 columnar grain을 형성하였다. ICP를 이용한 DC sputtering 방법을 이용하여 박막을 증착 하였을 경우, 일정 전압 이하에서는 비정질의 Ge 박막이 균일하게 형성됨을 확인 할 수 있었으며, 이후 결정화 정도가 타겟에 인가되는 전압에 비례하여 증가하였다. 또한, 이때 증착된 Ge 박막은 단일 결정으로 형성되었음을 확인 할 수 있었다. 이는 박막 성장시 ICP에 의해서 생성된 Ar 이온이 표면으로 가속화됨으로 인하여 Ge 박막 표면에서 channeling 효과가 나타남으로 인하여 <110> 방향으로 결정이 정열된 것으로 보인다.

• Korean Journal of Materials Research
• /
• v.9 no.5
• /
• pp.533-537
• /
• 1999

ATO(Sb doped $SnO_2$) thin films whose thicknesses were 600, 1100 and $2100\AA$ were prepared by DC magnetron sputtering method. They showed the lowest resistivity at DC sputtering power 0.24kW and had lower resistivity with increasing thickness. The power dependence of resistivity among ATO thin films was also different with thickness. The increase of carrier concentration in ATO thin films was responsible for the decrease of resistivity with thickness increase. ATO thin films which were prepared at 30sccm oxygen flow rate showed a great change of sheet resistance under 1M HCl solution. The investigation of SAM(Scanning Auger Microprobe) revealed that oxygen atomic percentage on the surface of ATO thin films was changed. The decrease of sheet resistance also occurred when ATO thin films, prepared at 30sccm oxygen flow rate, were exposed to air for a long period of time. For this reason, it was considered that the desorption of oxygen on ATO surface was accelerated by HCl.

• Journal of the Korean Ceramic Society
• /
• v.33 no.5
• /
• pp.514-518
• /
• 1996

Sb doped SnO2(ATO: Antinomy doped Tin Oxide) thin films were prepared by a DC magnetron spttuering method using an oxide target and the electrical characteristics of ATO films were investigated. The experimen-tal conditions are as follows :Ar flow rate ; 0~100 sccm deposition tempera-ture ; 250~40$0^{\circ}C$ DC sputter powder ; 150~550W and sputteing pressure ; 2~7 mTorr, The thickness of depositied ATO films were 600$\AA$~1100 $\AA$ ranges. The resistivity of ATO films was decreased due to the increase of the crystallinity of ATO films with deposition temperature. The decrease of carrier concentration of films with the increase of oxygen flow rate and working pressure is responsible for the increase of resistivity. Increasing of sputtering power raised the resistivity of films by decreasing the carrier mobility.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.143-147
• /
• 2002

In this paper, we investigated the deposition condition of Bragg reflector formation that will be expected to play an important role in future FBAR device applications. The thin films were deposited using an RF/DC magnetron sputtering technique. The material characteristics such as deposition rates, grain structures and surface roughnesses of the deposited silicon dioxide (SiO$_2$) and tungsten (W) films were investigated for various deposition conditions. As a result, it was found that the deposition condition could significantly affect the material characteristics of the deposited films and also the optimization of the deposition process is essentially important to obtain the desirable Brags reflector structure consisted of high-quality in films.