• 한국정밀공학회지
• /
• 제12권11호
• /
• pp.63-73
• /
• 1995

A mechanistic force system model considering the flank wear for the face milling process has been developed. The model predicts variation of the cutting forces according to flank wear in face milling over a range of cutting conditions, cutter geometries and cutting process geometries including relative positions of cutter to workpiece and rounouts. Flycutting and multitoth cutting teste were conducted on SS41 mild steel with sintered carbide tool. In order to verify the mechanistic force model considering the flank wear of cutting tools, a series of experiments was performed with single and multitooth cutters in various cutting conditions. The results show good agreement between the predicted and measured cutting force profiles and magnitudes in time and frequency domains.

• 한국안전학회지
• /
• 제16권3호
• /
• pp.135-142
• /
• 2001

본 연구에서는 복합소재인 GFRP(Glass Fiber Reinforced Polyester)의 2차원 절삭공정에서 주파수 스팩트럼과 절삭 메커니즘과의 연관성에 관하여 논의한다. 해석방법으로는, 공정중 발생하는 절삭력 신호를 FFT에 의해 주파수 분석하고 주파수 스팩트럼과 다양한 칩형성 메커니즘과의 연관관계를 모델링한다. 특히, 섬유경사각(Fiber orientation angle), 절삭변수 그리고 공구형상이 절삭 메커니즘에 미치는 영향을 평가하였다.

• 한국공작기계학회논문집
• /
• 제14권5호
• /
• pp.7-12
• /
• 2005

This paper presents several time series methods to analyze the chatter mechanics by using the power spectrum of these algorithms considering the cutting dynamics. In this study, several time series models such as AR(burg, forwardbackward, geometric lattice, instrument variable, least square, Yule Walker), ARX(1s, iv4), ARMAX, ARMA, Box Jenkins, Output Error were modeled and compared with one another. Finally, it was proven that time series modelings are also a desirable and reliable algorithm than the other conventional methods(FFT) for the calculation of the chatter mode in turning operation. Also, the spectrum of times series methods is a little bit more powerful than the FFT fer the detection of a high noisy and weak chatter mode. The radial cutting force Fy has been used for spectrum and chatter stability lobe analysis in this study.

• 한국정밀공학회지
• /
• 제11권1호
• /
• pp.44-53
• /
• 1994

We experimented on cutting characteristics-cutting force, behavior of cutting temprature, surface foughness, behavior of chips-under low tempdeature, which generated by liquid nitrogen (77K). The workpieces were freezed to -195 .deg. C and liquid nitrogen was also sprinkled on cutting area in order to increase the efficiency of machining in low temperature. The workpiece was became to -195 .deg. C in 5 minutes, and cutting temperature in CC was lower about 170 .deg. C than NC. The cutting force trended to increase slighty in cooled cutting, but chip thickness was decreased, shear angle was however increased. The form of chips was in good conditions of long or short tubular chips in CC. In CC surface roughness of workpiece was better than NC. In NC surface hardness of chips trended to increase according to increasing of cutting speed, but in CC it trended to decrease. The power spectrum of vertical cutting force trended to increase according to increasing of feed, and in CC it was higher than NC.

• 한국정밀공학회지
• /
• 제16권9호
• /
• pp.62-67
• /
• 1999

In milling, cutting tool ins directly attached to spindle and this tells that spindle can provide very useful information on the cutting tool condition such as wear or breakage. Since spindle is rotating at a high speed, measuring spindle velocity using a noncontacting measurement system gives the best information which can be obtained. Due to the force applied to spindle through cutting tool, velocity of spindle changes. And any change in cutting tool condition affects cutting force and consequently spindle vibration. With the intent of continuously monitoring cutting tool condition in intermittent machining operations in a benign manner, a noncontacting velocity measurement system using a laser Doppler velocimeter was assembled to measure spindle torsional vibration. Spindle vibration was measured and analysis of it in the frequency domain yielded a measure which corresponded to amount of cutting tool wear in milling.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.842-846
• /
• 1997

Micro-hole drilling (holes less than 0.5 mm in diameter with aspect ratios larger than 10) is gaining increased attention in a wide spectrum of precision production industries. Alternative methods such as EDM, laser drilling, etc. can sometimes replace mechanical micro-hole drilling but are not acceptable in PCB manufacture because they yield inferior hole quality and accuracy. The major difficulties in micro-hold drilling are related to wandering motions during the inlet stage, high aspect ratios, high temperature,etc. However, of all the difficulties, the most undesirable one is the increase of drilling force as the drill penetrates deeper into hold. This is caused mainly by chip related effects. Peck-drilling is thus widely used for deep hole drilling despite the fact that it leads to low productivity. Therefore, in this paper, a method of cutting force regulation is proposed to achieve continuous drilling. A proportional plus derivative (PD) and a sliding modecontrol algorithm will be implemented for controlling the spinle rotational frequeency. Experimental results will show that sliding mode control reduces the nominal cutting force and its variation better than the PD control, resulting in a number of advantages such as an increase in drill life, fast stabilization of the wandering motion, and precise positioning of the hole.

• 한국정밀공학회지
• /
• 제15권1호
• /
• pp.117-129
• /
• 1998

Micro-hole drilling (holes less than 0.5 mm in diameter with aspect ratio larger than 10) is recently having more attention in a wide spectrum of precision production industries. Alternative methods such as EDM. laser drilling, etc. can sometimes replace the mechanical micro-hole drilling but are not acceptable in PCB manufacture because of the inferior hole quality and accuracy. The major difficulties in micro-hole drilling are related to small signal to noise ratios, wandering motions of the inlet stage, high aspect ratios, high temperatures and so forth. Of all the difficulties. the most undesirable one is the increase of drilling force as the drill proceeds deeper into the hole. This is caused mainly from the chip effects. Peck-drilling is thus widely used for deep hole drilling despite that it suffers from low productivity. In the paper, a method of cutting force regulation is proposed to achieve continuous drilling. A PD and a sliding mode control algorithms were implemented through controlling the spindle rotating frequency. Experimental results show that the sliding mode control reduces the nominal cutting force and the variation of the cutting force better than the PD control. The advantages of the regulation, such as increase of drill life, fast stabilization of a wandering motion, and the precise positioning of the hole are verified in experiment.

• 한국산업안전학회:학술대회논문집
• /
• 한국안전학회 2000년도 춘계 학술논문발표회 논문집
• /
• pp.52-57
• /
• 2000

This paper discusses frequency analysis based on frequency spectrum in orthogonal cutting of fiber-matrix composite materials. A glass reinforced polyester (GFRP) was used as workpiece. Analysis method employs a force sensor and the signals from the sensor are processed using a fast Fourier transform (FFT) technique. The experimental correlation between the different chip formation mechanisms and model coefficients are then established. (omitted)

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.617-618
• /
• 2007

• 한국기계가공학회지
• /
• 제5권2호
• /
• pp.16-21
• /
• 2006

In this study, the analytic realization of chatter mechanism using radial basis neural network(RBNN) was introduced and compared with the conventional stability analysis. In this regard, the FFT and time series spectrum analysis was used as a criterion for the existence of chatter in end-milling force. The desired coded outputs of chatter was trained and finally converged to desired outputs. The output of the RBNN match well with the conventional desired stability lobe. Using this trained data, the stability boundary of the radial basis neural network was acquired using the contour plotting. As a result, the proposed stability lobe boundary using RBNN consists well with the conventional analytical boundary that is calculated in characteristic equation of transfer function in chatter dynamics. In this RBNN analysis, two input and three output parameters were used in this paper.