• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.473-478
• /
• 2003

This paper presents static and dynamic measurement of the stress and motion characteristics for crawler type excavators. Eight scenarios were prepared for static measurement based on two extreme digging positions, maximum digging reach position and maximum digging force position. The measured items for static motion included stress, cylinder pressure, cylinder stroke and digging force. The measured static stresses showed that asymmetric digging force acting on a bucket induced higher stress level than symmetric one. The measured static pressures and digging forces also agreed with design pressures and design digging forces, respectively. The dynamic measurement was performed for two types of motion, that is, simple reciprocation of each cylinder and actual digging motion. The measured items for dynamic motion were stroke and pressure of each cylinder, stresses on the working device and acceleration on the upper plate of an arm. The measured data showed that the natural frequency of the excavator highly depended on the hydraulic stiffness of cylinders. Digging motion tests revealed that digging motion was closer to static motion rather than dynamic one.

• Tribology and Lubricants
• /
• v.17 no.3
• /
• pp.198-208
• /
• 2001

A Parametric study based on a computer analysis of the lubrication system of a four-cylinder gasoline engine is illustrated. Through the parametric study, the effects of various aeration levels on the change of oil flow rate and pressure are investigated. Also, at high oil temperature and low engine speed, the effect of oil aeration level on oil flow characteristics in lubrication system is investigated. The illustrated results may give to designers the guide lines of oil aeration level for the safe design of engine lubrication systems in terms of minimum pressure at crank oil bore.

• Journal of the Korean Society of Safety
• /
• v.26 no.2
• /
• pp.42-47
• /
• 2011

Going underwater is supposed to begin with the history of human beings. At first it was confined to relatively shallow level, less than several meters by holding breath. Recently, deep level diving has been necessary for such purpose as construction, maritime salvage, military operations, research and sports by using SCUBA(self-contained underwater breathing apparatus) equipment. As one goes down into water, the pressure on the diver is increased due to water pressure with depth, usually 1 atm for each 10 m water level. In deep water, mixed gas or nitrox(EAN, enriched air nitrox) could be applied for the divers lest they should get disease due to high pressure. Of these, the former is usually composed of oxygen and inert gas like helium or hydrogen, the latter contains higher oxygen content than that in normal air in which the oxygen concentration is designated by the character "EAN" followed by vol. % of oxygen, for example, "EAN 40" contains 40% of oxygen. In this case, a victim was found at the 39 m below the sea surface breathing air and nitrox in cylinder wrongly marked as EAN 36, which was analyzed to contain 63% of oxygen by GC/TCD. The cause of death could not be exactly related with the oxygen content in the nitrox cylinder, because the accurate depth for the victim to dive was not known, even though the victim was just found at the depth of 39 m. However, the wrongly marked nitrox could be believed to be the main cause of the death at the depth unless there happened any other accident except that during diving.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.5
• /
• pp.603-609
• /
• 1999

The effect of an external acoustic excitation on the wake structure behind a circular cylinder was experimentally investigated. The sound wave was excited in the frequency range of the shear layer instability and two sound pressure levels of 114 and 120dB were used in this study. As a result, the acoustic excitation modified the wake structure by increasing the velocity fluctuation energy without changing the vortex shedding frequency. The acoustic excitation enhanced the vortex shedding process and promoted the shear layer instability. Consequently, the acoustic excitation reduced the length of the vortex formation region and decreased the base pressure. In addition, the vortex strength of vortices was increased and the width of the wake was spread out due to the acoustic excitation. When the excitation frequency was identical to the shear layer instability frequency, the effect of the external flow control on the cylinder wake was maximized. In addition, with increasing the sound pressure level, the effect of the external acoustic excitation on the wake structure increased.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.5
• /
• pp.1649-1660
• /
• 1996

The flow around a circular cylinder was controlled by an acoustic excitation issued from a thin slit along the cylinder axis. The static pressure distributions around the cylinder wall and flow characteristics in the near wake have been measured. Experiments were performed under three cases of Reynolds number, 7.8 * 10$\^$4/, 2.3 * 10$\^$5/ and 3.8 * 10$\^$5/. The effects of excitation frequency, sound pressure level and the location of the slit were examined. Data indicate that the excitation frequency and the slit location are the key parameters for controlling the separated flow. At Re$\_$d/, = 7.8 * 10$\^$4/, the drag is reduced and the lift is generated to upward direction, however, at Re$\_$d/, =2.3 * 10$\^$5/ and 3.8 * 10$\_$5/, the drag is increased and lift is generated to downward direction inversely. It is thought that the lift switching phenomenon is due to the different separation point of upper surface and lower surface on circular cylinder with respect to the flow regime which depends on the Reynolds number. Vortex shedding frequencies are different at upper side and lower side. Time-averaged velocity field shows that mean velocity vector and the points of maximum intensities are inclined to downward direction at Re$\_$d/ = 7.8 * 10$\^$4/, but are inclined to upward direction at Re$\_$d/ = 2.3 * 10$\^$5/.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.74-80
• /
• 2005

It becomes necessary for engine manufactures to verify whether lots of engines on test bed during shop test are in compliance with NOx Technical Code for marine diesel engines more efficiently on the basis of engine group test concept which contains parent engine and member engines since all the engines are not needed to take NOx measurement. In addition, it becomes more obliged to consider parameters which affect NOx emission level and describe these parameters in NOx technical file as engine information and settings to define engine operation range with tolerance to make sure the engines are still in compliance with NOx emission limit on board after shop test. During preparation of engine group test for 4-stroke marine diesel engines, we evaluated NOx emission value under different engine operating conditions and found that there are certain parameters, for example, Charge air temperature and Max. cylinder pressure which have influence on NOx emission level. The NOx emission shall be satisfied with NOx technical code by means of controlling such parameters.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.255-260
• /
• 2004

Recently, the technologies related to the swash plate type oil hydraulic piston pump are requiring extreme technologies to overcome the limit of high efficiency in cope with high speed and pressure, and are devoted to compact the unit, to gain low noise level, and to adopt electronic technologies, and the question regarding to maximize the mechanical efficiency, that is, to minimize the torque loss by minimizing the leakage loss in the relative sliding region but these are in trade-off relation that tribological responding is very difficult. Cylinder block-valve pate in high speed relative sliding motion has the characteristics that should be extremely controlled for the optimization of these leakage loss and mechanical efficiency, and pressure resistance designing of them is important for high pressure performance. But, studies on the stress analysis of these parts have not been performed briskly, so in this paper the stress distribution and the region where the highest displacement appears are described through the static stress analysis using CATIA V5. Through the future studies on these theme, it has the purpose of finding the suitable materials for the other parts as well as cylinder block and valve plate, in cope with high pressure operation through the stress analysis with the most similar conditions for the practical operation.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1303-1308
• /
• 2008

In this study, we researched how to estimate life-stress relationship and acceleration factor through performing accelerated life test and analyzing it. The purpose of this study is to predict life of pneumatic cylinder within short time which is widely used in automation manufacturing line. In design of accelerated life test, we selected operating pressure and load that have the most influence on main failure mode of pneumatic cylinder as accelerated factor. We used two-way factorial design for arranging of test condition to accelerated factor and accelerated level.

• Transactions of the Korean hydrogen and new energy society
• /
• v.33 no.1
• /
• pp.67-76
• /
• 2022

We developed a technology that can measure the hydrogen uptake and diffusivity of rubber materials by using the volumetric analysis method and diffusivity analysis program through the measurement of the water level in the graduated cylinder. In this method, hydrogen gas is charged at a certain pressure for a certain period of time for a rubber material exposed to a high-pressure hydrogen gas environment, and then the pressure is reduced to measure the change in the water level in the graduated cylinder in real time, and based on the measured value, it is a technology that can evaluate hydrogen uptake and diffusivity using diffusivity analysis program. Using this method, the hydrogen uptake and diffusivity of the NBR material were measured with respect to the change in the type and weight ratio of the filler used to improve the physical properties of the rubber material. In addition, uncertainty analysis was performed on the diffusivity measurement method.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.148-156
• /
• 2000

For the in-line three cylinder engine whose crankshaft has a phase of 120 degrees, the total sum of unbalanced inertia forces occurring in each cylinder will be counterbalanced among three cylinders. However, parts of inertia forces generated at the No.1 and No.3 cylinders will cause a primary moment about the No.2 cylinder. In order to eliminate this out-of-balance moment, a single balance shaft has been attached to the cylinder block so that the engine durability and riding comfort may be further improved. Accordingly, the forced vibration analysis of the in-line three cylinder engine must be implemented to meet the required targets at an early design stage. In this paper, a method to reduce noise and vibration in the 800cc, in-line three cylinder LPG engine is suggested using the multibody dynamic simulation. The static and dynamic balances of the in-line three cylinder engine are investigated analytically. The multibody dynamic model of the in-line three cylinder engine is developed where the inertia properties of connecting rod, crankshaft, and balance shaft are extracted from their FE-models. The combustion pressure within the No.1 cylinder in three significant operating conditions(1500rpm-full load, 4000rpm-full load and 7000rpm-no load)is measured from the actual tests to excite the engine. The vibration velocities at three engine mounts with and without balance shaft are evaluated through the forced vibration analysis. Obviously, it is shown that the vibration of the in-line three cylinder engine with balance shaft is reduced to the acceptable level .