• 터널과지하공간
• /
• 제21권3호
• /
• pp.151-163
• /
• 2011

LCM 시험은 디스크커터의 설계와 굴진성능 예측을 위한 가장 신뢰성 있는 시험으로 알려져 왔다. 하지만, 실대형 시료를 대상으로 실제의 커터 하중을 예측할 수 있는 이점이 있음에도 불구하고, 시료의 채취 및 운반이 용이하지 않고 1회 시험에 많은 비용이 소요된다는 단점을 갖고 있다. 또한 절리를 포함한 시료에 대한 시험의 경우, 시험 과정이 용이하지 않을 뿐만 아니라, 시험에서 예측된 모델을 설계에 반영하기 어려운 경우가 많다. 이러한 한계점을 극복하기 위해 수치해석 모델개발에 관한 연구가 활발히 진행되고 있다. 본 논문에서는 입자의 유동해석을 효과적으로 묘사할 수 있는 PFC2D를 이용하여 디스크커터의 절삭운동에 의한 암석시험편의 파쇄형상 및 균열 전파양상을 분석하고자 하였다. 또한 절리를 포함한 암석시험편을 모델링하여 절리의 경사각, 절리의 경사방향 그리고 절삭면에 노출된 절리의 간격의 변화에 따른 디스크커터의 절삭력을 수치해석적으로 분석하였다. 해석결과, 절리의 경사방향이 디스크커터의 진행방향과 반대일 때, 절리의 경사각이 작을수록, 노출된 절리의 간격이 좁을수록 더 큰 절삭력이 요구됨을 알 수 있었다. 이와 같은 수치해석 결과를 토대로, 디스크커터와 절리의 분포 특성과의 상관관계를 LCM 시험 결과와 비교 분석한다면, 보다 정확한 수치모델을 개발할 수 있을 것으로 판단되며 TBM(Tunnel Boring Machine) 굴착성능 예측 및 디스크커터의 적합 설계에 합리적인 판단기준을 제시할 수 있을 것으로 기대된다.

• 한국태양에너지학회 논문집
• /
• 제39권3호
• /
• pp.9-17
• /
• 2019

Laser cutting cell of solar cells can achieve high voltage and efficiency through more array than conventional 6 inch cell compared to same area. In this study, we fabricated c-Si cutting cell with various lasers and laser conditions such as power, speed, and number of times. In the case of picosecond laser, excellent surface characteristics were obtained due to small surface defects and low thermal damage at the output of 20W and the speed of 100 mm/s. However, it is not possible to fabricate a cutting cell having good characteristics due to nonuniform cutting inside the wafer when the processing for forming a cutting cell is not sufficiently performed. For nanosecond lasers, the best wafer characteristics were obtained for fabrication of excellent cutting cells at a frequency of 500 kHz and a laser speed of 100 mm/s. However, the nanosecond laser has not been processed sufficiently in the condition of a number of times. As a result, it was confirmed that the wafer thickness was cut by $63{\mu}m$ of the cell thickness of $170{\mu}m$ in the condition of five times of laser process. It was found that more than 30% of the wafer thickness had to be processed to fabricate the cutting cell. After cutting the 6-inch cell having the voltage of 0.65 V, we obtained the voltage of about 0.63 V.

• Journal of Electrical Engineering and Technology
• /
• 제7권4호
• /
• pp.576-581
• /
• 2012

A 23 W continuous wavelength $CO_2$ laser system exited by a high-frequency LCC resonant converter is adapted to cut a biodegradable rope fabricated with polybutylene succinate. As the biodegradable rope consists of three twisted strands, the thickness changes relative to the position of the laser beam and we thus propose a method to determine exact cutting depth. In order to obtain the parameters related to the rope cutting, the experimental and theoretical cutting depths are compared and analyzed for a range of laser heat sources. The melted thickness and groove width of the cut biodegradable rope are also examined. The proposed theoretical cutting depth depends on the incident power and target velocity ratio. From these experimental results, the biodegradable rope with a diameter of 22 mm can be cut with a heat source of 50 J/cm resulting in a melted thickness of 1.96 mm and a groove width of 0.65 mm. The laser system is shown to be perfect tool for the processing of biodegradable rope without the occurrence of raveling.

• 한국기계가공학회지
• /
• 제12권1호
• /
• pp.110-116
• /
• 2013

Curvic coupling of mill turret should maintain disk weight and the cutting resistance which occurs the machining operation and must also have power transmission function. In order to improve machining operation range, the ejecting distance from curvic coupling to the disk must increase as much as possible. But moment is increased by the lack of capacity of the curvic coupling. Increase of moment is the cause of vibration/noise and degradation of machining performance not only stability problem. The manufacturer of mill turret has no the design information between the ejecting distance and the cutting resistance with safety of curvic coupling. Therefore this study describes a finite element analysis model of mill turret using ANSYS workbench. The structural analyses and modal analyses with varying of the ejecting distances and cutting resistances are performed. Finally the equation for relationship between the critical ejecting distance and the cutting resistance is defined under 5 of the safety factor for the maximum von-Mises stress at the curvic coupling.

• 한국표면공학회지
• /
• 제43권1호
• /
• pp.41-45
• /
• 2010

The effect of $MoS_2$ and graphite content on wear resistance and mechanical properties of Cu/Sn bonded diamond micro blades was comparatively investigated in terms of volume and weight fraction. For the evaluation of endurance and cutting performance, instantaneous electric power consumption and cumulative wear loss during cutting glass work piece at constant velocity were measured with the micro blades of the wide range of lubricant content. The energy consumption of blades for glass cutting decreased with the content of lubricants. Wear amount of blade in volume increased with the amount of lubricant addition. It was found to be relevant to the decrease in flexural strength and hardness with the amount of lubricants. With the same amount of lubricant content in volume fraction $MoS_2$ showed superiority in mechanical properties and cutting performance than graphite while graphite could result in stronger effect on lowering electric consumption during cutting work piece for the same weight percent fraction than $MoS_2$ because of lower density.

• Nuclear Engineering and Technology
• /
• 제52권5호
• /
• pp.1043-1050
• /
• 2020

Radioactive aerosols are produced during the cutting of contaminated and activated metals. They must be collected and removed by a high-performing filtration system before releasing to the environment from the decommissioning workplace. The filtration system requires regular replacement to ensure the sufficient removal of radioactive aerosols because its filtration efficiency gradually decreases. This study evaluates the efficiency and lifetime of filters while cutting metals by using a plasma arc cutter. Particularly, this study considers the aerodynamic diameter distribution of number and mass concentrations for aerosols from 6 nm to 10 ㎛ when evaluating the performance of filters. After 20 time reuses for cutting operation performed in a cutting chamber, the removal efficiency is reduced from over 99 to below 93% at 2 ㎛. The results are used to analyze the lifetime of filters, the frequencies of their replacements, and impact on internal radiation dose.

• Journal of Biosystems Engineering
• /
• 제4권1호
• /
• pp.1-23
• /
• 1979

The use of barley seeder attached to rotary tiller in the rural area has a significant meaning not only for the solution of labor peak season, but also for the increase of land utilization efficiency. The facts that presently being used barley seeders are all based on the mechanical principles of the reverse rotation, center drive and are all using forward rotating tine, which is used to be easily and heavily worn out when it rotates reversely, raise problem of recommending them to rural area in Korea. Therefore, the main objective of the study was to develop new type of rotary tine attachable to barley seeders. To attain the objective the following approaches were applied. (1) The kinematic analysis of reverse rotating barley seeders. (2) The studies on the soil bin and artificial soil. (3) The comparative experiment on the power requirement of prototype tine. The results obtained from the studies are summarized as follow: 1. The kinematic analysis of barley seeder attached to rotary tiller: The following results were obtained from the kinematic analysis for deriving general formulae of the motion and velocity characterizing the rotary tine of barley seeders presently being used by farmers. a) The position vector (P) of edge point (P) in the rotary tine of reverse rotating, center drive was obtained by the following formula. $$P=(vt+Rcos wt)i+Rsin wt j+ \{ Rcos \theta r sin \alpha cos (wt- \beta +\theta r) +Rsin \theta r sin \alpha sin (wt-\beta + \theta r) \} lk $$ b) The velocity of edge point $(P^')$ of reverse rotating, center drive rotary tine was obtained by the following formula. $$(P^')=(V-wR sin wt)i+(w\cdot Rcoswt)j + \{ -w\cdot Rcos \theta r\cdot sin \alpha \cdot sin (wt-\beta +\theta r) + w\cdot Rsin \theta r\cdot sin \alpha \cdot cos (wt- \beta + \theta r \} k $$ c) In order to reduce the power requirement of rotary tine, the angle between holder and edge point was desired to be reduced. d) In order to reduce the power requirement, the edge point of rotary tine should be moved from the angle at the begining of cutting to center line of machine, and the additional cutting width should be also reduced. 2. The studies on the soil bin and artificial soil: In order to measure the power requirement of various cutting tines under the same physical condition of soil, the indoor experiments Viere conducted by filling soil bin with artificially made soil similar to the common paddy soil and the results were as follows: a) When the rolling frequencies$(x)$ of the artificial soil were increased, the densIty$(Y)$ was also increased as follows: $$y=1.073200 +0.070780x - 0.002263x^2 (g/cm^3)$$ b) The absolute hardness $(Y)$ of soil had following relationship with the rolling frequencies$(x)$ and were increased as the rolling frequencies were increased. $$Y=37.74 - \frac {0.64 + 0.17x-0. 0054x^2} {(3.36-0.17x + 0.0054x^2)^3} (kg/cm^3)$$ c) The density of soil had significant effect on the cohesion and angle of internal friction of soil. For instance, the soil with density of 1.6 to 1.75 had equivalent density of sandy loam soil with 29.5% of natural soil moisture content. d) The coefficient of kinetiic friction of iron plate on artificial soil was 0.31 to 0.41 and was comparable with that of the natural soil. e) When the pulling speed of soil bin was the 2nd forward speed of power tiller, the rpm of driving shaft of rotary was similar to that of power tiller, soil bin apparatus is indicating the good indoor tester. 3. The comparative experiment on the power requirement of prototype tine of reverse rotating rotary: According to the preliminary test of rotary tine developed with various degrees of angle between holder and edge pcint due to the kinematic analysis, comparative test between prototype rotary tine with $30 ^\circ $ and $10 ^\circ$ of it and presently being used rotary tine was carried out 2nd the results were as follows: a) The total cutting torque was low when the angle between holder and edge point was reduced. b) $\theta r$ (angle between holder and edge point) of rotary tine seemed to be one: of the factors maximizing the increase of torque. c) As the angle between holder and edge point ($\theta r$) of rotary tine was $30 ^\circ $ rather than $45 ^\circ $, the angle of rotation during cutting soil was reduced and the total cutting torque was accordingly reduced about 10%, and the reduction efficiency of total cutting torque was low when the angle between holder and edge point ($\theta r$) of rotary tine was $10 ^\circ $, which indicates that the proper angle between holder and edge point of rotary tine should be larger than $10 ^\circ $ and smaller than $30 ^\circ $ . From above results, it could be concluded that the use of the prototype rotary tine which reduced the angle between holder and edge point to $30 ^\circ $, insted of $45 ^\circ $, is disirable not only decreasing the power requirements, but also increasing the durabie hour of it. Also forward researches are needed, WIlich determine the optimum tilted angle of rotary brocket, and rearrangement of the rotary tine on the rotary boss.

• Restorative Dentistry and Endodontics
• /
• 제23권1호
• /
• pp.54-67
• /
• 1998

치근단 역충전 와동 형성을 위한 초음파 다이아몬드 기구의 임상적 적용의 타당성 및 특성을 평가하기 위해, 다이아몬드 기구의 상아질 삭제능력, 역충전 외동 형성효율 및 치질에 미치는 영향을 관찰하여 스테인레스 스틸 기구와 비교, 평가하였다. 치근단 역충전 와동 형성시 다이아몬드 기구와 스테인레스 스틸 기구를 발거된 소의 치아에서 노출시킨 상아질 표변에 일정한 출력과 시간 조건 하에서 작동시켜 상아질 표면으로부터의 삭제된 깊이를 측정하였다. 역충전 와동 형성효율을 평가하기 위하여 발거된 상악 제 1 대구치 치근에서 근관을 형성하고 gutta-percha로 충전한 다음 근단 3mm부위를 치아 장축에 직각되게 절제하고 초음파 기구의 와동형성 소요 시간 및 소요 stroke 수를 측정하였다. 초음파 기구를 이용한 와동 형성이 치질에 미치는 영향을 평가하기 위하여 초음파 와동 형성 전후의 치근단부 치질의 균열 발생빈도를 측정, 평가하여 다음과 같은 결과를 얻었다. $\cdot$ 저출력 또는 중출력에서 그리고 노출된 상아질에 수직 또는 수평으로 기구를 적용한 경우 모두에서, 다이아몬드 기구가 스테인레스 스틸 기구에 비해 높은 상아질 삭제효과를 나타내었다(p<0.01). $\cdot$ 초음파기구를 상아질 표면에 수직으로 적용한 경우에 출력이 높을수록 상아질 삭제효과가 우수하였으며, 수평으로 적용한 경우에는 출력에 따른 유의한 증가가 나타나지 않았다(p<0.01). $\cdot$ 중출력에서는 다이아몬드 기구가 스테인레스 스틸 기구에 비해 와동형시 소요되는 stroke 수와 시간으로 본 와동형성효율이 유의하게 우수하게 나타났다(p<0.05). $\cdot$ 저출력에서는 다이아몬드 기구가 스테인레스 스틸 기구에 비해 외동형성 후 치근단 균열 발생빈도가 유의하게 적게 나타났다(p<0.01).

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.988-991
• /
• 2001

Plastically deformed layer influences the mechanical property of the mechanical element such as creep hardening, microscopical crack and stress corrosion destruction. Therefore, the property so called the surface integrity has to be considered, and the machined surface including plastic deformation, distribution of stress has to be conducted quantitatively. This paper explains the orthogonal cutting, and made an orthogonal cutting model using the finite element method, then analyzed cutting power, plastic deformation of workpiece. It introduces the developed subsequent recrystallizations technique for measurement of the plastic strain of machined surface, and verified the technique.

• 한국기계가공학회지
• /
• 제2권3호
• /
• pp.69-75
• /
• 2003

Plastically deformed layer influences the mechanical property of the mechanical element such as creep hardening, microscopical crack and stress corrosion destruction. Therefore, the property so called the surface integrity has to be considered, and the machined surface including plastic deformation, distribution of stress has to be conducted quantitatively. This paper explains the orthogonal cutting, and made an orthogonal cutting model using the finite element method, then analyzed cutting power, plastic deformation of workpiece. It introduces the developed subsequent recrystallizations technique for measurement of the plastic strain of machined surface, and verified the technique.