• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.781-785
• /
• 2005

Cutting forces and tool deflection in end milling are represented as the closed form of tool rotational angle and cutting conditions. The discrete cutting forces caused by tool entry and exit are continued using the Fourier series expansion. Tool deflection is predicted by direct integration of the distributed loads on cutting edges. Cutting conditions, tool geometry, run-outs and the stiffness of tool clamping pan are considered for cutting forces and tool deflection estimation. Compared to numerical methods, the presented method has advantages in short prediction time and the effects of feeding and run-outs on cutting forces and tool deflection can be analyzed quantitatively. This research can be effectively used in real time machining error estimation and cutting condition selection for error minimization since the ferm accuracy is easily predicted by tool deflect ion curve.

• Horticultural Science & Technology
• /
• 제30권1호
• /
• pp.13-20
• /
• 2012

This study was carried out to examine the effect of cutting condition on the growth of rooted cuttings and their subsequent growth of cut flower in plug cutting of Dendranthema grandiflorum 'Baekma'. The more leaves were attached to the cutting, the higher shoot growth of rooted cutting was observed. Cutting with two to six leaves was effective in shoot growth and rooting than any other treatment. Shoot growth of rooted cutting was not affected by cutting length, but rooting was better in 5 to 7 cm long cutting. Shoot growth and rooting of rooted cutting was promoted by increasing the cutting diameter, and rooting was better in 3.6-4.2 mm thick cutting than 3.1 mm thick cutting. As the treating concentration of NAA increased, shoot growth was inhibited and root length shortened in rooted cutting. Soaking with $100mg{\cdot}L^{-1}$ ${\alpha}$-naphtalene acetic acid (NAA) for 1 h was effective in shoot growth and rooting. Root growth such as root number, root length, and root weight was better in rooting medium mixed with 2:2 of peatmoss:perlite than the other treatments. When rooted cutting produced from cutting with four or six leaves was planted, better length, weight, and leaf number of cut flower was observed. In rooted cutting produced with 7-9 cm long cutting, growth of cut flower such as length, weight, and ray flower number was more effective than the others. Therefore, it is recommended that the 7 cm long and 3.6 mm thick cutting with four to six leaves is used to improve their rooting and subsequent growth of cut flower in plug cutting of Dendranthema grandiflorum 'Baekma'.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 한국공작기계학회 1995년도 추계학술대회 논문집
• /
• pp.30-36
• /
• 1995

This paper proposed on the effective cutting conditions of cage motor rotor by turning. If you want to introduce automatic manufacturing system into the cutting process of cage motor rotor, the selections of effective cutting conditions are necessary. The cutting process of cage motor rotor requires the precision and the out of roundness of cage motor rotor. The surface roughness of cutting face. it is very important factor with effect on the magnetic flux density of cage motor rotor. The purpose of this study is to find out the effects of cutting condition. upon adapting this results, we will improve the production rate in the cutting process of cage motor rotor. As a result, the selection of cutting conditions are important factors to production rate. And these are chosen by the investigations of cutting characters and surface roughness. The experimental result, showed that the increase of cutting speed caused the decrease of cutting force and the high surface integrity. The increase of feed rate and increase of depth of cut caused the increase of cutting force and surface roughness. Thus, the effective cutting conditions of cage motor rotor by turing are cutting speed 291m/min, feed rate 0.10mm/rev, depth of cut 0.05mm.

• Geomechanics and Engineering
• /
• 제29권3호
• /
• pp.359-368
• /
• 2022

Undercutting using an actuated disc cutter (ADC) involves more complex cutting mechanism than traditional rock cutting does, requiring the application of various new cutting parameters, such as eccentricity, cutter inclination angle, and axis rotational speed. This study presents cutting-edge laboratory-scale testing equipment that allows performing ADC tests. ADC tests were carried out on a concrete block with a specified strength of 20 MPa, using a variety of cutting settings that included penetration depth (p), eccentricity (e), and linear velocity (v). ADC, unlike pick and disc cutting, has a non-linear cutting path with a dynamic cutting direction, requiring the development of a new method for predicting cutting force and specific energy. The influence of cutting parameters to the cutter forces were discussed. The ratio of eccentricity to the penetration depth (e/p) was proposed to evaluate the optimal cutting condition. Specific energy varies with e/p ratio, and exhibits optimum values in particular cases. In general, actuated undercutting may potentially give a more efficient cutting than conventional pick and disc cutting by demonstrating reasonably lower specific energy in a comparable cutting environment.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.806-809
• /
• 2000

The factors which can improve tool life in machining are consisted of tool geometries, tool materials, coating methods. cutting environments, cutting conditions and so on. Cutting speed in cutting conditions is one of the important factors which can directly influence on the tool life. This paper deals the machinability which is concerned about the cutting direction and the tilt angle of fret form surface in hot die steel(STD I I). The NC datum were analysrd and the effective tool diameters were calculated according to the change of tilt angle the program which can continue the cutting speed with the change of spindle revolution is developed.

• Journal of the Korean Society for Precision Engineering
• /
• 제13권4호
• /
• pp.136-142
• /
• 1996

Automatic monitoring of cutting process is one of the most important technology in machining. AE sensing technology has been applied to monitoring process and proved to be effective in detecting tool abnor- malities such as tool wear and fracture. In this experimental study. AE signals were detected from the tool holder for continuous and interrupted cutting, which obtained from changing workpice material configuration, under control of constant cutting speed from CNC lathe. From statistical and frequency analysis, the AE signals were analyzed to obtaining the characteristics of continuous and interrupted cutting conditions and tool failure. The Kurtosis values decreased but RMS voltages increased as the cutting speed increased, in both continuous and interrupted cutting. RMS voltage is suddenly increased but Kurtosis value is suddenly decreased when tool failure condition. Power spectrum density of AE signals when tool failure reaches extreme value around 0.065 cycles/ .mu. m.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 한국공작기계학회 1995년도 추계학술대회 논문집
• /
• pp.37-43
• /
• 1995

The cutting process of cage motor rotor require high precision and good roughness, the surface roughness fo cutting face is very important factor with effect on the magnetic flux density of cage motor rotor. The paper describes a cause of decrease in the cutting force and roughness on low temperature cooling tool by means of analysis on the mechanism of force system at cutting condition and experimental findings. The main results as compared with the room temperature cutting are as follow : 1) The cutting resistance decreased due to low temperature cooling tool. 2) The surface roughness decreased due to low temperature cooling tool. 3) The low temperature cooling tool effected machinability of the cutting direction in machined surface. 4) The low temperature cooling decreased burr of corner in feed direction.

• Transactions of the Korean Society of Mechanical Engineers
• /
• 제18권2호
• /
• pp.292-301
• /
• 1994

The resultant cutting force during machining with a worn tool is viewed as a decomposition of the cutting force into a cutting force component related to chip removal from the workpiece and into a component dependent on the contact force between the tool flank's wear land and the workpiece. The shear line method, in which the cutting force is considered proportional to the length of the shear line, is used to calculate the cutting force component for the removal of the chip, while the elastic effect of the workmaterial on the tool is taken into consideration to analyze the effect of tool flank wear. The predicted resultant cutting force, expressed as the sum of both components, is compared to experimental data obtained during wave-on-wave cutting.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.526-530
• /
• 1996

In this paper, three different types of commercially tools-P20, NC123K and ceramic-have been used to working austempered ductile iron(ADI). In the austempered condition the materials are hard, strong and difficult to machine. Thus, we selected a optimum tool material among three different types of used tools in machining of austempered ductile iron. It was used acoustic emission(AE) to know cutting characteristic for selected tool and flank wear land of the ceramic too. The obtained results are as follows; (1) The ceramic tool among three different types of tools is the best in machining austempered ductile iron. (2) In case of ceramic tool, the amplitude level of AE signal(AErms) is mainly affected bycutting speed in cutting speed in cutting condition and it is proportioned to cutting speed. (3) There have the relationship of direct proportion between the amplitude level of AE signal and flank wear land of the tool. (4) If it find the value of AErms at each cutting speed, the in-process detection to ceramic tool's wear is possible

• Journal of the Korean Society for Precision Engineering
• /
• 제23권7호
• /
• pp.30-38
• /
• 2006

Laser cutting technology is one of flexible rapid manufacturing technologies with various advantageous including a high cutting speed, manufacturing of parts with a complex shape and others. The quality of the cut part and the optimum cutting conditions are highly dependent on the combination of the process parameters. The objective of this research works is to investigate the influence of process parameters, such as power of laser, cutting speed of laser and material thickness, on the surface roughness and the striation formation of the cut section for the case of cutting of CSP 1N sheet using high power Nd:YAG Laser with a continuous wave (CW). In order to find the relationship between process parameters and the surface roughness and the striation formation of the cut section, several experiments are carried out. Through the investigation of the empirical results, it has been shown that the surface roughness is highly related to the striation formation, including the frequency and angle of the striation, of the cut section. From the results of experiments, an optimum cutting speed for each cutting condition has been obtained to improve both the quality of the cut surface and the cutting efficiency.