• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.2195_2196
• /
• 2009

DC-offset is a very important subject in power systems protection, since DC-offset causes mal-operation of the distance relay. This paper deals with the influence of a FIR filter used for removing the DC-offset upon the convergence characteristics of distance relaying algorithm based on Fourier Transform.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.9
• /
• pp.953-959
• /
• 1992

As the TC(time-current) curve corresponding to symmetrical time invariant RMS value has been traditionally chosen and used for setting the relay, it has caused the misoperation errors on relay coordination because of CT secondary current being actually an asymmetrical time varying RMS value. In this paper, an algorithm for calculating the relay operating time is developed to study the asymmetrical effect using the step-by-step method. We represent the relay operating time errors between with and without DC offset versus PSM(plug setting multiplier), TMS(time multiplier setting) and X/R ratio. And also we present the correction factor. Finally we confirm the validity of this technique through the case study.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.969-974
• /
• 2003

A simple and cost-effective method for the electrostatic suspension of thin plates like silicon wafers is proposed which is based on a switched voltage control scheme. It operates according to a relay feedback control and deploys only a single high-voltage power supply that can deliver a dc voltage of positive and/or negative polarity. This method possesses the unique feature that no high-voltage amplifiers are needed which leads to a remarkable system simplification relative to conventional methods. It is shown that despite the inherent limit cycle property of the relay feedback based control, an excellent performance in vibration suppression is attained due to the presence of a relatively large squeeze film damping origination from the air between the electrodes and levitated object. Using this scheme, a 4-inch silicon wafer was levitated stably with airgap variation decreasing down to 1 $\mu\textrm{m}$ at an airgap of 100 $\mu\textrm{m}$

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.10 s.175
• /
• pp.56-64
• /
• 2005

A simple and cost-effective method for the electrostatic suspension of thin plates like silicon wafers is proposed which is based on a switched voltage control scheme. It operates according to a relay feedback control and deploys only a single high-voltage power supply that can deliver a DC voltage of positive and/or negative polarity. This method possesses the unique feature that no high-voltage amplifiers are needed which leads to a remarkable system simplification relative to conventional methods. It is shown that despite the inherent limit cycle property of the relay feedback based control, an excellent performance in vibration suppression is attained due to the presence of a relatively large squeeze film damping origination from the air between the electrodes and levitated object. Using this scheme, a 4-inch silicon wafer was levitated stably with airgap variation decreasing down to $1 {\mu}m$ at an airgap of $100{\mu}m$.

• Proceedings of the KIEE Conference
• /
• 2008.11a
• /
• pp.12-15
• /
• 2008

A distance relay has been widely used for transmission line protection. The distance relay detects a fault based on the calculated impedance i.e. the ratio of the voltage to the current measured from a current transformer (CT) and a coupling capacitor voltage transformer (CCVT), respectively. When a fault occurs and a CT saturates due to the magnitude of fault current, dc component, primary time constant, and the remanent flux of the iron core, the secondary current of a CT is distorted On the other hand, non-fundamental components generated during a fault can increase the error of a CCVT, particularly when a fault distance is short. The distortion of the current and voltage can cause mal-operation or the operating time delay of a distance relay. This paper describes the response of a distance relay considering the errors of a CT and a CCVT. The results indicate that the severe distortion of a CT and a CCVT have noticeable effect to a distance relay.

• Proceedings of the KIEE Conference
• /
• 2001.05a
• /
• pp.38-41
• /
• 2001

This paper presents a digital current differential protection algorithm for a transformer in power system. This algorithm uses an FIR filter to improve the performance of the relay. This paper presents a practical method setting the operating slope of the relay and reduce ct mismatch. A series of EMTP simulation results have shown effectiveness of the algorithm under various type of transformers and conditions.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.157.2-157
• /
• 2001

This paper describes the synergism of Artificial Neural Network and Fuzzy Logic based approach to improve the reliability of transformer differential protection, the conventional transformer differential protection commonly used a harmonic restraint principle to prevent a tripping from inrush current during initial transformer´s energization but such a principle can not performs the best optimization on tripping time. Furthermore, in some cases there may be false operation such as during CT saturation, high DC offset or harmonic containing in the line. Therefore an artificial neural network and fuzzy logic has been proposed to improve reliability of the transformer protection relay. By using EMTP-ATP the power transformer is modeled, all currents flowing ...

• Proceedings of the KSR Conference
• /
• 2006.05b
• /
• pp.1088-1095
• /
• 2006

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.788-792
• /
• 2007

국내외의 자동차 메이커는 고효율, 저공해 자동차 개발에 집중하고 있으며, 그 방법으로 하이브리드 자동차가 최우선시 되고 있다. 하이브리드 자동차의 밧데리 팩을 구성하는 핵심 부품 중 하나인 고전압 직류 릴레이는 주행 중 엔진 구동력을 보조하는 구동모터에 전기 에너지를 공급하는 밧데리의 출력을 개폐하는 기기이다. 고전압 직류 릴레이의 개폐 동작시 발생하는 소음은 자동차 운전 중 실내로 유입되어 운전자의 승차감을 떨어뜨리는 요인이 되므로 릴레이의 개폐 동작시 발생하는 소음 저감을 위한 연구가 필요하다. 본 연구에서는 폐로(ON) 동작시 발생하는 소음 저감을 위해 소음원인 충격력을 감소시키기 위한 이중 접압스프링 구조를 제안하였으며, 소음 저감 성능평가를 수행하였다. 먼저 정확한 충격해석을 위해 고전압 직류 릴레이의 최소 동작 전압인 5.9V부터 상시 인가 전압인 12V까지 총 6개의 전압레벨에서 릴레이의 전자력을 측정하였으며, 기존 접압스프링 구조와 이중 접압스프링 구조에 관하여 외연적 탄소성 유한요소 프로그램인 LS-DYNA를 사용하여 충격해석을 수행하였다. 고전압 직류 릴레이의 소음원인 가동전극과 고정전극에서 발생하는 일차 충격력과 가동철심과 고정철심에서 발생하는 이차 충격력을 비교, 평가하였다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.9
• /
• pp.47-56
• /
• 2012

This research is to develop satiable battery charger with a variety of capacity and voltage specifications of battery. For this, voltage or current were controlled through buck converter which is DC voltage that already received three-phase at primary side and passed bridge rectifier diode. And, it was comprised of full-bridge converter and HFTR for insulation and a square wave AC. The transformer primary side was comprised in series to divide certain charging current and the secondly side was comprised of 6 fixed transformers so that they can generate certain amount of power and various output voltage through relay parallel compound 6 DC Link outputs. To confirm such structure's verification and validity, simulation with PSIM was conducted, and validity of proposed variable charger system was verified through 3kW stack production.