• 한국생산제조학회지
• /
• 제20권6호
• /
• pp.714-719
• /
• 2011

The surface roughness depending on the machining method is very important because is produce a finished product through riveting, sealing, bonding, and special paint in order to curb the turbulence and air resistance which occur between the sheets. Aluminum alloy 2024 which is widely used for interior and exterior material of aircraft are tested. Jin-young JW-60C wire cutting machine was used in this experiment. In this paper, the experimental investigation has been performed to find out the influence of the surface roughness and surface shape characteristics on the wire-cut EDM of discharge energy in aluminium alloy 2024. The selected experimental parameters are peak current, no-load voltage, off time and feed rate. The experimental results give the guideline for selecting reasonable machining parameters. The high discharge energy on the idle time, almost no change in surface roughness can be seen.

• 한국산학기술학회논문지
• /
• 제18권9호
• /
• pp.61-67
• /
• 2017

프레스금형 제작 시 사용목적에 맞는 적합한 소재선택과 빠른 가공방법에 대한 연구는 금형제작시간을 줄이고 금형원가를 절감하는데 절대적으로 필요한 연구분야이다. 특히 장수명 프레스금형을 개발하기 위해선 열에 대한 고찰이 반드시 이루어져야 한다. 일반적으로 프레스금형의 주요부품 소재로는 Cr, W계 저합금 공구강, 고탄소 고크롬강, 고속도강 등 냉간 금형용 합금공구강이 많이 쓰이고 있다. 프레스금형부품을 가공하는 데는 주로 공작기계와 와이어 컷 방전가공을 사용하고 있다. 가공공정에 따라 금형부품의 가공시간 및 수명이 많은 차이가 난다. 밀링가공과 연삭가공으로 제작된 부품의 경우 제작시간과 비용은 많이 드는데 비해 금형의 수명이 길고 밀링가공과 와이어 컷 방전가공을 사용하면 제작시간과 비용은 절감되는 반면 금형수명은 줄어드는 현상이 나타난다. 따라서 본 연구에선 가공시간과 비용이 절감되는 가공방법으로 열처리를 사용하여 금형의 사용수명을 향상시키는 방법에 대해 고찰하고자 한다. 밀링가공-연삭가공, 밀링가공-와이어 컷 방전가공, 밀링가공-와이어 컷-고온템퍼링, 3가지 가공방법으로 시편을 제작하여 가공표면과 중심부를 SEM, EDS분석 및 표면조도분석으로 문제점을 고찰하였고 밀링가공-와이어 컷 방전가공-고온템퍼링의 가공방법으로 밀링가공-연삭가공과 동일한 금형의 수명을 만드는 방법을 도출하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.64-70
• /
• 2001

This work deals with the electrical conductivity of dielectric and cobalt percentage on output parameters such as metal removal rate and surface roughness value of sintered carbides cut by wire-electrical discharge machining (W-EDM). To obtain a precise workpiece with good quality, some extra repetitive finish cuts along the rough cutting contour are necessary. Experimental results show that increases of cobalt amount in carbides affects the metal removal rate and worsens the surface quality as a greater quantity of solidified metal deposits on the eroded surface. Lower electrical conductivity of the dielectric results in a higher metal removal rate as the gap between wire electrode and workpiece reduced. Especially, the surface characteristics of rough-cut workpiece and wire electrode were analyzed too. To obtain a good surface equality without cracks, 4 finish-cuts were necessary by reducing the electrical energy and the offset value.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.930-933
• /
• 2001

Titanium Alloys used in this experiment has an good corrosion resistance and specific strength, and is the new material developed for medical supplies living goods. In this study the rolled titanium alloy is done by annealing, solution heat-treatment and aging and then is worked by wire EDM. With changing the process conditions, the process properties of surface hardness, surface roughness, shape of process surface and the analysis of ingredients are measured through experiment repeating main cut and finish cut. It is confirmed to gain good measure values as increasing the number of processing of wire EDM. In this experiment the phenomena of processing is studied and the appropriate process condition is proposed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.956-959
• /
• 2001

In die and mould industry, major material such as cemented carbide is broadly used for increasing the life time and decreasing the cost. It is also required the development for the skills of wire-cut electrical discharge machining(WEDM), but the WEDMed surface was found to be worst due to the attached components of wire. Precision machining method like lapping is necessary for obtaining high quality surface. The lapping compound such as Al2O3 and SiC and cast iron lap can be used for lapping process. The components of Cu and Zn were found WEDMed surface of the specimen. As the result, the low quality of precision was obtained and the heat damage layer of the specimen was occurred. The value of surface hardness was deteriorated, and therefore finish process was required.

• Journal of Mechanical Science and Technology
• /
• 제15권12호
• /
• pp.1676-1682
• /
• 2001

This work deals with the electrical conductivity of dielectric and cobalts percentage on output parameters such as metal removal rate and surface roughness value of sintered carbides cut by wire-electrical discharge machining (WEDM). To obtain a precise workpiece with good quality, some extra repetitive finish cuts along the rough cutting contour are necessary, Experimental results show that increases of cobalt amount in carbides affects the metal removal rate and worsens the surface quality as a greater quantity of solidified metal deposits on the eroded surface. Lower electrical conductivity of the dielectric results in a higher metal removal rare as the gap between wire electrode and workpiece reduced. Especially, the surface characteristics of rough-cut workpiece and wire electrode were analyzed too. To obtain a good surface equality without crack, 4 finish-cuts were necessary reducing fille electrical energy and the offset value.

• 한국터널지하공간학회 논문집
• /
• 제17권6호
• /
• pp.615-621
• /
• 2015

In this paper diamond wire cutting method has been proposed to cut the rock in the tunnel face. Diamond wire saw method could cut the rock from tunnel face with very minor vibration and noise. In this study rock cutting process has been simulated with FEM method by using LS-DYNA explicit non-linear finite element code. Normal load act as an prime factor when cutting the rock surface. For observing the effect of normal load on bead, several experiments has been conducted by varying normal loads on the bead. From each experiment, cutting rate has been calculated to compare the cutting rate with different load conditions. By increasing the normal load on bead, cutting rate increases drastically.

• 한국기계가공학회지
• /
• 제4권3호
• /
• pp.5-12
• /
• 2005

In wire discharge machining which is using STD 11 as die materials, the major factors of machining speed are discharge voltage, discharge current, and discharge time. All of the three factors give the effect. Increasing of the discharge pulse time gets groove width wider and it relatively increases surface roughness and clearance. If no load voltage is decreased, surface roughness is good but it decreases machining speed. If on time is increased, machining speed will get faster and clearance and offset value also get bigger.

• 화약ㆍ발파
• /
• 제36권4호
• /
• pp.16-25
• /
• 2018

터널 굴착시 지반진동을 감소시키기 위해 굴착면에 부분적인 자유면을 형성하고 제어발파를 수행하는 자유면 발파공법이 적용되어 왔다. 본 연구에서는 다이어몬드 와이어 쏘를 이용하여 인공절리를 심발부에 형성하고, 심발부 발파 시 발생되는 지반진동을 비교함으로써 인공절리에 의한 지반진동 감소를 평가하였다. 해석 결과, 일반 심발발파보다 인공절리 심발발파에서 지반진동이 감소하였으며, 수직 인공절리 심발발파보다 수평 인공절리 심발발파에서의 지반진동 감소 효과가 더 크게 평가되었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1992년도 춘계학술대회 논문집
• /
• pp.109-114
• /
• 1992

This paper describes an effect of operating condition on surface roughness in wire-cut FDM. The experimental values of surface roughness were measured by the test pieces under the condition of changing. On time, Off time, and Feed rate after fixing other conditions. The material of the test pieces is the alloy tool steel(STD 11) and was used after heat treatment. The results are as follows: 1. The surface roughness became rapidly worse according to the increase of On time and Feed rate. 2. The surface roughness became slowly better according to the increase of Off time.