• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.6
• /
• pp.714-719
• /
• 2011

The surface roughness depending on the machining method is very important because is produce a finished product through riveting, sealing, bonding, and special paint in order to curb the turbulence and air resistance which occur between the sheets. Aluminum alloy 2024 which is widely used for interior and exterior material of aircraft are tested. Jin-young JW-60C wire cutting machine was used in this experiment. In this paper, the experimental investigation has been performed to find out the influence of the surface roughness and surface shape characteristics on the wire-cut EDM of discharge energy in aluminium alloy 2024. The selected experimental parameters are peak current, no-load voltage, off time and feed rate. The experimental results give the guideline for selecting reasonable machining parameters. The high discharge energy on the idle time, almost no change in surface roughness can be seen.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38C no.7
• /
• pp.563-572
• /
• 2013

Based on this paper, in case of the on-line account system in finance industry temporarily stops working because of the on-line data change from 00:00 to 00:30, it conducts in extra placement server and the director update is carried out via center cut or on-line server to make the service possible through customer director reproduction revision. So, from the simulation result in financial operating system, We retain the batch director & backup director securely about the important time data in each account classes on-line director without even one second interruption.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.149-156
• /
• 2002

Field measurements were carried out in this study to investigate the behavior of cut and cover tunnel such as the distribution and the magnitude of the earth pressure during back fill process of the ground material. Three kinds of measuring instruments, such as the earth pressure load cell, the concrete strain gauge and the reinforcing bar meter of embedded type in concrete structure were installed and measured. Earth pressure load cells, installed after construction of the tunnel lining, measure the outside forces acting on the tunnel lining with radial directions. Three load cells were installed at the crown, the right and the left shoulder of the tunnel, respectively. Three sets of reinforcing bar meter were installed in the double reinforcements of the tunnel lining and their locations were the same with the position of the earth pressure load cells. Concrete strain gauge was installed only one site of the upper compressive part at the tunnel crown. Based on the measuring results in the field, the deformation and the earth pressure acting on the tunnel lining were investigated with the back fill process of the ground material. Considerations on the validity of the measuring results were paid. For the analysis of measurements, after dividing back fill process into three steps, various factors which affect on the behavior of tunnel lining were investigated at each step.

• Asian Journal of Turfgrass Science
• /
• v.4 no.2
• /
• pp.133-144
• /
• 1990

This experiment was carried out to study the effect of pure nitrogen fertilization on botanical composition of grassland in 1987~ 1988 under practical conditions at the " Federal Institute for Agriculture in the Alps" in Austria. The application rates were 0, 30, 60, 90 and 120kg/ha/cut, the cutting regimes 3-, 4 , 5- and 6-cuts/year. The results were as follows: 1. Only PK fertilization resulted in higher botanical composition of Trifolium repens among legumes in grassland, which was increased by cutting frequency .2. Nitrogen fertilization on three-cut areas resulted in higher existence of generally valuable tall grasses such as Arrhenotherum elatius Trisetum flavescens and Dactylis glomerata . On the other hand, nitrogen fertilization on four-, five- and six-cut areas showed mainly Doctylis glomerato and Poa pratensis appearance. 3.For some cases, appearance of less valuable grasses, herbs and weeds such as Agropyron repens, Poa trivialis, Poa annua, Setoria viridis, Aegopodium podagra rio, Men landrium rubrum, Taraxacum officlnale, Achillea millefolium, Rorippa sylvestris and Polygonum ocleulare was *Bundesanstalt fur alpenlandische Landwirtschaft Gumpenstein(A-8952 Irdning, 6sterreich) increased on medium and high rates of N fertilized areas. 4.Reduction of sward density may also diminish the advantages of nitrogen fertilization and may be threatened by mainly high dressings of nitrogen combined with too late utilization of the sward. 5.Location altered the efficiency of nitrogen fertilization on botanical composition.mposition.

• Journal of the Semiconductor & Display Technology
• /
• v.17 no.3
• /
• pp.46-52
• /
• 2018

Slitting, which is supposed to be one of the most critical processes in Li-Ion battery manufacturing, is supposed to cut off the uncoated parts of the foil, and cut the wide foils into the size of the Li-ion batteries. Vibrations of slitting machines are the most critical factors for uneven cut surface such as surface roughness and burr, which are the main reasons of the tearing of microporous membranes to separate the cathodes and the anodes, and eventually causing explosion of the batteries. In this study, the structure of a slitting machine has been analyzed through computer simulations to figure out the main reasons of the vibrations. The result of the study shows that simple design alterations of the supporting area and roller without modifying the main structure of the machine can suppress the vibrations effectively, and further to prevent the devastating explosion.

• Nuclear Engineering and Technology
• /
• v.54 no.12
• /
• pp.4560-4570
• /
• 2022

Dynamic fault tree (DFT) and its related research methods have received extensive attention in safety analysis and reliability engineering. DFT can perform reliability modelling for systems with sequential correlation, resource sharing, and cold and hot spare parts. A technical modelling method of DFT is proposed for modelling ship collision accidents and loss-of-coolant accidents (LOCAs). Qualitative and quantitative analyses of DFT were carried out using the cutting sequence (CS)/extended cutting sequence (ECS) method. The results show nine types of dynamic fault failure modes in ship collision accidents, describing the fault propagation process of a dynamic system and reflect the dynamic changes of the entire accident system. The probability of a ship collision accident is 2.378 × 10^-9 by using CS. This failure mode cannot be expressed by a combination of basic events within the same event frame after an LOCA occurs in a marine nuclear reactor because the system contains warm spare parts. Therefore, the probability of losing reactor control was calculated as 8.125 × 10^-6 using the ECS. Compared with CS, ECS is more efficient considering expression and processing capabilities, and has a significant advantage considering cost.

• Journal of Wind Energy
• /
• v.2 no.1
• /
• pp.90-96
• /
• 2011

The purpose of this paper is to describe the control system for optimal performance of 2MW gearless PMSG wind turbine system, and to afford some techniques of the algorithm selection and design optimization of the wind turbine control system through analysis of load calculation and control characteristic. Wind turbine control system is composed of the main control system and remote control and monitoring system. The main control system is industrial PC based controller, and the remote control and monitoring system is a server based computer system. The main control system has a supervisory control of the wind turbine with operation procedures and power-speed control through the torque control by pitch angle. There are some applications to optimize the wind turbine system at the starting mode with increasing of rotor speed, and cut-in operating mode to prevent trundling cut-in and cut-out, a gain scheduling of pitch PID controller, torque scheduling and limitation of generation power by temperature limitation or remote command by remote control and monitoring system. Also, the server operation program of the remote control and monitoring system and the design of graphical display are described in this paper.

• Journal of Fashion Business
• /
• v.27 no.6
• /
• pp.66-84
• /
• 2023

Handbags are a part of fashion and while their significance and value are increasing, research on this topic is lacking. This study defines handbags and categorizes the materials used for making handbags, sewing methods, expression techniques, and terminologies related to accessories. A total of 1,743 handbags that were released from the Spring 2020 to Fall 2023, Ready-to-Wear collections by 8 selected brands (Hermes, Dior, Fendi, Chanel, Louis Vuitton, Prada, Gucci, and Alexander McQueen), were analyzed. Out of these, 732 unique designs, excluding those with only color variations, were studied. The most common sewing methods were 'Cut, sewing, and edge painting', 'Cylinder arm sewing', 'Cut, edge painting, and sewing', and 'Inverted seam', in that order. Slim strap designs primarily used the 'Cut, sewing, and edge painting' method, whereas the body, especially with narrow and hard leather, was best suited for the 'Cylinder arm sewing machine'. For expression techniques, the most frequently used methods were 'Quilting', 'Metal Eyelet', 'Embossing', 'Printing', 'Punching', and 'Weaving', respectively. The characteristics of each brand's production methods, expression techniques, and accessories were as follows: First, the exposure of logos and monograms is prominent. Unlike clothing, handbags often prominently feature the brand's logo or monogram. Second, signature quilting is a prominent feature. Quilting effectively conveys the brand's signature style, providing cushioning, volume, and pattern effects. Third, sustainable development is a growing trend. Brands are increasingly applying eco-friendly and socially responsible designs.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.6
• /
• pp.559-573
• /
• 2007

Orthotropic steel decks are manufactured by welding thin plates therefore it is inevitable that there are abundant works of welding process. On connection of transverse rib web, crossing point of longitudinal rib, transverse rib and deck plate and cut-out parts of transverse rib are the significant position of stress concentration because of out of plane and oil-canning deformation caused by longitudinal rib distortion with shear force and distortion. At the current research, the crossing point where the orthotropic steel decks's effect of improving fatigue performance are high, not placing scallop and diaphragm which have same plane with transverse rib placed inside of longitudinal rib at the same time, the reduce effects of stress concentration at the cut-out section and the crossing are high. Especially the installation of the diaphragm causing great effects based on research results to stress concentration appearance reduce effects at the cut-out section, putting radius of curvature of the diaphragm's top and bottom as a target, as a result of carrying out the parametric analysis an optimal diaphragm form that has great effects in fatigue performance came to a conclusion. Also based on optimal diaphragm form, an advantage of the diaphragm optimal setting position for improvement of the fatigue performance came to a conclusion.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.15 no.3
• /
• pp.175-185
• /
• 1995

This experiment was carried out to investigate the optimum rates of animal excreta(cattle slurry-N) for the highest dry matter production and improve the nutritive values of reed canarygrass with different cutting frequency. The results are summarized as follows; The highest relative dry matter yields for annual dry matter yield were 42.2% and 45.2% at 3rd cut in 3 and 4 cuttings, and 34.7% at 4th cut in 5 cuttings, respectively. The annual dry matter yields of non slurry-N application plot showed were from 6.8 tons to 8.0 tons/ha in all cutting frequencies. The highest annual dry matter yield obtained was in 3 cuttings. The annual dry matter yield increased with an increase of applied rates of slurry-N in all cutting frequencies. Annual dry matter yield was produced by 3.3 tons/ha at rates of 90 kg N/ha/cut in 3 cuttings, and more 1.7 tonsha and 2.4 tons/ha at rates of 30 kg N/ha/cut in 4 and 5 cuttings than that of non slurry-N application plots. The contents of crude protein were 12.01% and 15.0% at rates of 90 kg N/ha/cut in 3 and 4 cuttings, and 16.59% at rates of 120 kg N/ha/cut in 5 cuttings, respectively. On the contrary, the content of acid detergent fibre(ADF) showed the lowest values at same rates of slurry-N application in each cutting. J. The average content of crude protein was significantly increased with cutting frequencies, and they were 11.43%, 13.53% and 15.53% in 3, 4 and 5 cuttings, respectively. The average contents of acid detergent fibre(ADF) were 40.27%, 40.53% and 37.06% in 3, 4 and 5 cuttings. The values of 5 cuttings were significantly lower than other cutting frequencies, but the values of acid detergent fibre(ADF) was not significantly different between 3 and 4 cuttings. 6. The efficiency of dry matter production to slurry-N application rates showed the highest values of 18.9 kg and 15.7 kg DM/kg N at rates of 30 kg N/ha/cut in 3 and 5 cuttings, and 16.3 kg DM/kg/ N at rates of 90 kg N/ ha/cut in 4 cuttings. The efficiency of total nitrogen yield to slurry-N application rates were the highest values of 0.51 kg and 0.43 kg W k g N at rates of 30 kg N/ha/cut in 4 and 5 cuttings, and 0.52 kg TN/kg N at rates of 90 kg N/ha/cut in 3 cuttings, respectively. 7. The ranges of economic slurry-N rates were estimated as the 107.2-151.0 kglha, 359.1-375.7 kgha and 160.3-236.9 kg/ha in 3, 4 and 5 cuttings, and marginal dry matter yields were 9.6-10.0 tons/ha, 12.4-12.6 tons/ha and 9.0-9.7 tons/ha in 3, 4 and 5 cuttings, respectively. 8. The limiting sluny-N application rates to maintain the highest dry matter yields were estimated to be 420.0 kg/ ha, 440.6 kg/ha and 666.3 kg/ha in 3, 4 and 5 cuttings.