• Elastomers and Composites
• /
• v.36 no.2
• /
• pp.111-120
• /
• 2001

Mechanical properties and their adhesion behavior with zinc- and brass-plated steel cords of natural rubber/acrylonitrile-butadiene blend compounds were investigated as a function of blend ratio. The Mooney viscosity and stress relaxation time were found to be lowered with increasing NBR content. Tensile modulus generally increased with increasing NBR content. Tensile stress at break stayed constant up to about 40 phr and showed minimum at $50{\sim}60 phr$, and thereafter increased with increasing NBR content. Strain at break decreased linearly below 50 phr, and above the level it showed nearly constant value. Based on the abrupt drops in elastic modulus and tan ${\delta}$ peak, the glass transition temperature of NR and NBR were found to be -55 and $-10^{\circ}C$, respectively. In the case of NR/NBR blend compounds, two distinct transition points were observed and each transition position was not affected by NBR level indicating an incompatible nature of NR/NBR blend system. The pullout force and rubber coverage decreased to the level of about 40% to that of pure m compound, when the 50 phr of NR was replaced by NBR. However, the pure NBR compound showed the comparable adhesion performance with NR(${\sim}90%$). The sulfur concentration was found to become lower with the increased NBR content at the adhesion interface based on the Auger spectrometer results, representing a lack of adhesion layer formation, and this was explained for a possible cause of low adhesion performance with adding NBR.

• Proceedings of the KOR-BRONCHOESO Conference
• /
• 1978.06a
• /
• pp.6.1-6
• /
• 1978

Dsysphagia or difficulty in swallowing is a symptom wich indicates the presence of disease or dysfunction. Because the cause & the original site are variable, it is significant to study the clinicostatistical analysis on 133 cases with complant of dysphagia during the last one year in the department of Otolaryngology, College of Medicine, Seoul National University. The results are as follows; 1) Among the total O.P.D. patients (6313 cases), patients complaining the dysphagia are 2.1%. 2) Male to female sex ratio is 1. 3 to 1, slightly predominent in male and average are 35.7 years. 3) The duration of chief complaint is about 251 days in average, but excluding the 8 cases with more than year of symptom, it is about 40 days. In detailed analysis of the duration; 67 cases (50.4%) occurred within 1 weak: 24 cases (18.0%), 1 week to 1 month: 34 cases (25.6%), 1 month to 1 year: 8 cases (6.0%), more than 1 year. 4) As to the site of origin, the oropharyngolaryngeal origin 106 cases (76.7%) are 4 times as many as the esophageal origin 27 cases (20.3%). 5) As to the etiological classification: inflammation 67 cases (50.4%), tumor 28 cases (21.0%), corrosive agent 14 cases (10.5%), foreign body 11 cases (8.3%) in order. 6) As to the disease entity: pharyngitis and tonsillitis 42 cases (31.6%), stomatitis 14 cases (10.5%), corrosive esophagitis 14 cases (10.5%), laryngeal tumor 12 cases (9.0%), peritonsillar abscess 9 cases (6.8%), esophageal foreign body 7 cases (5.2%), tongue tumor 7 cases (5.2%), tonsillar tumor 6 cases (4.5%), (pharyngeal foreign body 4 cases (3.0%)in order.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.38 no.3
• /
• pp.258-268
• /
• 2001

The compression method is necessarily used to send the high quality moving picture that contains a number of data in image processing. In the field of moving picture compression method, the motion estimation algorithm is used to reduce the temporal redundancy. Block matching algorithm to be usually used is distinguished partial search algorithm with full search algorithm. Full search algorithm be used in this paper is the method to compare the reference block with entire block in the search window. It is very efficient and has simple data flow and control circuit. But the bigger the search window, the larger hardware size, because large computational operation is needed. In this paper, we design the full search block matching motion estimator. Using the DCT DC values, we decide luminance. And we apply 3 bit compare-selector using bit plane to I(Intra coded) picture, not using 8 bit luminance signals. Also it is suggested that use the same selective bit for the P(Predicted coded) and B(Bidirectional coded) picture. We compare based full search method with PSNR(Peak Signal to Noise Ratio) for C language modeling. Its condition is the reference block 8$\times$8, the search window 24$\times$24 and 352$\times$288 gray scale standard video images. The result has small difference that we cannot see. And we design the suggested motion estimator that hardware size is proved to reduce 38.3％ for structure I and 30.7％ for structure II. The memory is proved to reduce 31.3％ for structure I and II.

• Korean Journal of Optics and Photonics
• /
• v.31 no.2
• /
• pp.59-70
• /
• 2020

We discuss a modified numerical model based on the Monte Carlo radiative transfer (MCRT) method, i.e., the MCRT matrix method, for the analysis of atmospheric scattering effects in three-dimensional flash LIDAR systems. Based on the MCRT method, the radiative transfer function for a LIDAR signal is constructed in a form of a matrix, which corresponds to the characteristic response. Exploiting the superposition and convolution of the characteristic response matrices under the paraxial approximation, an extended computer simulation model of an overall flash LIDAR system is developed. The MCRT matrix method substantially reduces the number of tracking signals, which may grow excessively in the case of conventional Monte Carlo methods. Consequently, it can readily yield fast acquisition of the signal response under various scattering conditions and LIDAR-system configurations. Using the computational model based on the MCRT matrix method, we carry out numerical simulations of a three-dimensional flash LIDAR system operating under different atmospheric conditions, varying the scattering coefficient in terms of visible distance. We numerically analyze various phenomena caused by scattering effects in this system, such as degradation of the signal-to-noise ratio, glitches, and spatiotemporal spread and time delay of the LIDAR signals. The MCRT matrix method is expected to be very effective in analyzing a variety of LIDAR systems, including flash LIDAR systems for autonomous driving.

• Korean Journal of Soil Science and Fertilizer
• /
• v.49 no.5
• /
• pp.598-607
• /
• 2016

This study was conducted to evaluate the amount of nitrogen (N) top dressing based on the normalized difference vegetation indices (NDVI) by ground based sensors for leaf perilla under the polyethylene house. Experimental design was the randomized complete block design for five N fertilization levels and conventional fertilization with 3 and 4 replications in Gumsan-gun and Milyang-si field, respectively. Dry weight (DW), concentration of N, and amount of N uptake by leaf perilla as well as NDVIs from sensors were measured monthly. Difference of growth characteristics among treatments in Gumsan field was wider than Milyang. SPAD-502 chlorophyll meter reading explained 43.4% of the variability in N content of leaves in Gumsan field at $150^{th}$ day after seedling (DAS) and 45.9% in Milyang at $239^{th}$ DAS. Indexes of red sensor (RNDVI) and amber sensor (ANDVI) at $172^{th}$ day after seedling (DAS) in Gumsan explained 50% and 57% of the variability in N content of leaves. RNDVI and ANDVI at $31^{th}$ DAS in Milyang explained 60% and 65% of the variability in DW of leaves. Based on the relationship between ANDVI and N application rate, ANDVI at $172^{th}$ DAS in Gumsan explained 57% of the variability in N application rate but non significant relationship in Milyang field. Average sufficiency index (SI) calculated from ratio of each measurement index per maximum index of ANDVI at $172^{th}$ DAS in Gumsan explained 73% of the variability in N application rate. Although the relationship between NDVIs and growth characteristics was various upon growing season, SI by NDVIs of ground based remote sensors at top dressing season was thought to be useful index for recommendation of N top dressing rate of leaf perilla.

• Journal of the Korean Magnetics Society
• /
• v.9 no.2
• /
• pp.78-84
• /
• 1999

$(Ni, Zn)Fe_2O_4$ powders were prepared through self-propagating high temperature synthesis reaction and the effects of initial zinc oxide powder size and oxygen pressure on the magnetic properties of the final combustion products were studied. The ferrite powders were combustion synthesized with iron, iron oxide, nickel oxide, and zinc oxide powders under various oxygen pressures of 0.5~10 atmosphere after blended in n-hexane solution for 5 minutes with a spex mill, followed by dried at 120 $^{\circ}C$ in vacuum for 24 hours. The maximum combustion temperature and propagating rate were about 1250 $^{\circ}C$ and 9.8 mm/sec under the tap density, which were decreased with decreasing ZnO size and oxygen pressure. The final product had porous microstructure with spinel peaks in X-ray spectra. As the ZnO particle size in the reactant powders and oxygen pressure during the combustion reaction increase, coercive force, maximum magnetization, residual magnetization, squareness ratio were changed from 1324 Oe, 43.88 emu/g, 1.27 emu/g, 0.00034 emu/gOe, 37.8$^{\circ}C$ to 11.83 Oe, 68.87 emu/g, 1.23 emu/g, 0.00280 emu/gOe, 43.9 $^{\circ}C$ and 7.99 Oe, 75.84 emu/g, 0.791 emu/g, 0.001937 emu/gOe, 53.8 $^{\circ}C$ respectively. Considering the apparent activation energy changes with oxygen pressure, the combustion reaction significantly depended on initial oxygen pressure and ZnO particle size.

• Korean Journal of Agricultural Science
• /
• v.35 no.2
• /
• pp.137-145
• /
• 2008

A layer feeding trial was conducted to investigate the effects of high quality corn distiller's dried grains with solubles(DDGS) on laying performance and nutrient metabolizabilities. A total of 216 Hy-line Brown layers, 23-wk of age, were employed in a 10-wk feeding trial consisting of three dietary treatments(0%, 10%, and 20% DDGS), and six replicates per treatment. All experimental diets were prepared as iso-protein(17%) and iso-calorie(2,780 kcal/kg). At the end of the trial, the effect of DDGS on fecal ammonia emission was also estimated. The use of DDGS up to 20% in layer diets did not affect the feed intake, laying rate, egg weight, and feed conversion ratio(P>0.05). The DM metabolizability decreased significantly(P<0.05) by the DDGS supplementation(P<0.05). The NFE metabolizability decreased gradually as the level of DDGS increased(P<0.05). The fecal ammonia emission from DDGS-fed birds tended to decrease as the storage days extended. In conclusion, albeit DDGS has some unfavorable effects on DM and NFE metabolizabilities, it could be included in layer diets up to 20% level without any harmful effects on laying performance.

• Journal of the Korean Chemical Society
• /
• v.28 no.6
• /
• pp.403-411
• /
• 1984

Amberlite XAD-7 and XAD-4 resins impregnated with DXHQ (5,7-dihalo-8-hydroxyquinoline) were prepared for the adsorption, separation and recovery of heavy metal ions from aqueous solutions. The characteristics of the impregnated resins, DXHQ (X : Cl, Br, I)-XAD were studied to find out the proper pairs of resin and DXHQ for the adsorption of metal ions. The increasing order of the impregnated amount of DXHQ onto XAD-7 resin was as follows: DCHQ < DBHQ < DIHQ. It was observed from the plot of log $K_d$ vs. pH that the optimum pH range for the adsorption of DIHQ onto XAD-4 resin was from 3.0 to 7.0. The stabilities of the DXHQ-XAD resins were investigated by measuring the amount of DXHQ remained on the XAD resin after shaking the DXHQ-XAD resins in various solutions of pH ranging from 2 to 12 and hydrochloric acid solutions. The impregnated resins were considerably stable in both acidic and neutral solutions. The amount of DIHQ leached from DIHQ-XAD-4 resin by eluting with various HCl solutions (1 ∼ 5M) was negligible, but in the case of XAD-7 resin it increases as the concentration of HCl solution increases. The optimum pH ranges, absorption mole ratio (M : DXHQ) and adsorption capacities (mmol metal per gram of resin) for the adsorption of metal ions onto the DXHQ-XAD resins were determined respectively. The stability of metal ion absorbed by the DXHQ-XAD resins was observed as the following order: M-DCHQ-XAD-7 < M-DBHQ-XAD-7 < M-DIHQ-XAD-7. The adsorbed metal ions were quantitatively recovered by eluting with HCl (0.5 ∼ 5M) and DXHQ-XAD resins could be reused over 5 times without re-impregnation of DXHQ.

• Polymer(Korea)
• /
• v.33 no.4
• /
• pp.319-325
• /
• 2009

The solution polymerization was conducted to synthesize pressure sensitive adhesive for polarizer film using acrylic monomers. 2-Ethylhexylacrylate, butylacrylate, acrylic acid were used as acrylic monomers. The ratio was 2-ethylliexylacrylate:butylacrylate:acrylic acid=25:50:3.6 by reflecting $-40^{\circ}C$ of glass transition temperature in the pressure sensitive adhesive. When 1 wt% of coupling agent was added to the polymerized pressure sensitive adhesive, the light transmissivity was significantly increased. This result is due to the enhancement of adhesive power against liquid crystal cell by Si-O bond of coupling agents. Cross-linking agent was added by 0.5, 1.0, and 1.5 wt% with respect to the synthesized polymer. Initial tackiness decreased, while cohesion increased with increasing crosslinking agent. In the analysis of contact angle, the increase of crosslinking agents yielded the enhancement of surface energy, resulting in the decrease of contact angle. From the measurement of heat resistance, the acrylic pressure sensitive adhesive showed excellent heat resistance regardless of change in temperature and contents in crosslinking agent. In the observation of a cutting plane, the increased crosslinking agent represented a smoother and cleaner section. Comprehensively, the optimum additive amount of crosslinking agent was determined to be 1.0 wt% to monomer.

• Geophysics and Geophysical Exploration
• /
• v.17 no.2
• /
• pp.66-73
• /
• 2014

To estimate the shear-velocity ($v_s$) structure beneath the WIZ station on White Island in New Zealand, we applied receiver function (RF) inversion and H-${\kappa}$ stacking methods to 362 teleseismic events (Mw > 5.5) recorded during April 20, 2007 to September 6, 2013. Using 71 RFs with errors less than 20% after 200 iterative computations, we determined that the depth to Moho of $v_s$ = 4.35 km/s is $24{\pm}1km$ within a 15 km radius of the station. In an 1-d $v_s$ model derived by RF inversions, a 4-km thick low-velocity layer (LVL) at depths of 18 ~ 22 km was identified in the lower crust. This LVL, which is 0.15 km/s slower than the rocks above and below it, may indicate the presence of a deep magma reservoir. The H-${\kappa}$ stacking method yielded an estimate of the depth to the Moho of 24.5 km, which agrees well with the depth determined by RF inversions. The low $v_p/v_s$ ratio of 1.64 may be due to the presence of gas-filled rock or hot crystallizing magma.