• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.2
• /
• pp.95-101
• /
• 2004

An experimental investigation was conducted to investigate the effects of the equivalence ratio and air mass flux on the combustion efficiency in a solid fuel ramjet used fuel grains which were highly loaded with boron carbide. Combustion efficiency increased with increasing equivalence ratio (grain length), and decreasing air mass flux. Higher inlet air temperature produced higher combustion efficiencies, apparently the result of enhanced combustion of the larger boron particles those burn in a diffusion controlled regime. Short grains which considered primarily of the recirculation region produced larger particles and lower combustion efficiencies. The result of the normalized combustion efficiency increased with inlet air temperatures coincident with the result of the Brayton cycle thermal and the total efficiency relating to the heat input.

• Journal of Ocean Engineering and Technology
• /
• v.3 no.2
• /
• pp.617-617
• /
• 1989

This paper deals with a fatigue life prediction of a surface crack based on the experimentally obtained relationship between surface crack length ratio $a/a_{f}$ and cycle ratio $N/N_{f}$ using micro computer. Firstly $a/a_{f}$-$N/N_{f}$ curves obtained from experimental tests, were assumed as three curves UC(the upper limit curve), LC(the lower limit curve) and MC(the middle curve), and these were utilized to predict the fatigue life. Comparing the calculated values which represent the characteristics of crack growth behaviors from the three assumed curves with the experimental ones, it has been found that in the stable crack growth region, they coincide reasonably well each other. And the differences between the fatigue lives obtained from the assumed curves and the experimental fatigue life did not exceed 20%. Using the characteristics of $a/a_{f}$-$N/N_{f}$ curves, it is possible to predict the da/dN-Kmax curves and the S-$N_{f}$ curves.

• Journal of Ocean Engineering and Technology
• /
• v.3 no.2
• /
• pp.108-117
• /
• 1989

This paper deals with a fatigue life prediction of a surface crack based on the experimentally obtained relationship between surface crack length ratio $a/a_{f}$ and cycle ratio $N/N_{f}$ using micro computer. Firstly $a/a_{f}$-$N/N_{f}$ curves obtained from experimental tests, were assumed as three curves UC(the upper limit curve), LC(the lower limit curve) and MC(the middle curve), and these were utilized to predict the fatigue life. Comparing the calculated values which represent the characteristics of crack growth behaviors from the three assumed curves with the experimental ones, it has been found that in the stable crack growth region, they coincide reasonably well each other. And the differences between the fatigue lives obtained from the assumed curves and the experimental fatigue life did not exceed 20%. Using the characteristics of $a/a_{f}$-$N/N_{f}$ curves, it is possible to predict the da/dN-Kmax curves and the S-$N_{f}$ curves.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.3 s.174
• /
• pp.634-644
• /
• 2000

Fatigue crack growth and life is estimated by various fracture mechanical parameters but affected by load, material and environment. Fatigue character of component without surface notch cannot be e valuated by above-mentioned parameters due to microstructure of in-service material. Single fracture mechanical parameter or nondestructive parameter cannot predict fatigue damage in arbitrary boundary condition but multiple fracture mechanical parameters or nondestructive parameters can Fatigue crack growth modelling with three point representation scheme uses this merit but has limit on real-time monitoring. Therefore, this study shows fatigue damage model using backpropagatior. neural networks on the basis of X-ray half breadth ratio B/$B_o$ fractal dimension $D_f$ and fracture mechanical parameters can predict fatigue crack growth rate da/dN and cycle ratioN/$N_f$ at the same time within engineering estimated mean error(5%).

• Geomechanics and Engineering
• /
• v.14 no.1
• /
• pp.1-8
• /
• 2018

This paper presents an investigation of the liquefaction characteristics and particle crushing of isotropically consolidated silica sand specimens at a wide range of confining pressures varying from 0.1 MPa to 5 MPa during undrained cyclic shearing. Different failure patterns of silica sand specimens subjected to undrained cyclic loading were seen at low and high pressures. The sudden change points with regard to the increasing double amplitude of axial strain with cycle number were identified, regardless of confining pressure. A higher cyclic stress ratio caused the specimen to liquefy at a relatively smaller cycle number, conversely producing a larger relative breakage $B_r$. The rise in confining pressure also resulted in the increasing relative breakage. At a specific cyclic stress ratio, the relative breakage and plastic work increased with the rise in the cyclic loading. Less particle crushing and plastic work consumption was observed for tests terminated after one cyclic loading. Majority of the particle crushing was produced and majority of the plastic work was consumed after the specimen passed through the phase transformation point and until reaching the failure state. The large amount of particle crushing resulted from the high-level strain induced by particle transformation and rotation.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.211-216
• /
• 2001

The components with the circular cross section have the symmetric combination parts for rotating balance and the crack emanates from the symmetric combination parts. The symmetric cracks from symmetric combination parts make a decrease in the component fatigue life more than single crack. In this study, to estimate the behavior of symmetric cracks, the fatigue test was performed using rotary bending tester on the specimen with a symmetric defects in circular cross section. The material used in this study is Ni-Cr-Mo steel alloy. Under the same stress, the result from the rotary bending fatigue test turned out that the symmetric cracks made a decrease in the fatigue life by 35% more than single crack and the relation between log a and cycle ratio $N/N_f$ obtained linearly.

• The KSFM Journal of Fluid Machinery
• /
• v.10 no.5
• /
• pp.9-19
• /
• 2007

Fluid temperature fluctuations in a mixing tee pipe were numerically analyzed by LES model in order to clarify internal turbulent flows and to develope an evaluation method for high-cycle thermal fatigue. Hot and cold water with an temperature difference $40^{\circ}C$ were supplied to the mixing tee. Fluid temperature fluctuations in a mixing tee pipe is analysed by using the computational fluid dynamics code, FLUENT, Temperature fluctuations of the fluid and pipe wall measured as the velocity ratio of the flow in the branch pipe to that in the main pipe was varied from 0.05 to 5.0. The power spectrum method was used to evaluate the heat transfer coefficient. The fluid temperature characteristics were dependent on the velocity ratio, rather than the absolute value of the flow velocity. Large fluid temperature fluctuations were occurred near the mixing tee, and the fluctuation temperature frequency was random. The ratios of the measured heat transfer coefficient to that evaluated by Dittus-Boelter's empirical equation were independent of the velocity ratio, The multiplier ratios were about from 4 to 6.

• Journal of Mechanical Science and Technology
• /
• v.19 no.7
• /
• pp.1393-1404
• /
• 2005

Fatigue crack growth and life have been estimated based on established empirical equations. In this paper, an alternative method using artificial neural network (ANN) -based model developed to predict fatigue damages simultaneously. To learn and generalize the ANN, fatigue crack growth rate and life data were built up using in-plane bending fatigue test results. Single fracture mechanical parameter or nondestructive parameter can't predict fatigue damage accurately but multiple fracture mechanical parameters or nondestructive parameters can. Existing fatigue damage modeling used this merit but limited real-time damage monitoring. Therefore, this study shows fatigue damage model using backpropagation neural networks on the basis of X -ray half breadth ratio B / $B_o$, fractal dimension $D_f$ and fracture mechanical parameters can estimate fatigue crack growth rate da/ dN and cycle ratio N / $N_f$ at the same time within engineering limit error ($5\%$).

• Fisheries and Aquatic Sciences
• /
• v.4 no.4
• /
• pp.208-218
• /
• 2001

We have investigated the gonad index (GI), gonadal development, reproductive cycle, first sexual maturity, sex ratio, the number of spawned eggs and spawning frequency of the Manila clam, Ruditapes philippinarum. Samples were collected from the intertidal zone of Komso Bay, Korea from January to December in 1999. Monthly changes in the gonad index (GI) and condition index showed a similar pattern in the reproductive cycle. The spawning period was once a year between early June and early October, there was a spawning peak between July and August when seawater temperature was over $20^{\circ}C$. The reproductive cycle of this species can be categorized into five successive stages; early active (February to March), late active (April to May), ripe (April to August), partially spawned (June to October), and spent/inactive stage (August to March). Percentages of first sexual maturity of female and male clams of l5.1-20.0mm in shell length were $56.3\%$ and $60.0\%$, respectively, and $100\%$ for the clams >25. mm. The sex ratio of individuals >15.1 mm in shell length was about 1:1 $(\chi^2= 0.02,\;p>0.05)$. Number of the eggs released from each clam by the induction increased as the size of clam in terms of shell length increased. Mean number of the eggs from the second induction of the spawning was $75.35-84.30\%$ $(average\;79.81\%)$ of the number of the eggs released in the first spawning. Our data indicated that R. philippinarum in Komso Bay has one major spawning peak with over two minor spawning, and the interval of each spawning was estimated to be approximately 15-17 (average 16.5) days.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.17 no.4
• /
• pp.129-143
• /
• 2014

The purpose of this study is to evaluate flooding vulnerability considering spatial characteristics focused on Changwon-si, Gyeongsangnam-do. Assessment Factors are water cycle area ratio, surface runoff, and precipitation. And construction of assessment factors and vulnerability was analyzed by GIS program. Water cycle ratio and surface runoff were vulnerable in urban area. Precipitation was often distributed in agriculture of the northern region. Results of flooding vulnerability were low in agriculture and forest of the northern region. In contrast, urban area was high because there has covered impervious land cover. Analytical results of flooding vulnerability density using hotspot spatial cluster analysis were high in urban area. And these areas were situated in down stream so flooding were generated. Therefore, flooding vulnerability assessment of this study can help for selecting construction sites of pervious land cover and rainwater management facilities in urban and environmental planning.