• Korean Journal of Materials Research
• /
• v.23 no.12
• /
• pp.680-686
• /
• 2013

Tungsten oxide films were prepared by an electrochemical deposition method for use as the anode in rechargeable lithium batteries. Continuous potentiostatic deposition of the film led to numerous cracks of the deposits while pulsed deposition significantly suppressed crack generation and film delamination. In particular, a crack-free dense tungsten oxide film with a thickness of ca. 210 nm was successfully created by pulsed deposition. The thickness of tungsten oxide was linearly proportional to deposition time. Compositional and structural analyses revealed that the as-prepared deposit was amorphous tungsten oxide and the heat treatment transformed it into crystalline triclinic tungsten oxide. Both the as-prepared and heat-treated samples reacted reversibly with lithium as the anode for rechargeable lithium batteries. Typical peaks for the conversion processes of tungsten oxides were observed in cyclic voltammograms, and the reversibility of the heat-treated sample exceeded that of the as-prepared one. Consistently, the cycling stability of the heat-treated sample proved to be much better than that of the as-prepared one in a galvanostatic charge/discharge experiment. These results demonstrate the feasibility of using electrolytic tungsten oxide films as the anode in rechargeable lithium batteries. However, further works are still needed to make a dense film with higher thickness and improved cycling stability for its practical use.

• Korean Journal of Materials Research
• /
• v.8 no.6
• /
• pp.505-512
• /
• 1998

In this study, two-layer thermal barrier coatings composed of plasma sprayed 0.3mm $ZrO_2(8wt% Y_2o_3)$ ceramic coating layer and O.lmm $NiCrAlCoY_20_3$ bond coating layer on AISI 316 were investigated microstructure of the coating, oxidation of the metallic bond coating and adhesive strength to evaluate the durability of coating layer after cyclic and isothermal test at 90$0^{\circ}C$. And quantitative phase analysis of $ZrO_2(8wt% Y_2o_3)$ ceramic coating was performed as a function of thermal exposure time using XRD technique. The results showed that the amount of m - 2rO, phase in the coating was slightly increased with increasing thermal exposure time at 90$0^{\circ}C$. The c/a ratio of t' - $ZrO_2$ in the as-sprayed coating was 1.0099 and slightly increased to 1.0115 after 100 hours heat treatment. It was believed that $Y_2O_3$ in high yttria tetragonaJ(t') was transformed to low yttria tetragonaJ(t) by $Y_2O_3$ diffusion with increasing thermal exposure time. The adhesive strength was gradually decreased as thermal exposure time increased. After the isothermal test, the failure predominantly occured in ceramic coating layer. On the other hand. the specimens after cyclic thermal test were mostly failed at bond coating/ceramic coating interface. The failure was oeeured by decreasing the bond strength between bond coating and oxide scale which were formed by oxidation of the metallic elements within bond coating and by thermal stress due to thermal expansion mismatches between the oxide scale and ceramic coating.

• Journal of Animal Science and Technology
• /
• v.65 no.1
• /
• pp.113-131
• /
• 2023

The objective of this study was to investigate the effect of supplementing clay minerals and organic chromium in feed on broiler chicken under heat stress (HS). A total of 90 one-day-old broiler chicken (Arbor Acres) with an initial body weight of 45.0 ± 0.2 g were assigned to five treatment groups (six replications, three birds each cage): 1) NC group, basal diet under room temperature environment; 2) PC group, basal diet under high temperature (HT) environment; 3) ILT group, basal diet + 1% illite + HT; 4) ZLT group, basal diet + 1% zeolite + HT; 5) OC group, basal diet + 400 ppb/kg organic chromium + HT. The ILT and ZLT groups had significantly higher body weight than the PC group in 4 weeks. Apparent total tract digestibility of gross energy was increased in the ILT, ZLT, and OC groups compared to the PC group. The NC group had lower foot-pad dermatitis score than other groups. Escherichia coli population in the cecum and feces was decreased in the ZLT group than in the PC group. Lactobacillus in cecum and feces was significantly increased in the ZLT group than in the PC group. Regarding blood profiles, blood cortisol was decreased in the NC and ILT groups compared to the PC group. Water holding capacity and pH were increased in the ZLT group than the PC group. In conclusion, according to the results of growth performance, nutrients digestibility, bacteria counts, and meat characteristics, supplementation of the ZLT in broiler diet can alleviate HS.

• Restorative Dentistry and Endodontics
• /
• v.43 no.2
• /
• pp.25.1-25.10
• /
• 2018

Objectives: To evaluate the mechanical properties and metallurgical characteristics of the M3 Rotary and M3 Pro Gold files (United Dental). Materials and Methods: One hundred and sixty new M3 Rotary and M3 Pro Gold files (sizes 20/0.04 and 25/0.04) were used. Torque and angle of rotation at failure (n = 20) were measured according to ISO 3630-1. Cyclic fatigue resistance was tested by measuring the number of cycles to failure in an artificial stainless steel canal ($60^{\circ}$ angle of curvature and a 5-mm radius). The metallurgical characteristics were investigated by differential scanning calorimetry. Data were analyzed using analysis of variance and the Student-Newman-Keuls test. Results: Comparing the same size of the 2 different instruments, cyclic fatigue resistance was significantly higher in the M3 Pro Gold files than in the M3 Rotary files (p < 0.001). No significant difference was observed between the files in the maximum torque load, while a significantly higher angular rotation to fracture was observed for M3 Pro Gold (p < 0.05). In the DSC analysis, the M3 Pro Gold files showed one prominent peak on the heating curve and 2 prominent peaks on the cooling curve. In contrast, the M3 Rotary files showed 1 small peak on the heating curve and 1 small peak on the cooling curve. Conclusions: The M3 Pro Gold files showed greater flexibility and angular rotation than the M3 Rotary files, without decrement of their torque resistance. The superior flexibility of M3 Pro Gold files can be attributed to their martensite phase.

• Journal of Ocean Engineering and Technology
• /
• v.9 no.2
• /
• pp.141-148
• /
• 1995

Fatigue tests were carried out by a rotary bending testing machine of cantilever type. M.E.F.(ferrite encapsulated islands of martensite) materials were made by a series of heat treatment from a low carbon steel(SM 20 C). The fatigue tests were conducted at stress levels of 302 MPa and with frequencies of 25Hz, 2.5 Hz and 0.5 Hz in 3% NaCl solution. The fatigue strength increased with frequency got higher. The microcracks and corrosion pits were generated at the boundary between the matrix and the 2nd phase. The cracks generated by the corrosion pits were coalesced with the pits around the notch and became the initial crack. The $N_i/N_f$ ratio increased as the frequency and stress level decreased. The interference phenomenon increased with stress level and frequency gots higher. The crack propagation rate was delayed as the stress level lowers and the frequency gets higher, however, the range of the stress intensity factor depended only on a stress level.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.2
• /
• pp.81-86
• /
• 2014

The process parameter in optimized KOH alkali activation of soft carbon series coke material in high purity was set with DOE experiments design. The activated carbon was produced by performing the activation process based on the set process parameters. The specific surface area was measured and pore size was analyzed by $N_2$ absorption method for the produced activated carbon. The surface functional group was analyzed by Boehm method and metal impurities were analyzed by XRF method. The specific surface area was increased over 2,000 $m^2/g$ as the mixing ratio of activation agent increased. The micro pores in $5{\sim}15{\AA}$ and surface functional group under 0.4 meq/g were obtained. The contents of the metal impurity in activated carbon which is the factor for reducing the electrochemical characteristics was reduced less than 100 ppm through the cleansing process optimization. The electrochemical characteristics of activated carbon in 38.5 F/g and 26.6 F/cc were checked through the impedance measuring with cyclic voltammetry scan rate in 50~300 mV/s and frequency in 10 mHz ~100 kHz. The activated carbon was made in the optimized activation process conditions of activation time in 40 minutes, mixing ratio of activation agent in 4.5 : 1.0 and heat treatment temperature over $650^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.7
• /
• pp.627-633
• /
• 2002

Many isolated featureless domains were explicitly observed even at the air-water interface. We measured the surface pressure shift originating from the photo-isomerization of azobenzene units on the periphery of dendrimers. The maximum surface pressure was gradual1y increased and saturated by cyclic compression and decompression. By irradiation of 365 [nm] light, the surface pressure was increased, which was originated by the photo-isomerization process of the azobenzene group on the periphery from trans to cia form. The increase of the dipole moment ($\mu$), which may increase the interaction among Azo dendrimer molecules, made an important role on surface pressure shift. From the absorbance spectrum by UV irradiation and heat treatment, we can see that the absorbance in the UV region decreases with the increase of the UV irradiation time, but the peak at 350 m, characteristic of dendrimers in the LB monolayers, was not shifted until four irradiation cycles. This suggests that optical behavior and morphological change are affected by the functional group and the symmetric chain.

• The Korean Journal of Ceramics
• /
• v.5 no.4
• /
• pp.353-356
• /
• 1999

Highly proten-conductive elastic composites have been successfully prepared from $H_3PO_4$-doped silica gel and styrene-ethylene-butylene-styrene block elastic copolymer. In addition solid state electric double-layer capacitors have been fabricated using the composite as an electrolyte and activated carbon powders(ACP) hybridized with the composite as a polrizable electrode. The cyclic voltammogram of the electric double-layer capacitor fabricated demonstrated that electric charge was stored in the elecric double-layer at the interface between the polarizable electrode and the electrolyte. The value of capacitance of the capacitor was 10 F/(gram of total ACP), which was comparable to that of the capacitors using conventional liquid electrolytes.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.47.2-47.2
• /
• 2010

1980년대 이후로 등장한 Nd-Fe-B 소결자석은 뛰어난 자성특성을 나타내며, 원재료도 풍부하기 때문에 단위 자기 에너지당 가격은 비교적 저가이다. 따라서 대부분의 기존 Sm-Co와 주조 Al-Ni-Co 자석재료를 대체하며 다양한 첨단사업의 핵심소재로 적용되며, 자동차 및 의료기기 등 산업 전반에 사용되고 있다. 이러한 응용 중에서도 향후 녹색성장을 위한 신성장동력 산업인 하이브리드 자동차의 구동 모터로서 사용되는 대표적인 영구자석이다. 현재 개발된 Nd계 영구자석은 큐리온도가 낮고 높은 온도에서 자기적 성능의 열화가 심하게 진행된다는 단점이 있기 새로운 합금 설계 및 공정의 최적화를 통해 보자력을 향상 시킴으로써 사용온도를 $200^{\circ}C$ 정도로 높이는 연구가 활발히 진행되고 있다. 본 연구에서는 일반적인 제조공정을 통해 제조된 소결체의 미세구조에 변화시키기 위하여 약 $10^{-5}$ Torr의 진공분위기에서 $10^{\circ}C/min$의 승온/냉각속도로 $350^{\circ}C$부터 $450^{\circ}C$ 구간에서 2 사이클부터 8 사이클까지 승온과 냉각을 반복하는 열처리를 수행하였다. Nd-Fe-B 소결자석을 $350^{\circ}C{\sim}450^{\circ}C$ 온도구간에서 반복적인 열처리를 수행한 결과 열처리 사이클에 따라 보자력 특성이 다르게 나타내었다. 이에 승온과 냉각을 반복하며 나타난 미세구조의 변화가 자성특성에 어떠한 영향을 미쳤는지에 대해 고찰하였다.

• Journal of Welding and Joining
• /
• v.2 no.1
• /
• pp.41-48
• /
• 1984

Recrystallization technique was applied to analyze plastic strain at the notch tip of coarse grain HAZ in mild steel (SB 41) and high strength steel (SA 588). The notch tip of specimen was deformed by three point bending. Accumulated displacement (Crack Opening Displacement ${delta}t$) by the monotonic and cyclic loading under room temperature and hot strain embrittlement temperature ($250^{\circ}C$) was 0~1.0mm. Recrystallization heat treatment conditions were $650^{circ}C{ imes}3hr$ for SB 41 and $700^{circ}C{ imes}3hr$ for SA 588. The experimental results obtained were as follows ; 1) Distribution of the effective plastic strain at plastic zone was appeared by the function of crack opening displacement, and plastic zone or the effective plastic strain increased with crack opening displacement. 2) Plastic strain at notch tip of HAZ due to accumulated hot strain calculated as follows. .epsilon. over bar $_{p}$ = .epsilon. over bar $_{cr}$ (x/ $R_{x}$ ) $^{m}$ (m=0.25) 3) Work hardending ratio of notch tip for hot strain was linearly increased with .epsilon. over bar $_{max}$ and dependent upon the material types.s.