• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.59-59
• /
• 2010

상변화 메모리 소자의 고집적화를 위한 새로운 패터닝 공정을 위하여 블락 공중합체의 자가 조립 특성을 적용한 고분자 패턴을 TiN기판 위에 적용화기 위한 연구를 진행하였다. 블락 공중합체의 자기 조립에 의한 패턴의 모양은 각 기판과 블락 공중합체간의 상호작용에 따라 sphere, cylinder, lamellar 형태의 모양을 띄게 된다. 표면처리가 안된 TiN기판 위의 PS-b-PMMA 블락 공중합체의 패턴의 형태는 cylinder와 lamellar 구조가 섞여 있는 구조로써 PS-r-PMMA 랜덤 공중합체로 기판 표면을 처리해 줄 경우 좀 더 균일한 cylinder 패턴 구조를 얻을 수 있었다. PS-r-PMMA로 기판 표면 처리 전 후의 상호 작용의 변화를 알아보기 위하여 물방울 접촉각 테스트를 하였으며 랜덤 공중합체와 블락 공중합체의 표면 처리 열처리 조건에 따른 패턴 행태의 변화를 관찰하기 위하여 모두 24,48,72시간으로 변화시켜 열처리 하였다. 최종 열처리 후 블락 공중합체의 패턴 형태의 주사 전자 현미경 관찰을 위하여 acetic acid에 60분 동안 침지시켜 PMMA를 제거 후 괄찰하였다.

• Journal of Mechanical Science and Technology
• /
• 제19권2호
• /
• pp.655-663
• /
• 2005

Tribological characteristics in the sliding parts of oil hydraulic piston pumps are very important in increasing overall efficiency. In this study, the fluid film between the valve plate and the cylinder block was measured by using a gap sensor and the mercury-cell slip ring unit under real working conditions. To investigate the effect of the valve shape, we designed three valve plates each having a different shape. One of the valve plates was without bearing pad, another valve plate had bearing pad and the last valve plate was a spherical valve plate. It was noted that these three valve plates observed different aspects of the fluid film characteristics between the cylinder block and the valve plate. The leakage flow rates and the shaft torque were also investigated in order to clarify the performance difference between these three types of valve plates. From the results of this study, we found that the spherical valve plate estimated good fluid film patterns and good performance more than the other valve plates in oil hydraulic axial piston pumps.

• 유공압시스템학회논문집
• /
• 제1권2호
• /
• pp.8-14
• /
• 2004

Abstract: In the oil hydraulic piston pumps the clearance between the valve plate and cylinder block plays an important role for volumetric and overall efficiency. Thus, adequate lubricational fluid film is needed for the interface. In this study, fluid film thickness is measured by a gap sensor and a slip ring under operational conditions to observe the behavior of the lubrication mechanism in detail. To investigate the effect according to the valve plate types in view of the fluid film, three different types were designed. Leakage flow rate and shaft torque were also measured to clarify the effect according to the valve plate types. A broad range of experiments were conducted to provide reasonable data on the effect of fluid film. In this experiments two main parameters were found, of which the one is the discharge pressure and the other is valve plate geometry. As a result, we found that the spherical valve plate could get more stable fluid film thickness, maintain good efficiency for high pressure range than the other types.

• KSTLE International Journal
• /
• 제8권2호
• /
• pp.29-34
• /
• 2007

Recently, requirements relating to performance, environment and noise in the oil hydraulic system of the heavy construction equipment have been reinforced continuously. In order to solve these technical trends, studies on the system compactness, operation under high pressure and great rotating speed, electronic control, substitute oil, and noise reduction have been progressed briskly. Among these recent studies, the system operation under high pressure is quite difficult to carry into effect due to mechanical limitations; that is, for realizing the system operation in the hydraulic pump under high pressure, the improvements or innovations on the design techniques, the manufacturing techniques, and the lubrication performance of the working oil are required. Accordingly, in this study, the stress distribution and optimum design factors under the maximum pressure were discussed by using stress analysis on the cylinder block of the hydraulic axial piston pump, which is one of the most important relative sliding regions.

• 한국산업융합학회 논문집
• /
• 제26권4_2호
• /
• pp.649-656
• /
• 2023

Recently, global warming has become severe, and regulation is established for carbon savings each field. its regulation is applied to various fields using IC engine such as automobile, ship, agricultural machine. Therefore engine block applied Common Rail Direct Injection(CRDI) technology, that carry out thermal-structure analysis to examine design. The thermal load about 900℃ by explosion was applied in cylinder. And pressure about 9 MPa(90 Bar) was applied to structure analysis. As a result, it was the highest at 185.99℃ at the top of cylinder. Static-structure analysis applied thermal load, that was shown maximum equivalent stress at 142.59 Mpa and Maximum principal stress 145.03 MPa, Minimum principal stress -149 MPa. When compare analysis results to material property, it design is safety structurally.

• Journal of Advanced Marine Engineering and Technology
• /
• 제21권3호
• /
• pp.267-277
• /
• 1997

In this paper, heat conduction characteristics of the cylinder block of a small 3 - cylinder, 4¬stroke gasoline engine were analyzed using the 3 - dimensional finite element method. Based on the experimental data, the engine cycle simulation was carried out in order to obtain the heat transfer coefficient and the temperature of the gas and the mean heat transfer coefficient of the coolant. Heat transfer data of the gas, which were averaged with respect to exposure time to the wall, were taken as convective boundary conditions corresponding to the operating conditions to obtain the temperature fields of the block. Finally silicon nitride(Si3N4) was taken as the material of the block liner in order to investigate its temperature distribution characteristics and compare the results with the original ones.

• 동력기계공학회지
• /
• 제6권1호
• /
• pp.20-26
• /
• 2002

The purpose of this study is preventing the stick, scuffing, scratch between piston and cylinder in advance, and obtaining data for duration test in actual engine operation. The temperature gradient in cylinder bore according to coolant temperature were measured using $1.5{\ell}$ class diesel engine. 20 thermocouples were installed 2mm deep inside from cylinder wall near top ring of piston in cylinder block, at which points major thermal loads exist. It is suggested as proper measurement points for engine design by industrial engineers. Under full load and $70^{\circ}$, $80^{\circ}C$ and $90^{\circ}C$ coolant temperature conditions, the temperature in cylinder block and engine oil increased gradually according to the increase of coolant temperature, the siamese side temperature of top dead center is $142^{\circ}C$ in peripheral distribution, that is about $20^{\circ}C$ higher than that at thrust, anti-thrust, and rear side temperature, respectively. The maximum pressure of combustion gas in $70^{\circ}C$ coolant temperature is about 2 bar lower than those of $80^{\circ}C$ and $90^{\circ}C$ coolant temperature. The engine torque in $80^{\circ}C$, $90^{\circ}C$ coolant temperature condition is about 4.9Nm higher than that of $70^{\circ}C$ coolant temperature.

• 한국자동차공학회논문집
• /
• 제6권3호
• /
• pp.1-10
• /
• 1998

In this paper, we investigated the improvement of characteristics of knock, emission and fuel consumption rate by optimizing the location and size of water transfer holes in cylinder head gasket without change of engine water jacket design itself. The cooling system was modified in the direction of reducing the metal temperature in the head and increasing the metal temperature in the block. The optimization of water transfer holes in cylinder head gasket was obtained by "flow visualization test". The water transfer holes were concentrated in front side of the engine in order to reduce thermal boundary layer in the water jacket of No. 2 and No. 3 combustion changer in the cylinder head, which would have a large knock intensity, and increase thermal boundary layer in the water jacket of the cylinder block. When the modified coolant flow pattern was applied as proposed in this paper, the knock characteristic was improved. The spark timing was advanced up to 2$^{\circ}$ in low and middle speed range at a full load. In addition, HC emission at MBT was reduced by 5.2%, and the fuel consumption rate was decreased up to 1% in the driving condition of 2400 rpm and 250 KPa. However, since this coolant flow pattern mentioned in this paper might deteriorate the performance of vehicle cooling system due to the coolant flow rate reduction, a properly optimized point should be obtained. obtained.

• 아동학회지
• /
• 제29권1호
• /
• pp.15-32
• /
• 2008

The logical and mathematical thinking of 1- to 3-year-olds was studied by age groups at 6 month intervals; logical-mathematical thinking was examined by the two physical knowledge activities of cylinder rolling and making a slope. Results showed that in their early 1st year infants failed in both tasks. Infants in their late 2nd year showed understanding of 'rolling things' and 'non-rolling things' by comparing cylinders and cubes in the cylinder rolling activity and they showed 'spatial inference' by adjusting the position and direction of the cylinder so that the cylinder could roll properly and by adjusting the board on a block in the slope making activity. Three-year-old children rolled a cylinder and made a slope without difficulty.

• 오토저널
• /
• 제13권6호
• /
• pp.57-64
• /
• 1991

Spart-ignition engine knock is an abnormal combustion phenomenon originated from auto- ignition of a portion of or the entire end-gas during the later stage of combustion process. And engine knock is accompanied by a vibration of engine cylinder block and a high-pitched metallic noise. Engine knock is characterized in terms of its intensity, its occurrence crank angel and the percentage of engine knock cycles. To characterize engine knock, a precise measurements of cylinder pressure and a statistical analysis of cylinder pressure data are needed. The purpose of this study is to develope a technique to measure engine knock and its characteristics as a function of ignition timing change. A 4-cylinder spark-ignition engine and unleaded gasoline, whose octane number was 94, were used for experiments. To measure engine knock and to analyze engine knock characteristics, cylinder pressure data were sampled by a high speed data acquisition system which was developed in this study. Cylinder pressure data were sampled at each 0.1.deg. crank angle and the number of cycles continuously sampled was 80.