• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.581-584
• /
• 2003

The austenitic STS 304 stainless steel was turned to clarify the effects of tool geometry on the tool wear. The wear of TiN-TiCN-TiC-TiAlN coated tungsten carbide tool was the smallest, exhibiting larger wear in the order of Si-Al-O-N ceramic, TiN coated tungsten carbide, TiN-TiCN-TiN coated tungsten carbide, TiC-TiN cermet and M20 tungsten carbide tools at the same cutting conditions. The S-type tool of M20 with large approach angle showed the longest tool life of all tools used in this tests due to preventing the groove wear of the side cutting edge. The wear of the S-type tool with the rake angle of 15$^{\circ}$became smaller than with that of -5$^{\circ}$, but the tool with the nose radius of 0.8mm did not perform much better with increasing the rake angle.

• Design & Manufacturing
• /
• 제10권3호
• /
• pp.34-38
• /
• 2016

Roll forming is a continuous production process that is mass-produced. The roll forming process is produced in various forms. The special feature of roll forming is a continuous production. Therefore, the process of cutting the material is essential. The troubles in a shearing process affects the low productivity. Accordingly, it is important to reduce the factors that inhibit the material flow. And it is difficult to apply the common shear angle. Because it is not a simple forms, such as a progressive die. This study shows how to select the angle of a shear punch and the shape of a cutting punch in the product with a specific shape. Conclusively through three different model, it is advantageous to apply the different shear angle and clearance along the forms.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.19-22
• /
• 2004

Shearing including punching, blanking, trimming, slitting, etc is one of the most frequently used processes in sheet metal manufacturing. It has been widely using for manufacturing autobody, electronic components, aircraftbody, etc. In this paper, it has been researched by the experimental investigation to examine the influence of shearing processes parameters such as clearance, cutting angle, material properties, etc. From the results of experiment, it has shown that it gives the small variations at burr height below the proper clearance and it also presents that it is no affected the variations of cutting angle.

• 한국정밀공학회지
• /
• 제13권8호
• /
• pp.139-145
• /
• 1996

Tapping is one of the most widely used machining operations. There are several methodes of producing external screw threads, e.g. turning, milling with single or multiple cutter, rolling, and grinding, but the methods available for cutting enternal threads are less numerous, and for threads in small holes, tapping is employed almost exclusively. In this study, the tap with the various geometry has been developed in order to tap special workmaterial at considerably higher cutting speed than that of the conventional HSS tap. The experimental tests are run with various cutting speed by using a piezo type tool dynamometer to measure tapping torque. Tapping torque is affected by the design of the tap, which seems to be due to internal friction and shearing of the metal. It is clarified that the process of chip formation strongly depends on rake angle, relief angle, angle of twist.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.259-260
• /
• 2013

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.107-113
• /
• 1996

This paper presents the experimental results on the cutting performance and wear characteristics of CBN ball end-mill. The influence of cutting fluids and rake angles on the tool performance is reported. It i found that the neat cutting oil is beneficial to obtain good surface roughness and 30 .deg. of rake angle gives the minimum tool wear. The microscopic investigations reveal that the coated carbide endmills wear by fracture whereas the CBN endimills wear by attritious mode.

• Journal of Biosystems Engineering
• /
• 제26권6호
• /
• pp.563-570
• /
• 2001

To develop a stalk detaching system the effect of shape factor of red pepper affecting the performance of unfolding, arranging and cutting was analysed. The obtained results are as follows : By cutting experiment, it was found that the bending of stalk affected the cutting rate of stalk, and that the bending of body increased the amount of peppers that were expelled from the cutting guide by conveying brush. The ratios, 'bending length of a body/body length'and 'bending length of a stalk/stalk length', could be used as criteria far abnormality of body and stalk of peppers, respectively. As a result of experiment, it was concluded that mechanical treatment would be difficult for the peppers with indexes greater than 0.4 and 0.3 fur body bending and stack bending. respectively. So, these indexes were used as criteria for distinguishing abnormality from normality of peppers. In the unfolding unit, conveyance of peppers was impossible for both of normal and abnormal ones at the inclination angle of 10°, especially, at the frequency of 8.3 Hz peppers maintained stationary state. At the inclination angle of 20°, both of normal and abnormal peppers showed similar tendencies, but abnormal ones showed an accumulation trend gradually with increased feeding speed. In the arranging unit, conveyance of peppers was almost impossible for both of normal and abnormal ones at the inclination angle of 20°, showing almost no difference between the conveyances of normal and abnormal ones. In the case of the inclination angle of 30°, at the condition of the feeding speeds and frequency corresponding 0.06 m/s, 0.08 m/s and 8.3 Hz, respectively, the passing time of the abnormal peppers on the arranging plate increased rapidly.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.105-110
• /
• 2004

This paper deals with the study of feasibility of rotary carbide tools in the machining of aluminium alloy. A rotary tool holder was designed and manufactured for this work. Experiments were performed using Taguchi methods and regression analysis to analyse the influence of various factors and their interactions on the cutting characteristics of rotary carbide tools during machining. The cutting force is influenced the most featly at the inclination angle. The surface roughness is influenced distinctly at depth of cut. It deduced an equation to predict cutting force and surface roughness. Hence, it could be concluded here that the proposed model agrees with the experimental data satisfactorily.

• 한국정밀공학회지
• /
• 제33권6호
• /
• pp.447-452
• /
• 2016

The simulation of Carbon fiber reinforced polymer (CFRP) machining facilitates the selection of optimal cutting parameter for high machining efficiency and better surface quality. In this study, This paper proposes a dual-dexel model to represent the fiber laminate with computational geometry method to calculate the fiber length removed per revolution and fiber cutting angles. A flat end milling simulation software is developed in C# to simulate and display the CFRP milling process. During simulation, fiber lengths, fiber cutting angle and engaged cutting angle can be displayed in real-time. A CFRP plate with different angles in different layer is used to compare the simulation results.

• 한국정밀공학회지
• /
• 제16권12호
• /
• pp.71-77
• /
• 1999

In this study, Cu ferrite was machined with cermet tool to clarify the machinability. The main conclusions obtained were as follows. The tool wear becomes the smallest at the cutting speed of 90m/min with the depth of cut of 0.2mm. The surface roughness becomes larger with increasing the cutting speed and the chamfer angle. The tool with the chamfer angle of $15{\circ}$ shows the best performance. The surface roughness increases almost proportionally with the increase of the chip size. The tool wear decreases with increasing feed in the depth of cut not more than 0.2mm.