• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.109-114
• /
• 1992

This paper describes an effect of operating condition on surface roughness in wire-cut FDM. The experimental values of surface roughness were measured by the test pieces under the condition of changing. On time, Off time, and Feed rate after fixing other conditions. The material of the test pieces is the alloy tool steel(STD 11) and was used after heat treatment. The results are as follows: 1. The surface roughness became rapidly worse according to the increase of On time and Feed rate. 2. The surface roughness became slowly better according to the increase of Off time.

• Advances in materials Research
• /
• v.5 no.2
• /
• pp.67-80
• /
• 2016

The objective of the present work is to optimize process parameters namely, cutting speed, feed rate, and depth of cut in milling of AISI 304 stainless steel. In this work, experiments were carried out as per the Taguchi experimental design and an $L_{27}$ orthogonal array was used to study the influence of various combinations of process parameters on surface roughness (Ra) and material removal rate (MRR). As a dynamic approach, the multiple response optimization was carried out using grey relational analysis (GRA) and desirability function analysis (DFA) for simultaneous evaluation. These two methods are considered in optimization, as both are multiple criteria evaluation and not much complicated. The optimum process parameters found to be cutting speed at 63 m/min, feed rate at 600 mm/min, and depth of cut at 0.8 mm. Analysis of variance (ANOVA) was employed to classify the significant parameters affecting the responses. The results indicate that depth of cut is the most significant parameter affecting multiple response characteristics of GFRP composites followed by feed rate and cutting speed. The experimental results for the optimal setting show that there is considerable improvement in the process.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.9B
• /
• pp.1690-1696
• /
• 1999

Video sequence should be hierachically classified for the content-based retrieval. Cut detection algorithm is an essential process to classify shots. It is generally difficult for cut detection algorithms to detect cut points since a current frame is compared with a previous one, because movement of camera or object made adrupt scene change. We reduce ratio of failed cut detection so that compare the difference between frames of predicted cut point and their neighbors. In this paper, first we get predicted cut point, then we judge that the predicted cut point is true point or not. And we extracted DC images in MPEG video sequence for comparison. As a result of experiments. We confirmed that the cut detection ratio of the proposed algorithm is higher than of any other algorithms.

• Korean Journal of Food Science and Technology
• /
• v.29 no.6
• /
• pp.1316-1318
• /
• 1997

The isolated ${\kappa}-Casein$ on gel permeation chromatography was hydrolyzed by chymosin, trypsin, and pepsin. The 3% TCA soluble portion of the hydrolysates were dialyzed on the angiotensin-I converting enzyme (ACE) inhibition rate (%,) and inhibitory activity $(IC_{50})$ were determined. The trypsin hydrolysate exhibited the highest ACE inhibition rate while the chymosin hydrolysation showed the lowest activity. The hydrolysate was dialyzed using dialysis membrane with various molecular cut-offs, and $IC_{50}$ was determined. As the pore size of the dialysis tubing increased, the ACE inhibitory activity decreased.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.66 no.4
• /
• pp.375-382
• /
• 2021

For stable cultivation in double cropping, it is important to use potato (Solanum tuberosum L.) cultivars with a short dormancy period of 50-70 days and plant seed tubers of appropriate type and size. An experiment was conducted during 2018-2019 to investigate the effects of seed tuber type and size on growth and yield performance in double cropping. Whole tubers of three sizes (10-20 g, 30-40 g, and 50-60 g) and conventional cut tubers weighing 30-40 g from three cultivars with different dormancy periods, namely 'Daeji' (40-60 days), 'Eunsun' (50-60 days), and 'Saebong' (50-80 days), were planted, and their field performance was compared. Regardless of the cultivar, the increase in the whole tuber weight up to 30-40 g led to fast emergence, thereby increasing ground cover rate, shoot growth rate, and tuber growth rate, which ultimately improved tuber yield by 33-54%. Comparing the whole and cut tubers, 'Daeji' and 'Eunsun' showed similar growth and yield performance; as such, the performance of whole tubers weighing 10-20 g was comparable to that of cut tubers weighing 30-40 g. However, 'Saebong', a cultivar with relatively long dormancy period, performed better with cut tuber than with whole tubers. Based on these results, we recommend the use of whole tubers weighing over 30 g for double cropping. Further studies to break tuber dormancy are warranted in cultivars with relatively long dormancy periods (50-80 days), such as 'Saebong'.

• Journal of the Korean Electrochemical Society
• /
• v.7 no.1
• /
• pp.32-37
• /
• 2004

The charge/discharge capacity of natural graphite anode in lithium secondary batteries was examined as a function of charge/discharge rate. When the natural graphite anode was galvanostatically cycled in the range of 0.0-2.0V $(vs.\;Li/Li^+)$, the charging capacity decreased with an increase in the charging rate, which is caused by an earlier approach to the charging cut-off (0.0 V) before the complete charging that is in turn caused by an ever-increasing overpotential at higher rates. Even if the overpotential of discharging reaction also increased at higher discharge rates, the discharging reaction took place in the range of 0.0-0.3 V that is far below the discharge cut-off (2.0 V). As a result, the discharge capacity was not affected by the discharge rate because all the lithium ions once intercalated are fully discharged even at high current condition. As the overpotential of lithium deposition reaction also increased at high current condition, the charge capacity of natural graphite could be enlarged by lowering the charging cut-off voltage below 0.0 V, There is, however, a limitation for the lowering of cut-off voltage because the resistance for lithium deposition is smaller than that of lithium intercalation into graphite. When the charge cut-off voltage was lowered down to -0.04 V under IC condition, lithium ions were inserted into graphite without lithium deposition such that the discharge capacity could be raised up to $11\%$.

• Journal of Convergence for Information Technology
• /
• v.10 no.1
• /
• pp.75-81
• /
• 2020

This study analyzed the annual difference of firm's book income, taxable income and BTD that before and after the 2009 corporate tax rate cut and 2018 corporate tax rate increase. ANOVA analysis was performed for each item by year, and post hoc was performed after homogeneity test of variance. The research results are as follows. First, the book income at corporate tax rate cut was higher than taxable income, and BTD in 2008 was significantly different from other years. Second, the book income at corporate tax rate increase was less than taxable income, and BTD in 2017 was also significantly different from other years. In other words, the firm is performing appropriate profit adjustments to reduce of tax burden when the corporate tax rate changes. Because of this, the BTD in the year immediately before the corporate tax rate change is different from other years.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.5
• /
• pp.87-95
• /
• 2000

The numerical analysis and the experiments are carried out to develop the design program for the flow control valve attached to the vane pump for power steering. The factors affecting the flow rate characteristics are analyzed by the experiments and the numerical analysis. The results are summarized as follows; (1) the main factors affecting to the first and second control flow rate are the diameter of big and small rod of the spool. (2) the cut off is mainly affected by the main spring constant, the initial displacement of main spring and the small diameter of the spool. (3) the dropping slope characteristics are decided by the chamfer of spool and the dynamic characteristics of the spool.

• Journal of the Korean Society of Safety
• /
• v.9 no.4
• /
• pp.17-28
• /
• 1994

Chip breaking is important in lathe work for maintaining good surface of the products and safety of operator. The purpose of this study is to investigate the performance of chip breaking and chip shape resulted from the carbide inserts with grooved type and obstruction type chip breaker. Experiments have been performed under the following cutting conditions, (1) constant cutting speed with variable depth of cut and feed rate, (2) constant depth of cut with variable cutting speed and feed rate. Also, the flying distance of chip and it's distribution have been investigated. As a results, good performance of chip breaking can be obtained for small radius of curvature and land width of grooved type chip breaker. And the thickness of chip increase with the increase of feed rate and decrease of cutting speed, and the chip breaking becomes easier with the increase of chip thickness due to the large deformation rate. Obstraction type chip breaker shows better performance of surface roughness than the grooved type. The flying distance of the chips over 90% are less than 1 meter, and the distance decreases as the feed rate decreases.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.1
• /
• pp.39-45
• /
• 2012

Currently, the aircraft industry, aircraft parts as well as airframe have been developed in producing, the aircraft parts and fuselages have been produced the product by cutting rather than forging and casting because of the residual stress and stress concentration. In this study, the aircraft is being used in many parts of aluminium alloy 2024 in wire-cut E.D.M. The selected experimental parameters are peak current, no-load voltage, off time and feed rate. It is found that cutting mountain part on surface roughness of the curve 0.3mm than 0.25mm diameter wire electrode is stable in many uniform distribution.