• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1254-1263
• /
• 1990

The temperature distribution and heat flux of the inner cylinder wall of a 4-cycle turbocharged gasoline engine were calculated by a 2-dimensional coordinate transformation. Boundary conditions of the inner wall of the cylinder were taken from the results of diagnostic engine simulations. Results show that the ununiformity of inner wall temperature of the cylinder black can be reduced by a proper choice of the thickness of fin and the distance between two cylinder blocks.

• Journal of the korean Society of Automotive Engineers
• /
• v.7 no.1
• /
• pp.55-62
• /
• 1985

This study modeled in axisymmetric solid elements and analyzed the neighbourhood of the contact surface zone between liner and block in a diesel engine. The results of finite element analysis show that this model is deformed by bolt jointed load and pressure load and that stresses can vary much due to major dimensional changes in the joint area. Guidelines have been developed for selecting fillet radii and for the width of the contact area between liner and block.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.602-607
• /
• 2007

The heavy duty diesel engine must have a large output for maintaining excellent mobility. The compacted graphite iron (CGI) is a material currently under study for the engine demanded for high torque, durability, stiffness and fatigue. In this study, three dimensional finite element model of a heavy-duty diesel engine was developed to conduct the stress analysis by using property of CGI. The FE model of the heavy duty diesel engine section consisting with four half cylinder was selected. The heavy duty diesel engine section include cylinder block, cylinder head, liner, bearing cap, bearing and bolt. The loading conditions of engine are pre-fit load, assembly force and gas force.

• Journal of Welding and Joining
• /
• v.17 no.6
• /
• pp.62-69
• /
• 1999

The advantages of Thermal sprayed coatings as a replacement for cast iron liners are reduced weight, better heat transfer and reduced cost. One of the most important performance attributes of a cylinder bore coating is its wear resistance, since it must survive the abrasive sliding of both the piston rings and the piston skirt. In this study, composite powders were prepared by ball milling of Al-13Si-3Mg(wt%) alloy with SiC particles. The concentrations of SiC were 40 and 60wt%. The composite powders were sprayed using Metco-9MB plasma torch. Plasma sprayed coatings were heat-treated at 500℃ for 3 hours. The wear resistances of the plasma sprayed coatings were found to improve with heat treatment and superior to the commercially available G.C.I.(gray cast iron). AlSiMg-40SiC heat-treated coatings showed the best wear resistance in this study.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.1 s.62
• /
• pp.8-13
• /
• 2005

In a multiple array of vertical cylinders, flaw patterns are very complex and very interactive between cylinders. The patterns are turbulent and non-linear depending on various factors. The gap and flow incoming velocity of upstream can affect on the downstream cylinder. In this study, the flaw characteristics around two vertical cylinders are investigated numerically and experimentally. As the gap between cylinders is changed at fixed coming velocity, the pressure distributions around cylinders are observed and compared by experimental and numerical approaches. The F.D.M and multi-block method are applied in the study. The pressures at 12 points around the cylinder are measured in the experiment. The results can be applied in the understanding and design of multiple pile array structures.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.20 no.5
• /
• pp.565-572
• /
• 2007

This paper addresses the kinematic study for the structural analysis of the S60ME-C multi-cylinder vessel engine. The load conditions such as the lateral force and the reaction force by the crank-shaft are required for the FEM analysis. The driving parts in vessel engine are assumed to be in frictionless rigid plane motion. We analytically derive dynamic forces for a single cylinder by using the dynamic force equilibrium. But, for the structural analysis for a single cylinder block, we use the loading conditions of two neighboring cylinders. Meanwhile, we use the single cylinder's loading condition to calculate the multi-cylinder's loading conditions, because each cylinder shows a cyclic loading pattern with respect to the crank arm's rotation angle.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.1043-1044
• /
• 2012

• The Journal of the Korean dental association
• /
• v.32 no.3 s.298
• /
• pp.211-214
• /
• 1994

90년에 접어들어, 임프란트보철물의 금속구조물을 완성하는데 있어서 단순한 wax-up에 의하기 보다는 Gold-cylinder(보철물과 연결되는 귀금속합금원통)주위에 resin으로 이는 resin-wing이라하여 일정한 두께의 Block을 붙여서 상품화하고 있다. 이를 사용하면 기공할때, 두께를 어느정도로 하여야 할까하는 신경을 쓸 필요없이 Resin-sing을 wax로 이어 주기만 하면 된다.

• Journal of Drive and Control
• /
• v.10 no.1
• /
• pp.56-60
• /
• 2013

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.321-325
• /
• 2000

Gasket of vehicle engine maintains airtight between cylinder head and engine block under high temperature and pressure, and plays important role in heat conduction of engine. And the characterization of the nonlinear behavior of metal gasket fer various bead shapes is very important as basic research for estimation of gasket durability. But it is very difficult to analyze the behavior of gasket In real experiment. In this paper, to analysis effects of the bead shape on the nonlinear behavior of cylinder head gasket under uniform pressure, the virtual experiment using the nonlinear finite element method was performed. Results are analyzed with residual deformation and the sealing pressure. With the increase of the height and the width of bead, the residual deformation and the sealing pressure increase. And if the height is very high and the width is very narrow, the wrinkles are occurred in the gasket while working.